• Journal of Environmental Science International
• /
• v.11 no.9
• /
• pp.881-895
• /
• 2002

Sediments and river waters form the channel of Hwasun-cheon were studied in sedimentological size and geochemical analyses of metallic elements for the purposes of identification of depositional environments and geochemical characteristics. The sizes of sediments are assigned to pebble to coarse sand in mean size and polymodal in distribution. And the sediments are poorly to very poorly sorted and positively skewed. According to the grain size distributions of the sediments, the Hwasun-cheon belongs to gravel-bed river on the basis of the grain size distribution of the sediments. The behaviors of metallic elements in the sediments mainly depend on not grain size distribution but the geology connected with geomorphological reliefs near the stream. Contamination indices(CI) of Zn, Cu and Pb are 2.83 to 6.96 with average 4.31 in the sediments. Hwasun-cheon is assigned to general stream type in accordance with water quality of physical factors and chemical characteristics by Piper's diagram. Though meaningful values of BOD, T-N, T-P were locally depicted near Masan-ri, Hwasun-eup and Jiseok-cheon areas, artificial metal concentration do not represent in the most area of the stream. Sediments and river water are considered that the relatively more or less high metallic contents in the stream are originated from coal mine and urban area.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1551-1558
• /
• 1994

An experiment was conducted to investigate whether an equation of heat transfer coefficient derived form energy equation of two-phase plug flow can be actually applied to the industrial field. The heat is constantly transfered to the sand beds from the wall of heat exchanger while the sand moves down through cylindrical heat exchanger by gravity from feed hooper. To increase heat transfer, turbulators such as glass ball and steel pipe packings were used. In addition, the experiment in the case of fluidizing the sand beds was also carried out. The temperatures of the sand beds and the wall were measured along the heat exchanger axis. The density and porosity of the sand beds were also measured. The deviations of the mean velocity of sands from the velocity on the wall surface because of the slip conditions on the wall were negligible (within 3%). The heat transfer coefficients when the turbulators were used and when the sand beds were fluidized were found to be much greater than those of the plain plug flow.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.2 no.2
• /
• pp.90-93
• /
• 1997

Recombinant exoinulinase was partially purified form the culture supernatant of S.cerevisiae by(NH4)2SO4 precipitation and PEG treatment. The purfied inulinase was immobilized onto Amino-cellulofine with glutaraldeyde as a cross-linking agent. Immobilization yield based on the enzyme activity was about 15%. Optimal pH and temperature of immobilized enzyme were found to be 5.0 and 6$0^{\circ}C$, respectively. The enzyme activity was stably maintained in the pH ranges of 4.5 to 6.0 at 6$0^{\circ}C$. 100% of enzyme activity was observed even after incubation for 24 hr at 6$0^{\circ}C$. In the operation of a packed-bed reactor containing 412U inulinase, dahalia inulin of 7.5%(w/w) concentration was completely hydrolyzed at flow rate of 2.0mL/min at 6$0^{\circ}C$, resulting in a volumetric productivity of 693 g-reducing sugars/L/h. Under the reaction conditions of 1.0mL/min flow rate with 2.5% inulin at 6$0^{\circ}C$, the reactor was successfully operated over 30 days without loss ofinulinase activity.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.16 no.6
• /
• pp.119-133
• /
• 2013

The purpose of this study is to develop riverbed techniques to activating ecological function of hyporheic zone. Hyporheic zone maybe simply defined as an active eco-tone between surface water and groundwater, which facilitates to exchange water, nutrients and aquatic habitat occur in response to variation in discharge and bed geomorphology. The aim of this study is to evaluate the effectiveness of an applied riverbed technique for two years since its installation in the hyporheic zone. The experimental riverbed technique has been implemented on Anyang stream penetrating Anyang city in Gyunggi province. The dimension of the installed structure is 5.0 m in width, 46 m in length. Bottom layer is filled with rip-rap covered with gabion. After the implementation of the technique, the study conducts follow-up monitoring in two years of between 2011 and 2012. The results of follow-up monitoring for two years are as follows:1) In Hydro geomorphic process, the riverbed technique maintains hydraulic stability despite of several flood events in 2011, 2012. 2) After transformation to form pool-and-riffle habitat, for aquatic community composed of freshwater fish, macro invertebrate, and attached algae, the species diversity and population gradually increased. 3) The riverbed technique achieved desired effect on enhancement of ecological function in hyporheic zone.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.4
• /
• pp.375-384
• /
• 2007

Parabolic approximation wave models based on $Pad{\acute{e}}$ approximants are presented of which the $Pad{\acute{e}}$(15, 15) is shown to be applicable to incidence angle $80^{\circ}$ in comparison with the exact solution of a constant sloping bed. After introducing a systematic way of the derivation to the parabolic wave equation, parabolic models are obtained in this study upto the 15th order and several numerical results are given to wave transformation in a constant sloping bed.

• Structural Engineering and Mechanics
• /
• v.61 no.1
• /
• pp.161-169
• /
• 2017

This study aimed to develop a simple and effective method to facilitate the experimental research on mechanical properties of masonry under biaxial compressive stress. A series of tests on full-scale brick masonry panels under biaxial compression have been performed in limited principal stress ratios oriented at various angles to the bed joints. Failure modes of tested panels were observed and failure features were analyzed to reveal the mechanical behavior of masonry under biaxial compression. Based on the experimental data, the failure curve in terms of two orthotropic principal stresses has been presented and the failure criterion of brick masonry in the form of the tensor polynomial has been established, which indicate that the anisotropy for masonry is closely related to the difference of applied stress as well as the orientation of bed joints. Further, compared with previous failure curves and criteria for masonry, it can be found that the relative strength of mortar and block has a considerable effect on the degree of anisotropy for masonry. The test results demonstrate the validity of the proposed experimental method for the approximation of masonry failure under biaxial compressive stress and provide valuable information used to establish experimentally based methodologies for the improvement of masonry failure criteria.

• Journal of Korea Water Resources Association
• /
• v.30 no.5
• /
• pp.495-501
• /
• 1997

Pumping power being given, traditional method requires an iteration process for the solution of discharge and pipe diameter. Yoo and Kang (1996) have developed explicit equations for the estimation of discharge and pipe diameter for the cases of uniformly rough pipe on a sloping bed with a pumping power. The use of poser law for the estimation of friction factor enabled to develop the explicit form of equations. Yoo (1995a) has suggested the mean friction factor method for the estimation of friction factor of commercial pipe or composite surface pipe. With the same approach, the present work has developed the explicit equations of discharge or pipe diameter for the general case of commercial pipe on a sloping bed with a pumping power by adopting the mean friction factor method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.7
• /
• pp.747-754
• /
• 2004

Thermo-fluid characteristics in coke oven, sintering machine and blast furnace in iron-making facility are key processes related to the quality and productivity of the pig iron. Solid material in the processes usually forms a bed in a gas flow. For simulation of the processes by mathematical model, the solid beds are idealized to be a continuum and a reacting solid flow in the gas flow. Governing equations in the form of partial differential equations for the solid material can be constructed based on this assumption. Iron ore sintering bed is simulated and limited amount of parametric study have been performed. The results have a good agreement with the experimental results or physical phenomena, which shows the validity and applicability of the model.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.33 no.2
• /
• pp.325-336
• /
• 2023

With the development of autonomous driving technology, the number of external contact sensors mounted on vehicles is increasing, and the importance is also rising. The vehicular ultrasonic sensor uses the LIN protocol in the form of a bus topology and reports a status message about its surroundings through the vehicle's internal network. Since ultrasonic sensors are vulnerable to various threats due to poor security protocols, physical testing on actual vehicle is needed. Therefore, this paper developed a LIN-CAN co-analysis testbed with a jig for location-specific distance test to examine the operational relation between LIN and CAN caused by ultrasonic sensors.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.639-646
• /
• 2000

Hot air heater with light oil combustion is the most common heater for greenhouse heating in the winter season in Korea. However, since the heat efficiency of the heater is about 80%, considerable unused heat in the form of exhaust gas heat discharges to atmosphere. In order to capture this exhaust gas heat a heat recovery system for plant bed heating in the greenhouse was built and tested in the hot air heating system of greenhouse. The system consists of a heat exchanger made of copper pipes, ${\phi}\;12.7{\times}0.7t$ located inside the rectangular column of $330{\times}330{\times}900mm$, a water circulation pump, circulation plastic pipe and a water tame The total heat exchanger area is $1.5m^2$, calculated considering the heat exchange amount between flue gas and water circulated in the copper pipes. The system was attached to the exhaust gas path. The heat recovery system was designed as to even recapture the latent heat of flue gas when exposing to low temperature water in the heat exchanger. According to performance test it can recover 45,200 to 51,000kJ/hr depending on the water circulation rates of 330 to $690{\ell}$/hr from the waste heat discharged. The exhaust gas temperature left from the heat exchanger dropped to $100^{circ}C$ from $270^{circ}C$ by the heat exchange between the water and the flue gas, while water gained the difference and temperature increased to $38^{circ}C$ from $21^{circ}C$ at the water flow rate of $690{\ell}$/hr. And, the condensed water amount varies from 16 to $43m{\ell}$ at the same water circulation rates. This condensing heat recovery system can reduce boiler fuel consumption amount in a day by 34% according to the feasibility study of the actual mimitomato greenhouse. No combustion load was observed in the hot air heater.