• Journal of the Korean Geotechnical Society
• /
• v.37 no.7
• /
• pp.13-23
• /
• 2021

If roads, bridges, buildings, etc. are built on the ground with soft clay or organic soil, there may be a lot of problems in geotechnical engineering such as settlement and stability due to the large settlement and lack of bearing capacity. In extreme cases, it may appear due to shear failure or collapse of the constructed structure, so a ground improvement method is indispensable to increase the strength of the ground and to suppress settlement. In this study, the settlement according to each groundwater level condition was analyzed using the measurement results for the groundwater level conditions, one of the important factors in predicting the settlement in dredged and reclaimed ground, and the groundwater level conditions applied to the settlement analysis were proposed by comparing it with settlement generated 5 years after construction. As a result of the analysis, it is judged that it is reasonable to apply the measured groundwater level during construction and the low water ordinary neap tide (L.W.O.N.T) during load application for the groundwater level in the settlement analysis. In addition, in the case of the dredged and reclaimed ground, it is estimated that the water pressure acting on the clay layer is nonlinear, as the result of the observations of the head of water at the observation points above and below the in-situ clay layer were different.

• Tribology and Lubricants
• /
• v.35 no.1
• /
• pp.44-51
• /
• 2019

The paper presents the rotordynamic performance measurements and model predictions of a fuel cell electric vehicle (FCEV) air compressor supported on gas foil bearings (GFBs). The rotor has an impeller on one end and a thrust runner on the other end. The front (impeller side) and rear (thrust side) gas foil journal bearings (GFJBs) are located between the impeller and thrust runner to support the radial loads, and a pair of gas foil thrust bearings are located on both sides of the thrust runner to support the axial loads. The test GFJBs have a partial arc shim foil installed between the top foil and bump strip layers to enhance hydrodynamic pressure generation. During the rotordynamic performance tests, two sets of orthogonally installed eddy-current displacement sensors measure the rotor radial motions at the rotor impeller and thrust ends. A series of speed-up and coast-down tests to 100k rpm demonstrates the dominant synchronous (1X) rotor responses to imbalance masses without noticeable subsynchronous motions, which indicates a rotordynamically stable rotor-GFB system. Finite element analysis of the rotor determines the rotor free-free (bending) natural modes and frequencies well beyond the maximum rotating frequency. The predicted damped natural frequencies and damping ratios of the rotor-GFB system reveal rotordynamic stability over the speeds of interest. The imbalance response predictions show that the predicted critical speeds and rotor amplitudes strongly agree with the test measurements, thus validating the developed rotordynamic model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.638-644
• /
• 2019

In this study, the fluid flow and heat transfer characteristics within sandwich panels are investigated using computational fluid dynamics. Within the sandwich panels having periodic cellular cores, air can freely move inside the core section so that the structure is able to perform multi-functional roles such as simultaneous load bearing and heat dissipation. Thus, there needs to examine the thermal and flow analysis with respect to design variables and various conditions. In this regard, ANSYS Fluent was utilized to explore the flow and heat transfer within the pyramidal truss sandwich structures by varying the truss angle and inlet velocity. Without the entry effect in the first unitcell, the constant rate of pressure and the constant rate of Nusselt number was observed. As a result, it was demonstrated that Nusselt number increases and friction factor decreases as the inlet velocity increases. Moreover, the rate of Nusselt number and friction factor was appreciable in the range of V=1-5m/s due to the transition from laminar to turbulent flow. Regarding the effect of design variable, the variation of truss angle did not significantly influence the characteristics.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.8-15
• /
• 2019

In this study, we synthesized a calcium sulfonate complex grease and a lithium complex grease to investigate their physical, rheological and tribological properties. The thermal stability of the calcium sulfonate was higher than $300^{\circ}C$ and the lithium complex grease was $245^{\circ}C$ in the dropping point test. In the grease viscosity measurement, the calcium sulfonate complex grease was measured as $7.0Pa{\cdot}s$ and the lithium complex grease was as $4.5Pa{\cdot}s$. Therefore, it was confirmed that the calcium sulfonate complex grease is superior to the lithium complex grease in terms of thermal stability and cohesiveness. In the 4-ball wear test, the calcium sulfonate complex grease was measured to be 0.43 mm and the lithium complex grease to 0.85 mm. In the 4-ball extreme pressure test, calcium sulfonate complex grease was measured as 620 kgf and the lithium complex grease was as 125 kgf. Therefore, it was confirmed that the calcium sulfonate complex grease is superior to the lithium complex grease in abrasion resistance and load-bearing property. It was found that the calcium sulfonate complex grease is more effective than the lithium complex grease in the lubrication at high temperature and high load.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.9
• /
• pp.33-40
• /
• 2023

The lateral load which is applied to the pile foundation supporting the superstructure during an earthquake is divided into the inertia force of the upper structure and the kinematic force of the ground. The inertia force and the kinematic force could cause failure to the pile foundation through different complex mechanisms. So it is necessary to predict and evaluate interaction of the ground-pile-structure properly for the seismic design of the foundation. The interaction is affected by the lateral behavior of the structure, the length of the pile, the boundary conditions of the head, and the relative density of the ground. Confining pressure and ground stiffness change accordingly when the relative density changes, and it results that the coefficient of subgrade reaction varies depending on each system. Horizontal bearing behavior and capacity of the pile foundation vary depending on lateral load condition and relative density of the sandy soil. Therefore, the 1g shaking table tests were conducted to confirm the effect of the relative density of the dried sandy soil to dynamic behavior of the group pile supporting the superstructure. The result shows that, as the relative density increases, maximum acceleration of the superstructure and the pile cap increases and decreases respectively, and the slope of the p-y curve of the pile decreases.

• Geomechanics and Engineering
• /
• v.37 no.6
• /
• pp.599-614
• /
• 2024

To evaluate the safety status of deteriorated segments in a submarine shield tunnel during its service life, a seepage model was established based on a cross-sea shield tunnel project. This model was used to study the migration patterns of erosive ions within the shield segments. Based on these laws, the degree of deterioration of the segments was determined. Using the derived analytical solution, the internal forces within the segments were calculated. Lastly, by applying the formula for calculating safety factors, the variation trends in the safety factors of segments with different degrees of deterioration were obtained. The findings demonstrate that corrosive seawater presents the evolution characteristics of continuous seepage from the outside to the inside of the tunnel. The nearby seepage field shows locally concentrated characteristics when there is leakage at the joint, which causes the seepage field's depth and scope to significantly increase. The chlorine ion content decreases gradually with the increase of the distance from the outer surface of the tunnel. The penetration of erosion ions in the segment is facilitated by the presence of water pressure. The ion content of the entire ring segment lining structure is related in the following order: vault < haunch < springing. The difference in the segment's rate of increase in chlorine ion content decreases as service time increases. Based on the analytical solution calculation, the segment's safety factor drops more when the joint leaks than when its intact, and the change rate between the two states exhibits a general downward trend. The safety factor shows a similar change rule at different water depths and continuously decreases at the same segment position as the water depth increases. The three phases of "sudden drop-rise-stability" are represented by a "spoon-shaped" change rule on the safety factor's change curve. The issue of the poor applicability of indicators in earlier studies is resolved by the analytical solution, which only requires determining the loss degree of the segment lining's effective bearing thickness to calculate the safety factor of any cross-section of the shield tunnel. The analytical solution's computation results, however, have some safety margins and are cautious. The process of establishing the evaluation model indicates that the secondary lining made of molded concrete can also have its safety status assessed using the analytical solution. It is very important for the safe operation of the tunnel and the safety of people's property and has a wide range of applications.

• Journal of Preventive Medicine and Public Health
• /
• v.32 no.3
• /
• pp.383-394
• /
• 1999

Objectives: This study was conducted to identify the factors influencing the mortality of Koreans over the age of 40 by a nested case-control study. Methods: The cohort consisted of the beneficiaries of Korea Medical Insurance Corporation for Government Employees & Private School Teachers and Staff(KMIC) who received health examinations of KMIC in 1992 and 1993 retrospectively. At that time, they were more than 40 years old. The cases were 19,258 cohort members who had died until December 31, 1997. The controls were 19,258 cohort members who were alive until December 31, 1997. Controls were matched with age and sex distribution of the cases. The data used in this study were the funeral expenses requesting files, and the files of health examinations and health questionnaires gathered in 1992 and 1993. To assess the putative risk factors of death, student t-test, chi-square test, multiple logistic regression analysis were used. Results : In multiple logistic regression analysis, independent risk factors of death were as follows; systolic blood pressure, diastolic blood pressure, blood glucose, AST, urine glucose, urine protein, alcohol drinking(frequency), cigarette smoking and perceived health status, intake of restoratives and blood transfusion showed positive associations with death; coffee consumption showed negative associations with death; and body mass index and serum total cholesterol showed J-shaped association with death. Conclusions: Regarding the direction of association, the result of analysis on the data restricted to '96-'97 was same as that of '93-'97. But in some variables such as obesity, serum cholesterol, the odds ratios of death in the data of '96-'97 were higer than those of '93-'94, which suggested that the data of '93-'94 was bearing effect-cause relationship. We concluded that it suggested further researches using long-term follow-up data to be needed in this area.

• Economic and Environmental Geology
• /
• v.22 no.4
• /
• pp.303-314
• /
• 1989

The electrum-silver-sulfide mineralization of the Geojae island area was deposited in three stages (I, II, and carbonate) of quartz and calcite veins that crosscut Late Cretaceous volcanic rocks and granodiorite(83 m.y.). Stages I and II were terminated by the onset of fractunng and breCCIation events. Fluid inclusion data suggest that the gold-sulfide-bearing stages I and II each evolved from an initial high temperature( near $370^{\circ}C$) to a later low temperature(near $200^{\circ}C$). Each of those stages represented a separate mineralizing system which cooled prior to the onset of the next stage. The relationship between homogenization temperature and salinity in stages I and II suggests a complex history of boiling, cooling and dilution. Evidence of boiling indicates a pressure of < 100 bars, corresponding to a depth of 500 to 1,250m assummg hthostatlc and hydrostatic pressure regimes, respectively. Fluid inclusion and mineralogical evidence suggest that the electrum-silver mineralization was deposited at a temperature of $220-260^{\circ}C$ from ore fluids with salinities between 1.9 and 8.1 equivalent wt.% NaCl. Total sulfur concentration is estimated to be $10^{-3}$ to $10^{-4}$ molal. The estimated $fs_2$ and $fo_2$ range from $10^{-11.8}$ to $10^{-14}$ atm and $10^{-35}$ to $10^{-36}$ atm, respectively. The chemical conditions indicate that the dominant sulfur species in the ore forming fluids was a reduced form($H_2S$). Rapid cooling and dilution of ore-forming fluids by mixing with less-evolved meteoric waters led to gold-silver deposition through the breakdown of the bisulfide complex($Au(HS)_2$) as the activity of $H_2S$ decreased.

• Journal of the Korean Home Economics Association
• /
• v.5 no.1
• /
• pp.733-739
• /
• 1966

A 371 agricultural households from 26 different communities in South Korea was subjected on a study of food taboos in January of 1966. To the pregnant women, those to whom a high protein diet is particurally important, as many as 14 different kinds of foods, mostly portein rich foods, were avoided to eat. It is believed that if duck is eaten while pregnant her baby may walk like a duck in later life. Some mother have a strong aversion to the rabbit meat that her unborn baby must be a harelip. It is feared to eat chicken, shark or carp by the pregnant mother for her baby may get a gooseflesh appearance, or fish scale-like skin in later life. It is thought that if mother eats soup made of meat borns, especially chicken bones, a disfigured baby may be born. Some area informed that if mother eats crab meat her future baby will always bubble. To the child-bearing mothers 13 different kinds of foods were avoided to eat. Some believe that if raddish kimchi, soybean curd, squash are eaten while dilivery that mother may get dental decay or to lose all her teeth. Other think that highly spiced raddish kimchi cause delivery difficult. To the lactating mothers 7 different items of foods were not recommended to eat. It is a common belief that eating green vegetables, especially fresh lettuce, are restricted that her baby may stool greenish. It is said that eating ginsen-chicken soup, or ginsen tea during lactating reduces breast milk secretion. To the weaning babies 7 different kinds of foods were prohibited to fee. Eggs are not eaten because mothers think her babies will start to talk very late. Eight different items of foods in cases of gastro-intestinal diseases, 5 items for liver disease, 7 items for high blood pressure as well as for paralysis were respectively restricted. It is said that meats including pork, beef, and chicken are neither desirable for the patients of high blood pressure nor those of paralysis. To the measles children 10 varieties of foods were restricted. Especially soybean products and meats were not encouraged to use for avoiding asecond attack of measles. For the common cold 8 different kinds of foods were aversed and men think that eating of soup of undria delays a recovery. For the tuberculosis 4 kinds of foods were prohibited to eat. It is said that wine, red pepper and ginsen will stimulate lung bleeding. Many mothers had a strong aversion to fermented shrimp and fish in case of style. and 5 different items of foods were restricted. In case of menstration not so many foods were restricted as other cases, but meat soup is not eaten in this condition in some areas. Majority of food taboos in Korean villages are neither based on tribal nor religious factors. But no one knows how, since what ages, from where, these food taboos have been transmitted and spread over the country. This survey found a great variety of food taboos, aversions, traditional beliefs and prohibitions latent unknown reseasons, or non-scientific conceptions, or completely different ideas from the modern medical aspect, or somewhat fallacious and superstitious beliefs. For the vascular disease contrasting approach were found between modern the oritical therapy and popular remedy among the rural populations who largely depend on the eastern medication. Further scientific study on either side should be done to lead the patient proper way. Many restricted foods such as rabbit, duck, chicken and fish are best resources of protein rich foods which are available in the village. Emphasis should be laid upon breaking down fallacious and supersititious food taboos through the extended nutrition education activities in order to improve food habit and good eating pattern for healthier and stronger generations of Korea.

• Economic and Environmental Geology
• /
• v.19 no.3
• /
• pp.199-218
• /
• 1986

Arsenopyrite in arsenic and polymetallic ores from calcic Fe-W skarn deposit of the Ulsan mine, Republic of Korea, has been investigated by means of electron microprobe analysis and X-ray diffractometry. As a result, it is revealed that the Ulsan arsenopyrite may be classified into the following three species with different generation on the basis of its mode of occurrence, chronological order during polymetallic mineralization and chemical composition; arsenopyrites I, II and III. 1) Arsenopyrite I-(Ni, Co)-bearing species belonging to the oldest generation, which has crystallized together with (Ni, Co)-arsenides and -sulpharsenides in the early stage of polymetallic mineralization. In rare cases, it contains a negligible amount of antimony. It occurs usually as discrete grains with irregular outline, showing rarely subhedral form, and is diffused in skarn zone. The maximum contents of nickel and cobalt are 10.04 Ni and 2.45 Co (in weight percent). Occasionally, it shows compositional zoning with narrow rim of lower (Ni+Co) content. 2) Arsenopyrite II-arsenian species, in which (Ni+Co) content is almost negligible, may occur widely in arsenic ores, and its crystallization has followed that of arsenopyrite I. It usually shows subhedral to euhedral form and is closely associated with $l{\ddot{o}}llingite$, bismuth, bismuthinite, chalcopyrite, sphalerite, bismuthian tennantite, etc. It is worthy of note that arsenopyrite II occasionally contains particles consisting of both bismuth and bismuthinite. 3) Arsenopyrite III-(Ni, Co)-free, S-excess and As-deficient species is close to the stoichiometric composition, FeAsS. It occurs in late hydrothermal veins, which cut clearly the Fe-W ore pipe and the surrounding skarn zone. It shows euhedral to subhedral form, being extremely coarse-grained, and is closely associated with pyrite, "primary" monoclinic pyrrhotite, galena, sphalerite, etc. Among three species of the Ulsan arsenopyrite, arsenopyrite I does not serve as a geothermometer, because (Ni+Co) content always exceeds 1 weight percent. In spite of the absence of Fe-S minerals as sulphur-buffer assemblage, the presence of $Bi(l)-Bi_2S_3$ sulphur-buffer enables arsenopyrite II to apply successfully to the estimation of either temperature and sulphur fugacity, the results are, $T=460{\sim}470^{\circ}C$, and log $f(S_2)=-7.4{\sim}7.0$. With reference to arsenopyrite III, only arsenopyrite coexisting with pyrite and "primary" monoclinic pyrrhotite may serve to restrict the range of both temperature and sulphur fugacity, $T=320{\sim}440^{\circ}C$, log $f(S_2)=-9.0{\sim}7.0$. These temperature data are consistent with those obtained by fluid inclusion geothermometry on late grandite garnet somewhat earlier than arsenopyrite II. At the beginning of this paper, the geological environments of the ore formation at Ulsan are considered from regional and local geologic settings, and physicochemical conditions are suspected, in particular the formation pressure (lithostatic pressure) is assumed to be 0.5kb (50MPa). The present study on arsenopyrite geothermometry, however, does not bring about any contradictions against the above premises. Thus, the following genetical view on the Ulsan ore deposit previously advocated by two of the present authors (Choi and Imai) becomes more evident; the ore deposit was formed at shallow depth and relatively high-temperature with steep geothermal gradient-xenothermal conditions.