• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.289-292
• /
• 2006

The purpose of this study was to evaluate a performance of latex-modified repair material applied to the substrate concrete. The experimental variables were latex-cement ratios (5, 10, 15%), polymer(0.5%, 1%) and admixtures. The flow, air content, compressive strength, flexural strength were tested. Test results showed that compressive and flexural strength decreased by adding hydroxyethyl cellulose and increasing water-binder ratio. The compressive and flexural strength were increased when addition of defoamer.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 춘계학술발표논문집
• /
• pp.7-16
• /
• 1999

The aim of this research was to evaluate the influences of coating components and structures on ink absorbency. The ink absorbency was measured as porosity, K&N ink absorption, gloss and ink set-off. In order to obtain the relationship between the coating structure and the ink absorbency, the binder level was adjusted and two types of pigments were examined. One of the pigments was known to make the porous coating structure and the other one had strong ink affinity. The effects of coating components were studied by applying six different types of latex and various additives . In this research, CLC(cylindrical laboratory coater) and Prufbau printability tester were used. It was found that the decreasing latex dosage and introducing porous pigment were effective solutions to increase ink absorbency. However, the ink absorbency could not be improved by applying the fine pigment even though it had strong ink affinity. Among the characters of the latex, particle size and surface tension were found to have the strong effect on ink absorbency. The ink absorbency increased with large particle size and low surface tension latex. The additives were varied and it was found that applying to the top coating was effective.

• 콘크리트학회논문집
• /
• 제14권3호
• /
• pp.402-408
• /
• 2002

본 연구에서는 SBR 라텍스 및 재유화형 EVA 분말수지를 혼입한 투수성 폴리머 시멘트 콘크리트를 제조하여 투수성 폴리머 시멘트 콘크리트의 공극률, 투수계수, 강도 및 동결융해 저항성에 미치는 폴리머-시멘트비의 영향을 구명하였다. 그 결과, 투수성 폴리머 시멘트 콘크리트의 공극률, 연속공극률 및 투수계수는 폴리머-시멘트비의 증가에 따라 감소하는 경향을 보였으며, 압축, 인장 및 휨강도는 폴리머-시멘트비의 증가에 따라 증가하였다. 또한 투수성 폴리머 시멘트 콘크리트의 동결융해 저항성 역시 폴리머의 혼입에 따라 증진되었다. 이와 같은 효과는 폴리머의 혼입에 의해 시멘트 수화물과 골재간의 접착성이 개선되기 때문이라 판단된다.

• 한국인쇄학회지
• /
• 제18권1호
• /
• pp.83-94
• /
• 2000

The mottling in coated paper is one of the most difficult problems to solve in the area of offset printing. The prevention of mottling requires optimization of coating color formation, especially the minimum of binder migration. In this paper, we studied a mottling. Kaolin clay and CaCO3 as pigment, starch and latex as binder of coating color were used in this study. We have measured surface property of 24 coated samples through k value, mottle value and transferred ink. In the equation of Walker and Fesko, the value of k was the highest and that of mottle and the mount of transferred ink were the lowest in kaolin 60 part. And it is more easy to analyze the various surface of coated paper when sample was exposed on IR.

• 콘크리트학회논문집
• /
• 제14권4호
• /
• pp.608-614
• /
• 2002

본 연구는 고로슬래그 미분말 및 SBR 라텍스를 혼입한 폴리머 시멘트 모르타르의 강도성상에 미치는 고로슬래그 치환율 및 폴리머-결합재비의 영향에 대해 검토하였다. 그 결과, 고로슬래그 미분말을 혼입한 오토클래이브 양생 폴리머 시멘트 콘크리트의 압축 및 인장강도는 고로슬래그 치환율이 증가함에 따라 증가하였고, 고로슬래그 치환율 40%에서 최대치에 달하였다. 고로 슬래그 미분말을 혼입한 오토클래이브 양생 폴리머 시멘트 콘크리트의 압축 및 인장강도는 폴리머-결합재 비의 증가에 따라 증가하는 경향을 보였다. 특히, 고로슬래그 치환율 40%의 오토클래이브 양생 SBR 혼입 폴리머 시멘트 콘크리트는 고로슬래그 미분말 및 SBR 미혼입 폴리머 시멘트 콘크리트보다 약 3배 이상의 높은 인장강도를 나타냈다. 이같이 높은 강도 개선은 SBR 라텍스의 혼입에 의해 시멘트 수화물과 골재간의 접착력이 개선되기 때문이라 판단된다.

• 펄프종이기술
• /
• 제34권5호
• /
• pp.1-17
• /
• 2002

The immobilization and consolidation of the model coatings based on the plastic pigment and latex binder of known particle sizes were theoretically Studied in terms of the dense random packing of binary spheres and varying extent of latex film shrinkage. The porosity of the model coatings was calculated based on three proposed latex shrinkage models: Maximum, Minimum, and Linearly Decreasing Latex Shrinkage. The increasing extent of latex shrinkage was calculated up to the critical pigment volume concentration(CPVC) as a function of plastic pigment volume fractions, and the maximum latex shrinkage was estimated from the CPVC. Also, the number of pores and the average equivalent spherical pore diameters were calculated based on those proposed models. The opacity and gloss of the model coatings on polyester films were measured and their porosity was also determined by a simple coat weight-thickness method. As expected, various coating structure-property-composition relationships, such as opacity, gloss, porosity, etc., were shown to exhibit sharp transitions near the CPVC. The CPVC values determined by the opacity, gloss, and porosity vs. PVC relationships, respectively, agreed very well with each other. Especially, the CPVC's determined by the opacity and porosity vs. PVC curves were identical. The comparison between the theoretically calculated and experimental porosity values showed that the intermediate value between the maximum and minimum latex shrinkage would best fit the experimental porosity data. The effect of plastic pigment particle size on the optical properties and porosity of model coatings was also studied and it was observed that the coating opacity and porosity increased with increasing plastic pigment particle size, but the gloss decreased. The ink gloss of the uncalendered model coatings applied onto commercial sheet offset coated papers was shown to be affected by both the coating gloss and porosity: the higher the coating gloss, the higher the ink gloss, but the higher the coating porosity, the lower the ink gloss. Their printability was also studied in terms of the number of passes-to-fail and the rate of ink setting as a function of both plastic pigment volume fractions and plastic pigment particle sizes. A minimum crack-free temperature(MCR) of latex-bound coatings was proposed to better predict the behaviors of latexes as coating binders. The wet state of model coating dispersions, the surfaces of consolidated model coatings, and their internal structure were examined by both electron and atomic force microscopy, and their micrographs were found to be consistent with our immobilization and consolidation models.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2008년도 제38차 학술발표대회
• /
• pp.22-24
• /
• 2008

신발 및 피혁 제품의 분쇄는 섬유의 길이와 물리적인 특성을 고려하여 3${\sim}$4mm 정도의 섬유 길이로 절단되는 Niagara beater가 우수하였고, 섬유간 접착력을 부여하는 Binder 물질로는 NR latex와 EVA emulsion이 인장, 인열강도가 우수하여 NR latex와 EVA emulsion이 7:3의 비율로 혼합하여 사용하는 것이 가장 좋은 결과를 나타내었다. 또한 코팅 처리된 신발 재단 폐기물의 경우 Niagara beater에 Alcalase를 투입하는 것이 분쇄시간의 단축에 유리한 경향을 나타내었고, 건조 공정은 90$^{\circ}C$이하로 유지하는 것이 $^{\triangle}$E값의 변화가 거의 없었고 100$^{\circ}C$에서는 $^{\triangle}$E값이 7.55를 나타내어 황변이 발생하였다.

• 한국세라믹학회지
• /
• 제40권10호
• /
• pp.931-935
• /
• 2003

A complex-shaped part was successfully fabricated by Laminate Object Manufacturing (LOM) technique using silicon nitride tape with aligned silicon nitride whisker seeds. The ceramic tape was cut using a commercial cutting plotter according to the cross section drafts generated by slicing a 3-D model, and then the tapes were stacked sequentially. In order to improve adhesion between the tapes, stacking was performed under vacuum. After binder burnout, the part was encapsulated using latex emulsion and was cold isostaically pressed under 250 ㎫. It was sintered to 98.5% TD at 2148 K for 4 h under 2 ㎫ nitrogen pressure.

• 한국산림과학회지
• /
• 제46권1호
• /
• pp.1-9
• /
• 1980

본(本) 연구(硏究)는 산지이식(山地移植)에서 Jiffy pot를 fiber pot로 대체가능(對替可能)한가 알아보기 위해 수행(遂行)되었다. fiber pot는 fiber, wood waste particle, particle 량(量)의 10%에 해당하는 bark powder로 만들어졌고 또 latex가 결합제(結合劑)로 첨가(添加)되었다. pot는 식물(植物)이 자라는 동안 pot벽(壁)의 wood fiber 분해(分解)에서 생기는 배양토(培養土)의 N흠핍증(欠乏症)을 막기 위해 충분(充分)한 요소액(尿素液)으로 spray되었다. fiber pot의 이용가능성(利用可能性)은 온실조건(溫室條件)하에 두 수종(樹種)의 service test에서 Jiffy pot와 비교(比較)되었다. 결과(結果)는 다음과 같이 요약(要約)된다. 1. 비중(比重), 비인열도(比引裂度), 비파열도(比破裂度)에 있어서 30% wood fiber+10%의 bark powder를 포함(包含)한 70% particle과 3% latex로 된 fiber pot가 Jiffy pot에서와 같은 좋은 결과(結果)를 나타냈다. 흡수력(吸水力)에 있어서는 50% fiber+50% particle과 3%-latex로 된 fiber pot가 가장 좋은 결과(結果)를 나타냈다. 뿌리의 pot벽(壁) 관통(貫通), 취급편의성(取扱便宜性)에 대(對)한 상기(上記) 물리적(物理的), 기계적(機械的) 성질(性質)을 고려(考慮)할 때 30%fiber+70%particle과 3%-latex로 된 fiber pot가 좋을 것으로 보였다. 2. Jiffy pot와 마찬가지로 fiber pot에서도 묘목생장(苗木生長)에는 아무런 해(害)가 없었다. 뿌리의 pot벽(壁) 관통능력(貫通能力)은 Jiffy pot보다 fiber pot가 다소 뒤지나 운반(運搬)에 의(依)한 pot의 손상(損傷)은 Jiffy pot보다 약간 더 경미(輕微)했다.

• 펄프종이기술
• /
• 제41권2호
• /
• pp.26-33
• /
• 2009

A new testing method to evaluate the deposition potential of white pitch was developed. The new method involves depositing the potential white pitch particles on the air bubble covered plastic film in the pitch deposit tester (PDT) developed by KRICT and analysing the deposited area of white pitch using an image analyzer. In addition, the effect of two important factors (pH and calcium hardness) on white pitch deposition potential was elucidated. When pH of the coated broke stock was increased from neutral to alkali or the calcium hardness of the stock was decreased, the pitch deposit area was decreased, implying that these two factors have to be controlled during the evaluation of pitch deposition potential. It was found that hydrophobicity of the surface of latex binding films repulped is a key factor influencing white pitch deposition.