• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.489-494
• /
• 1998

This paper describes the possibility to reuse concrete waste produced by demolition of reinforced concrete structures as aggregate for concrete from the viewpoint of strength. Concrete rubble obtained from the demolished buildings at Taejon were crushing machine to reuse as coarse aggregate. The strength properties, such as compressive strength, splitting tensile strength, bending strength and shear strength, of recycled and normal concrete were examined and compared experimentally when water cement ratio was varied. From the results of this study, it was thought that in case of non-washed aggregate concrete, strength properties of recycled coarse aggregate is similar to that of normal concrete, In W/C 55%~45%, stress-strain curve of recycled concrete shows more stable than that of normal concrete, while in W/C 35%, it shows brittle behavior.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.147-153
• /
• 2006

Photocatalyst reaction has limit of its usage because application range mostly centered on atmosphere purification area. Thus, it is true that an alternative plans are necessary to increase usage of $TiO_2$ as photocatalyst material. (1) The result of flow felt according to $TiO_2$ replacement rate has shown that both of anatase type and rutile type over 12% deviated from desired flow, $110{\pm}5mm$. Consequently, the range below 9% will be suitable when the anatase type $TiO_2$ if used for functional additives if workability is considered. (2) After compressive strength test, replacement rate 6-9% is estimated as suitable range if $TiO_2$ is used as compressive strength material. Rutile type and anatase type are suitable for in early-age strength and long-age strength respectively. (3) It was revealed that bending strength was dramatically decreased when replacement rate was increased. The main reason were the increase of $TiO_2$ doesn't influence hydration reaction and the decrease of bending strength. (4) The result from the water purification properties test using ion-chromatograhpy has shown that the condition with anatase type $TiO_2$ was normally better than rutile type on the same replacement rate.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.5
• /
• pp.539-547
• /
• 2012

To manufacture laminated wood with improved mechanical properties by providing uniform adhesiveness, the adhesive was applied and the plate adhesive was laminated on the wood surface. Then, after laminating the wood on the top part of the adhesivebond, it was heated and dried while the adhesive was stiffened using microwaves, and the test piece was manufactured by compressing it with the press machine for thirty minutes. The temperature and the water content were examined according to the heating time of the wood heated with the microwave, and testing was conducted on the shear strength and flexural strength of the wood. In addition, the microstructure of the adhesive bond between the wood was recorded to confirm the penetrabilityinto the wood structure for the adhesive. After the test was conducted, it was found that the test piece manufactured with wood that has its water content leveled with the microwave heating showed improved shear strength and bending strength compared to the standard test piece. With regard to adhesives, liquefied polyvinyl acetate resin and plate's PVB resin were found to have superior adhesive strength. Also, after filming the cellular microstructure, it was found that when the laminated wood is heated with microwaves, the infiltration of the adhesive into the inside of the wood becomes easy, which makes it effective for improving adhesiveness.

• 한국기계연구소 소보
• /
• s.15
• /
• pp.75-87
• /
• 1985

A review was performed on fatigue life prediction and strength evaluation of shot peened parts. Fatigue strength of machine parts can be improved by shot peening due to compressive residual stresses on such parts. Compressive residual stress cannot be uniquely define by peening intensity. Several measuring methods of residual stress and the principle of hole drilling method are presented. Exploratory measurement of residual stress was performed on the shot peened SM35C plate with the hole drilling method. Fatigue life and failure location of shot peened parts under bending load can be predicted by a damage parameter which is incorporated with material properties, residual stress, and applied stress conditions. Some method are presented to predict the fatigue strength of shot peened parts at any given life. Shot peening gives its full benefit to the notched machine parts of high strength steels.

• The Journal of Advanced Prosthodontics
• /
• v.5 no.2
• /
• pp.133-139
• /
• 2013

PURPOSE. This study was to evaluate the effect of the solution temperature on the mechanical properties of dualcure resin cements. MATERIALS AND METHODS. For the study, five dual-cure resin cements were chosen and light cured. To evaluate the effect of temperature on the specimens, the light-cured specimens were immersed in deionized water at three different temperatures (4, 37 and $60^{\circ}C$) for 7 days. The control specimens were aged in a $37^{\circ}C$ dry and dark chamber for 24 hours. The mechanical properties of the light-cured specimens were evaluated using the Vickers hardness test, three-point bending test, and compression test, respectively. Both flexural and compressive properties were evaluated using a universal testing machine. The data were analyzed using a two way ANOVA with Tukey test to perform multiple comparisons (${\alpha}$=0.05). RESULTS. After immersion, the specimens showed significantly different microhardness, flexural, and compressive properties compared to the control case regardless of solution temperatures. Depending on the resin brand, the microhardness difference between the top and bottom surfaces ranged approximately 3.3-12.2%. Among the specimens, BisCem and Calibra showed the highest and lowest decrease of flexural strength, respectively. Also, Calibra and Multilink Automix showed the highest and lowest decrease of compressive strength, respectively compared to the control case. CONCLUSION. The examined dual-cure resin cements had compatible flexural and compressive properties with most methacrylate-based composite resins and the underlying dentin regardless of solution temperature. However, the effect of the solution temperature on the mechanical properties was not consistent and depended more on the resin brand.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.95-101
• /
• 2002

Physical and mechanical properties of major Korean ash species were examined. For Fraxinus rhynchophylla and Fraxinus sieboldiana, green moisture content of sapwood was almost the same value as heartwood. Heartwood of Fraxinus mandshurica, however, had slightly higher moisture content than sapwood. Green and oven dry densities of F. mandshurica were lower than those of F. rhynchophylla and F. sieboldiana. Swelling and shrinkage of sapwood in F. sieboldiana showed somewhat higher value than those of F. rhynchophylla. Longitudinal compressive strength and modulus of elasticity in F. sieboldiana were lower values than those in the other species. Shearing strength in radial section was higher than that in tangential section of all samples. It could be noted that shearing strength of F. sieboldiana demonstrated higher value than that of the other species. Three species had excellent bending properties in MOR and MOE. Impact bending absorbed energy for F. rhynchophylla and F. mandshurica did not show any significant differences.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.69-75
• /
• 2001

This study was carried out to investigate the properties of woodceramics made from thinned logs of Cryptomeria japonica. In order to find the effect of steam injection time on the woodceramics fabricated with boards, boards were made with the non-steamed treatment and steamed treatment 1, 5, 10 min. at $250^{\circ}C$. The percentage of weight loss was proportional to the increased density of board The reducing rate of length and thickness, however, decreased with increasing density of board. The rate of weight loss, length and thickness reduction in non-steamed board were slightly higher than those of steamed board. When the resin impregnation rate increased, the bending strength and compressive strength of woodceramics had a tendency to increase. The bending strength and compressive strength of woodceramics in non-steamed board was higher than those of steamed board. But there was little difference between dimensional and strength properties of woodceramics and steam injection time of board.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.3
• /
• pp.93-99
• /
• 2001

Recently the steel parts used at automobils are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, two kinds of spring steel (SAE 9254, DIN50CrV4) are used. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) on low stress condition, th 1st stage shot peening is not affected by nonmetallic inclusion under metal.(2) it is possible that the 2nd stage shot peening increases the fatigue life and the high stress but that is affected by nonmetallic inclusion under metal. (3) so far beeasily DIN50CrV4 have made high stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.1-7
• /
• 2002

This study deals with physical properties of Larch(Larix kaemferi Carr.) treated by steaming at temperatures above 100℃. Treatment conditions of this experiment were operated at regular intervals of 10℃ at temperature up to 130℃ for 10, 30 and 60 minutes by using the auto-clave. The Bending strength and compressive strength along the grain were slightly decreased with increasing the treating temperatures. There was no significant relations between wood strength and steaming temperatures. At the range from 120℃ to 130℃ of steaming temperature, it was considered that the change of composition and structure in cell wall was changed due to release of stresses. Water absorption characteristics were not affected by steaming temperature. In this experiment limits, it was concluded that physical properties of wood by steaming treatment were affected more largely by wood density than by treating temperature.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.366-372
• /
• 2002

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface deject as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know tile influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7,SAE 9254, DIN 50CrV4, ) are made. This study shows the outstanding improvement of fatigue properties at tire case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.