• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.291-296
• /
• 2008

In order to improve the leakage prediction and rotordynamic analysis of an annular seal with a smooth rotor and circumferentially grooved stator, CFD analysis using FLUENT has been performed to determine the groove penetration angle a which is the angle of separation line between control volumes II and III in groove section of Ha and Lee's three-control-volume theory. Validation to the present analysis using new penetration angle determined by the CFD analysis is achieved by comparisons with the results of published Ha and Lee's analysis. For the leakage prediction the present analysis shows slight improvement and CFD results yields the best. Direct damping and cross-coupled stiffness coefficients are predicted better to the experimental ones. However, direct stiffness coefficient is predicted worse.

• 대한기계학회논문집
• /
• 제18권2호
• /
• pp.380-388
• /
• 1994

Study on the chaotic stirring has been performed numerically and experimentally for a shallow rectangular tank accompanying a vortex shedding. The model is composed of a rectangular tank with a vertical plate with a length half the width of the tank. The tank is subject to a horizontal sinusoidal oscillation. The chaotic stirring was analysed by Poincare sections, unstable manifolds and Lyapunov exponents. As Reynolds number is increased the stirring effect is decreased due to the growth of a regular regions near the lower surface of the tank. In the other hand decrease of Reynolds number gives a weaker vortex shedding resulting in the poorer stirring effect. It was also found that the Lyapunov exponent is the highest at the dimensionless period of 1.3-1.5, which seems to be the best condition for the efficient stirring. The experimental visualization for the deformation of materials exhibits the striation pattern similar to the unstable manifold obtained numerically.

• 소성∙가공
• /
• 제20권6호
• /
• pp.427-431
• /
• 2011

In general, hot stamped component is trimmed by costly and time consuming laser cutting when the material strength is over 1,500MPa. The aim of this work was to demonstrate that the trimming die life is improved and the trimming load is decreased by lowering the strength of the region to be trimmed. The model employed in this study was a hat shape, similar to the cross section of many hot stamped products. FE-analysis of hot stamping process was performed to evaluate the effect of tool shape on cooling rate at the area to be trimmed. The best tool shape was thus identified, which created slower cooling and lower hardness at the region to be trimmed. The wear at the cutting tool edge was also reduced.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.813-816
• /
• 2006

Complex pressure pulsation phenomenon in fuel rails is generated by rapid opening and closing of injectors and it commonly causes undesirable noise. In this study, fluid-structure interaction analyses based on CFD and FEM have been conducted to examine the pulsation damping characteristics for different shapes of fuel rails. It is shown from the present results that the fuel rail with a high aspect ratio rectangular cross section seems to be best in order to reduce the pressure pulsations. It also agrees well with the previous experimental test by Mizuno, K. et al.

• 한국염색가공학회지
• /
• 제28권3호
• /
• pp.183-188
• /
• 2016

The uniformly dispersed p-Aramid chopped fiber in a variety of rubber was investigated. The cross section and surface properties in a variety of rubber were characterized by scanning electron microscopy(SEM), weight, tensile strength, cold resistance measurements. The 1mm p-Aramid chopped fiber better uniformly dispersed than the other p-Aramid chopped fiber. The p-Aramid of lmm chopped fiber showed excellent adhesion in rubber composite because of homogeneous dispersion. Consequently, the best 1mm chopped fiber and rubber improved the strength of the composite.

• EDISON SW 활용 경진대회 논문집
• /
• 제4회(2015년)
• /
• pp.184-190
• /
• 2015

On wide variety of fields, studies on active twist control are becoming more active. For effective twist control, blades have to have low torsional stresses with high torsional deformations to the same magnitude of torque acting on its cross-section. In this study, 2D sectional analysis and 3D finite element analysis were made for 5 different blades with each having different cross - sections which have different spars. The results from 2D sectional analysis, were then put into 3D blade deformation and stress calculations which lead to analysis. Outcomes from 2D and 3D analysis, showed that on the same torque and concentrated load conditions, the blade with 'C' shaped spar was the best of all the blades which were used in this study.

• Nuclear Engineering and Technology
• /
• 제43권1호
• /
• pp.75-82
• /
• 2011

The neutron multiplication factor in spent fuel storage racks, in which a stainless steel plate encloses a fuel assembly, was evaluated according to the variation of distance between the fuel assembly and stainless steel plate, as well as the pitch. The stainless steel plate position with the lowest multiplication factor on each pitch consistently appeared as 6mm or 9mm away from the outmost surface of the fuel assembly. Because the stainless steel plate has a thermal neutron absorption cross section, its ability to absorb neutrons can work best only if it is installed at the position where thermal neutrons can be gathered most easily. Therefore, the stainless steel plate position should not be too close or too far away from the fuel assembly, but it should be kept a pertinent distance from the fuel assembly.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1999년도 춘계학술대회 논문집
• /
• pp.200-207
• /
• 1999

The purpose of this research is to setup the design procedure of low noise rolling stocks. Noise sources are identified at a field test, and the contribution of noise sources to each part of car interior is ensured by sound intensity measurement technique. Added material to each section of the carbody makes it possible to identify absorption or reflection performance of each part to the anterior random noise. Such experimental tests to the exterior noise intruding through the floor represent that the best countermeasure on the floor is to implement reflecting material which can properly interfere noise. Design procedure of low noise rolling stocks is set through several experiments.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1999년도 Proceedings of the 1999 Annual Conference The Korean Society of Agricutural Engineers
• /
• pp.465-472
• /
• 1999

Hydraulic model tests are performed to find economical and hdrqulically stable design of cooling water intake channel of steam power plant. The result of tests show that the standard distributiion of y-components in the chamber of CWP(circulating Water Pump) are recommended below 3.5 to maintain hydraulic stability, so that this value is considered as the design criteria. Common basin is necessary to improve the hydraulic stability of inflow, however the longer basin does not always improve the hydraulic stability , and the optimal length of basin can be found in some range. From the results the flow stability maintained the best condition when the length of basin is 7.2m. Beside the standard tests the auxiliary tests like edge , baffle, trapezoidal section and increase of pump capacity are carried out based on the optimal condition foudn in the standard tests. From the series of tests the economical and hydraulically stable design of intake channel was proposed.

• 한국결정성장학회지
• /
• 제23권2호
• /
• pp.67-75
• /
• 2013

In order to improve osseo-integration of a dental implant with bone crystal we studied an implant with holes inside its body to deliver bioactive materials based on a proposed patent. After bioactive material is absorbed, bone crystal can grow into holes to increase implant bonding in addition to surface integration. The larger cross section area of outlet holes showed the less values of the maximum stress, and the stress concentrations near the uppermost outlet holes were also reduced with an increasing number of outlet holes. The conclusion, that the uppermost outlet design improvement was most effective to reduce the stress concentration and improve the growth rate of bone crystal, could be drawn. After the design optimizations, Type 6-C had provided the best results in this study. The overall shape optimization studies on the shape, location, number, and so on, of the outlet holes, should be carried out further.