• Structural Engineering and Mechanics
• /
• 제74권4호
• /
• pp.457-470
• /
• 2020

The force resisting ability of a connection has direct implications on the overall response of a timber framed structure to various actions, thereby governing the integrity and safety of such constructions. The behavior of timber framed structures has been studied by many researchers by testing full-scale-connections in timber frames so as to establish consistent design provisions on the same. However, much emphasis in this approach has been unidirectional, that has focused on a particular connection configuration, with no research output stressing on the refinement of the existing connection details in order to optimize their performance. In this regard, addition of adhesive to dowelled timber connections is an economically effective technique that has a potential to improve their performance. Therefore, a comparative study to evaluate the performance of various full-scale timber frame Nailed connections (Bridled Tenon, Cross Halved, Dovetail Halved and Mortise Tenon) supplemented by adhesive with respect to Nailed-Only counterparts under tensile loading has been investigated in this paper. The load-deformation values measured have been used to calculate stiffness, load capacity and ductility in both the connection forms (with and without adhesion) which in turn have been compared to other configurations along with the observed failure modes. The observed load capacity of the tested models has also been compared to the design strengths predicted by National Design Specifications (NDS-2018) for timber construction. Additionally, the experimental behavior was validated by developing non-linear finite element models in ABAQUS. All the results showed incorporation of adhesive to be an efficient and an economical technique in significantly enhancing the performance of various timber nailed connections under tensile action. Thus, this research is novel in a sense that it not only explores the tensile behavior of different nailed joint configurations common in timber construction but also stresses on improvising the same in a logical manner hence making it distinctive in its approach.

• Smart Structures and Systems
• /
• 제1권1호
• /
• pp.83-101
• /
• 2005

This paper summarizes the application of a rational methodology for the structural assessment of older reinforced concrete Tunisian bridges. This methodology is based on ambient vibration measurement of the bridge, identification of the structure's modal signature and finite element model updating. The selected case study is the Boujnah bridge of the Tunis-Msaken Highway. This bridge is made of a continuous four-span simply supported reinforced concrete slab without girders resting on elastomeric bearings at each support. Ambient vibration tests were conducted on the bridge using a data acquisition system with nine force-balance accelerometers placed at selected locations of the bridge. The Enhanced Frequency Domain Decomposition technique was applied to extract the dynamic characteristics of the bridge. The finite element model was updated in order to obtain a reasonable correlation between experimental and numerical modal properties. For the model updating part of the study, the parameters selected for the updating process include the concrete modulus of elasticity, the elastic bearing stiffness and the foundation spring stiffnesses. The primary objective of the paper is to demonstrate the use of the Enhanced Frequency Domain Decomposition technique combined with model updating to provide data that could be used to assess the structural condition of the selected bridge. The application of the proposed methodology led to a relatively faithful linear elastic model of the bridge in its present condition.

• Computers and Concrete
• /
• 제22권3호
• /
• pp.279-289
• /
• 2018

Shear walls are one of the important structural elements for bearing loads imposed on buildings due to winds and earthquakes. Composite shear walls with high lateral resistance, and high energy dissipation capacity are considered as a lateral load system in such buildings. In this paper, a composite shear wall consisting of steel faceplates, infill concrete and tie bars which tied steel faceplates together, and concrete filled steel tubular (CFST) as boundary columns, was modeled numerically. Test results were compared with the existing experimental results in order to validate the proposed numerical model. Then, the effects of some parameters on the behavior of the composite shear wall were studied; so, the diameter and spacing of tie bars, thickness and compressive strength of infill concrete, thickness of steel faceplates, and the effect of strengthening the bottom region of the wall were considered. The seismic behavior of the modeled composite shear wall was evaluated in terms of stiffness, ductility, lateral strength, and energy dissipation capacity. The results of the study showed that the diameter of tie bars had a trivial effect on the performance of the composite shear wall, but increasing the tie bars spacing decreased ductility. Studying the effect of infill concrete thickness, concrete compressive strength, and thickness of steel faceplates also showed that the main role of infill concrete was to prevent buckling of steel faceplates. Also, by strengthening the bottom region of the wall, as long as the strengthened part did not provide a support performance for the upper part, the behavior of the composite shear wall was improved; otherwise, ductility of the wall could be reduced severely.

• Structural Engineering and Mechanics
• /
• 제23권6호
• /
• pp.615-634
• /
• 2006

Seismic response of the liquid storage tanks isolated by the elastomeric bearings and sliding systems is investigated under near-fault earthquake motions. The fault normal and parallel components of near-fault motion are applied in two horizontal directions of the tank. The continuous liquid mass of the tank is modeled as lumped masses known as sloshing mass, impulsive mass and rigid mass. The corresponding stiffness associated with these lumped masses has been worked out depending upon the properties of the tank wall and liquid mass. It is observed that the resultant response of the isolated tank is mainly governed by fault normal component with minor contribution from the fault parallel component. Further, a parametric study is also carried out to study the effects of important system parameters on the effectiveness of seismic isolation for liquid storage tanks. The various important parameters considered are: aspect ratio of tank, the period of isolation and the damping of isolation bearings. There exists an optimum value of isolation damping for which the base shear in the tank attains the minimum value under near-fault motion. The increase of damping beyond the optimum value will reduce the bearing and sloshing displacements but increases the base shear. A comparative performance of five isolation systems for liquid storage tanks is also studied under normal component of near-fault motion and found that the EDF type isolation system may be a better choice for design of isolated tank in near-fault locations. Finally, it is also observed that the satisfactory response can be obtained by analysing the base-isolated tanks under simple cycloidal pulse instead of complete acceleration history.

• 한국지진공학회논문집
• /
• 제2권2호
• /
• pp.13-22
• /
• 1998

본 연구는 지진격리장치의 일종인 마찰 단진자 시스템(FPS)의 교량에의 적용에 관한 연구이다. FPS에 의하여 지진 격리된 교량과 지진 격리되지 않은 교량의 지진하중 작용시의 응답을 비교하기 위하여 축소모델 교량을 이용한 진동대 실험을 수행하였다. 연구결과, 본 장치를 설치한 경우 지진하중에 대한 지지능력이 향상하는 것으로 나타났다. 또한, 활동면 곡류반경에 의해 조절이 가능한 F.P.S 베어링의 강성은 입력된 kwlsfur의 강도와는 무관하며, 활동면의 마찰계수에 따라 속도가 변화하여 약진시에는 활동면에서의 속도가 작으므로 강진시와 비교하여 지진하중에 의하여 발생하는 마찰력도 감소하게 되었다. 한편 F.P.S 베어링의 마찰특성은 반복된 실험에서도 변화하지 않았고, 영구변형은 약적으로도 작았을 뿐만 아니라 누적되지도 않았다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.41-44
• /
• 2008

PCT는 장경간 가시설 벽체를 지지하는 써포트 구조물을 프리캐스트 방식으로 공장에서 미리 제작하고, 콘크리트 소재로 구성하여 강성을 만족시킬 수 있도록 그 구조가 개선된 프리캐스트 가시설 구조체이다. 그것의 부재들은 공장에서 미리 정형화된 형태로 제작되고 가시설 벽체의 내측면에 고정수단을 매개로 근접되게 배치된다. PCT system은 내부에 콘크리트가 충진되는 세그먼트 부재들의 단부와 접촉되어 결합수단을 매개로 일체화되어 또한 다른 세그먼트 부재를 연결시키는 연결구로 이루어진 써포트 구조물로 구성된 것이다. 본 연구는 전체적인 길이가 긴 장경간 가시설 벽체에 대한 충분한 지지력을 얻을 수 있을 뿐만 아니라, 프리캐스트 방식으로 제작되어 콘크리트 양생에 소요되는 시간을 단축시킬 수 있으므로 시공기간이 단축되는 등의 유용한 효과를 갖는다.

• Earthquakes and Structures
• /
• 제18권5호
• /
• pp.527-542
• /
• 2020

In traditional eccentrically braced steel frames, damages and plastic deformations are limited to the links and the main structure members are required tremendous sizes to ensure elasticity with no damage based on the force-based seismic design method, this limits the practical application of the structure. The high strength steel frames with eccentric braces refer to Q345 (the nominal yield strength is 345 MPa) steel used for links, and Q460 steel utilized for columns and beams in the eccentrically brace steel frames, the application of high strength steels not only brings out better economy and higher strength, but also wider application prospects in seismic fortification zone. Here, the structures with four type eccentric braces are chosen, including K-type, Y-type, D-type and V-type. These four types EBFs have various performances, such as stiffness, bearing capacity, ductility and failure mode. To evaluate the seismic behavior of the high strength steel frames with variable eccentric braces within the similar performance objectives, four types EBFs with 4-storey, 8-storey, 12-storey and 16-storey were designed by performance-based seismic design method. The nonlinear static behavior by pushover analysis and dynamic performance by time history analysis in the SAP2000 software was applied. A total of 11 ground motion records are adopted in the time history analysis. Ground motions representing three seismic hazards: first, elastic behavior in low earthquake hazard level for immediate occupancy, second, inelastic behavior of links in moderate earthquake hazard level for rapid repair, and third, inelastic behavior of the whole structure in very high earthquake hazard level for collapse prevention. The analyses results indicated that all structures have similar failure mode and seismic performance.

• 한국지반공학회논문집
• /
• 제21권2호
• /
• pp.67-84
• /
• 2005

본 연구는 포화된 연약 점성토에 대한 보강효과를 분석하기 위하여 롤러 다짐장비를 사용하여 수행하였다. 시료는 12시간 수침으로 포화 상태를 만들었으며, 철재 롤러로 평면변형을 상태에서 5cm 층 두께로 4층의 다짐을 실시하였다. 보강효과를 분석하기 위하여 무보강 조건 및 부직포와 직포로 구성된 복합보강재를 사용한 보강조건으로 다짐 공시체를 제작하였다. 복합보강재의 배수효과와 인장 보강효과로 고함수비 점성토의 지지력을 증가시켜, 보강토에 대하여 큰 다짐하중을 가할 수 있게 되어 보다 큰 밀도를 효과적으로 얻을 수 있다. 또한 다짐 작업시 보강재에 의해 연직재하 하중에 대한 전단저항 반력의 감소에 의해 다짐효율을 증가시킨다. 공시체 저면에서의 최대 연직응력은 다짐두께가증가 할수록 감소하게 된다. 한편 보강재는 롤러의 연직하부의 지반강성을 증가시켜 응력집중현상이 발생한다. 이로인하여 공시체 저면에서 보다 높은 연직응력 수준을 유지하며 보다 효과적인 다짐 특성을 제공하게 된다. 시험결과로부터 연약점성토의 효과적인 다짐을 위해서는 보강재가 필수적으로 요구된다고 할 수 있다.

• 한국지반환경공학회 논문집
• /
• 제17권3호
• /
• pp.5-12
• /
• 2016

쇄석말뚝공법은 비교적 강성이 크고 압축성이 작은 쇄석을 연약한 점성토 지반 및 느슨한 사질토 지반에 치환 후 다져 시공함으로써 연약한 지반의 지지력 증가와 침하량 감소, 압밀배수에 의한 지반개량 효과에 더불어 사질토 지반에서는 지진 발생시 액상화 방지에 효과적인 공법이다. 쇄석말뚝공법은 여러 토목분야에서 활용되고 국제적으로 상당히 많은 시공실적을 보이고 있으나, 아직까지 정형화된 침하량 산정방법은 없다. 따라서 본 연구에서는 쇄석말뚝공법의 합리적인 침하량을 예측하기 위하여 기존에 제안되어 사용되고 있는 침하량 이론식들을 비교 분석하여 적용성을 평가하였다. 그 결과 Hook's law 식이 수치해석과 가장 근접하는 것으로 확인되었다.

• 한국지반신소재학회논문집
• /
• 제10권3호
• /
• pp.33-41
• /
• 2011

본 논문에서는 국내 건설현장 29개 지점에서 국내 철도노반 다짐품질관리 방법인 반복평판재하시험과 LFWD(Light Falling Weight Deflection)에서 구한 변형률계수(Ev2)와 변형계수($E_{LFWD}$)에 대하여 응력보정을 통해 자갈재료와 사질토에 대하여 상관성을 비교하였다. 실험결과 대부분 다짐품질관리 기준을 만족하고 있으며, 입상재료의 경우 관리기준치에 약 3배이상 값을 나타내었다. 두 시험방법에 따른 상관성은 토사의 경우에는 서로 상관성이 높은 것으로 나타났지만, 강성이 상대적으로 큰 입상재료의 경우 두 시험간의 상관성이 적은 것으로 나타났다. 또한, 시험방법 별로 탄성계수를 구하여 응력상태를 보정한 후 회귀 분석한 결과 응력 보정하지 않는 조건보다 상관성이 더 높게 나타났다.