• 수산해양기술연구
• /
• 제23권4호
• /
• pp.157-162
• /
• 1987

장어통발의 P.P깔때기 살과 대나무 깔때기 살의 탄성을 측정하고 측면 구멍을 막은 통발과 원형의 유수저항, 침강시간 및 미끼의 냄새확산 등을 관찰한 다음 해상어획 시험을 행한 결과는 다음과 같다. 1. P.P 깔때기 살의 탄성은 대나무 살보다 훨씬 작고, 하중이 증가할수록 탄성회복도는 감소하였다. 2. 플라스틱 장어통발의 유수저항 R(kg)는 유속 V(m/sec)에 따라 다음 관계식으로 나타낼 수 있다. R=0.36V 상(2.01) 3. 장어통발의 침강시간은 측면 구멍을 막은 경우 수면상에서의 완전 침수까지 1~2초 정도 원형보다 지연되나 그 후의 침강속도는 거의 차이가 없었다. 4. 통발 내의 미끼 수용액은 측면 구멍을 많이 막을수록 원형보다 입구쪽으로 집중되어 확산되었다. 5. 측면 구멍을 일부 막은 통발과 원형을 가지고 어획시험을 한 결과 통발당 평균 어획미수나 평균어획량의 어획성능에 있어서 뻘로 된 어장에서는 차이가 없는 것 같다.

• 한국공간구조학회논문집
• /
• 제8권2호
• /
• pp.73-84
• /
• 2008

지진에 의한 구조물의 응답을 저감시키기 위하여 내진, 면진, 제진 등 다양한 장치가 사용되고 있으며 그 중에서 면진장치는 구조물로 전달되는 지진에너지를 최소화하기 위한 시스템으로 그 주된 목적은 구조물의 주기를 길게 만들어 지진파의 탁월주기를 벗어나게 하는 것이다. 본 연구에서는 대공간구조물의 기본적인 동적특성을 가지고 있으며 동시에 가장 간단한 구조이기도 한 아치에 납-고무면진장치와 마찰진자면진장치를 적용하여 지진거동을 분석하였다. 대공간구조물의 지진거동은 일반적인 골조구조물의 지진거동과 달리 수평지진에 의하여 수직방향으로 큰 지진응답이 나타나고 있다. 면진장치를 대공간 구조물에 적용할 경우에 수평지진하중에 의하여 수평방향 지진응답이 저감되는 것은 물론 면진장치의 수직강성으로 인하여 수직응답도 현저하게 저감되는 것을 알 수 있었다.

• 콘크리트학회논문집
• /
• 제12권5호
• /
• pp.35-46
• /
• 2000

In this paper, an analytical model is proposed to predict the shear strenth of RC beams strengthened by FRP. This predictional model is composed of two basic models-the upper bound theorem for shear failure (shear tension or shear compression criteria) and a truss model based on the lower bound theorem for diagonal tension creteria. Also, a simple flexural theory based on USD is used to explain flexural failure. The major cause of destruction of RC beams shear strengthened by FRP does not lie in FRP fracture but in the loss of load capacity incurred by rip-off failure of shear strengthening material. Since interfacial shear stree between base concrete and the FRP is a major variable in rip-off failure mode, it is carefully analyzed to derive the shear strengthening effect of FRP. The ultimate shear strength and failure mode of RC beams, using different strengthening methods, estimated in this predictional model is then compared with the result derived from destruction experiment of RC beams shear strengthened using FRP. To verify the accuracy and consistency of the analysis, the estimated results using the predictional model are compared with various other experimental results and data from previous publications. The result of this comparative analysis showed that the estimates from the predictional model are in consistency with the experimental results. Therefore, the proposed shear strength predictional model is found to predict with relative accuracy the shear strength and failure mode of RC beams shear strengthened by FRP regardless of strengthening method variable.

• 건축역사연구
• /
• 제21권3호
• /
• pp.7-28
• /
• 2012

This study is intended to Mindori structure which is general private houses' structural type among traditional types and is a basic study to confirm structural characteristics of Hwatong connection which is general connection type of column-beam-cross beam. It is aimed to analyze how main member, column, such as size, figure, thickness of Sungetuk and Dugeup affect on structure. Following conclusions are drawn. 1. According to connection conditions, models with big coefficient of friction show stable hysteretic behavior until the angle rotation of member reaches 1/60 and models with small coefficient of friction show dramatical increase in load after the angle rotation of member reaches 1/24. After the angle rotation of member reaches 1/30, separation distance of members is identified physically and cracks are not observed. 2. Specimens with big coefficient of friction show similar inner force regardless of column size(except column size 150mm) and models with small coefficient of friction show increasing inner force as the column size increases. Specimens with same sectional area have similar inner force even though the column figures are different. The thickness of Sungetuk and Dugeup doesn't affect inner force greatly, however, when the thickness of Sungetuk is thin, it could lead to failure of structure as it breaks. 3. The bigger the size of column and the coefficient of friction are, the smaller Bending stiffness depreciation ratio is. 4. Energy Dissipation Efficiency differs from the coefficient of friction. When the coefficient of friction is big, square column shows bigger than round one and it is bigger when the thickness of Sungetuk and Dugeup is thicker. When the coefficient of friction is small, round column shows bigger than square one.

• 한국지반공학회논문집
• /
• 제31권10호
• /
• pp.61-76
• /
• 2015

최근 지반공학 분야에서는 깊은기초와 얕은기초에 관한 한계상태설계법에 관한 연구가 선행되고 있으며, 옹벽구조물에 관한 연구는 미미한 실정이다. 본 연구는 철도 옹벽의 한계상태설계법을 도입하기 위한 기초 연구로써 옹벽 표준도의 파괴모드별 신뢰도지수가 목표신뢰도지수를 만족하는지를 평가하였으며, 옹벽 표준도에 대한 하중저항계수 설계를 수행함으로써 한계상태설계법의 적용성을 분석하였다. 철도 옹벽 표준도의 일부는 활동 및 지지력파괴에 대한 신뢰도지수가 목표신뢰도지수에 미달하며, 하중저항계수설계법에 의한 한계상태를 만족하지 못하여 한계상태설계 도입 시 철도 옹벽 표준도의 수정이 필요한 것으로 평가되었다.

• 한국수소및신에너지학회논문집
• /
• 제27권4호
• /
• pp.357-364
• /
• 2016

Recently, the world faces the environmental problem such as air pollution due to harmful gas discharged from car and abnormal climate due to the green-house gases increased by the discharge of $CO_2$. Compressed Natural Gas (CNG), one of alternative for this problem, is less harmful, compared to the existing fossil fuel, as gaseous fuel, and less carbon in fuel ingredients and carbon dioxide generation rate relatively favorable more than the existing fuel. However, CNG fuel has the weakness of slow flame propagation speed and difficult fast burn. On the other hand, hydrogen does not include carbon in fuel ingredients, and does not discharge harmful gas such as CO and HC. Moreover, it has strength of quick burning velocity and ignition is possible with small ignition energy source and it's has wide Lean Flammability Limit. If using this hydrogen with CNG fuel, the characteristics of output and discharge gas is improved by the mixer's burning velocity improved, and, at the same time, is possible to have stable lean combustion with the reduction of $CO_2$ expected. Therefore, this research tries to identify the characteristics of engine and emission gas when mixing CNG fuel and hydrogen in each portion and burning them in spark igniting engine, and grasp the combustion stability and emission gas characteristics according and use it as the basic data of hydrogen-CNG premixed engine.

• 대한치과보철학회지
• /
• 제27권2호
• /
• pp.261-270
• /
• 1989

Bend test is one of the methods comparing the physical properties of the clasp wires. The type of bend test used in this investigation was the cantilever loading of a wrought wire. The purpose of this study was to compare the flexibility of a number of commonly used clasp wires, in according to gauge, alloy and heat treatment, under specific condition of load and deflection. Seven noble and one base metal wires were tested under three conditions as follows: (1) as received, (2) quenched (placed in an over at $700^{\circ}C$ for ten minutes and immediately quenched in water at room temperature.), (3) oven cooled (quencned as described, then placed in an oven at $450^{\circ}C$ for two minutes and uniformly slowly cooled to $250^{\circ}C$ in thirty minutes.) The basic test specimen consists of a sample 25 mm in length and 19, 18 gauge in diameter (17 gauge also in two alloys), and the wire was loaded in the form of straight cantilever beams. Force at 0.25 mm (0.01 inch) and 0.5 mm (0.02 inch) deflections for all samples were recorded. The results were as follows ; 1. Ticonium was least flexible and No. 2 was most flexible in according to gauge, alloy and heat treatment. 2. In most of precious wrought wire, the flexibility was increased, but there was no statistically significant differences between as-received and softened condition. 3. There was no statistically differences between as-received and hardened condition. 4. For each alloy, there were statistically significant differences in flexibility due to clasp diameter.

• The Journal of Advanced Prosthodontics
• /
• 제3권3호
• /
• pp.113-118
• /
• 2011

PURPOSE. The objective of the present study was to evaluate the effect of five different metal framework designs on the fracture resistance of the metal-ceramic restorations. MATERIALS AND METHODS. For the purpose of this study, the central incisor tooth was prepared, and the metal analogue of it and a master die were fabricated. The counter die with the 0.5 mm clearance was used for fabricating the wax patterns for the metal copings. The metal copings with five different metal framework designs were designed from Group 1 to 5. Group 1 with the metal collar, Group 2, 3, 4 and 5 with 0 mm, 0.5 mm, 1 mm and 1.5 mm cervical metal reduction respectively were fabricated. Total of fifty metal ceramic crown samples were fabricated. The fracture resistance was evaluated with the Universal Testing Machine (Instron model No 1011, UK). The basic data was subjected to statistical analysis by ANOVA and Student's t-test. RESULTS. Results revealed that the fracture resistance ranged from 651.2 to 993.6 N/$m^2$. Group 1 showed the maximum and Group 5 showed the least value. CONCLUSION. The maximum load required to fracture the test specimens even in the groups without the metal collar was found to be exceeding the occlusal forces. Therefore, the metal frameworks with 0.5 mm and 1 mm short of the finish line are recommended for anterior metal ceramic restoration having adequate fracture resistance.

• 한국지반신소재학회논문집
• /
• 제8권2호
• /
• pp.55-62
• /
• 2009

최근 국토의 균형 있는 발전을 위하여 서해안 및 남해안 지역에 주로 분포되고 있는 연약지반에 대한 건설공사가 활발히 이루어지고 있다. 이러한 연약지반은 지반의 강도가 약하고, 압축성이 강해서 구조물을 축조하기 전에 반드시 표층안정처리, 압밀촉진, 치환공법 등의 지반개량이 선행되어야 한다. 이러한 연약지반 개량공법 중 표층처리공법은 샌드매트의 포설을 이용한 처리가 주를 이루었다. 그러나, 샌드매트공법에 요구되는 모래의 양이 증가함에 따라 공급이 원활하게 이루어지고 있지 않은 상태이다. 본 연구에서는 이러한 문제점을 해결하고자 샌드매트 대체제로서 풍쇄 슬래그의 사용이 적합한지를 판단하기 위하여 기본 물성시험, 실내 통수능 시험, 침하특성 분석을 통해서 확인하고자 한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.223-230
• /
• 2001

The Monkman-Grant (M-G) and its modified parameters were estimated for modified type 316LN and $9{\sim}12Cr-1Mo$ steels with chemical variations. Several sets of creep data were obtained by constant-load creep tests in $550-650^{\circ}C$ ranges. The relation parameters, m, $m^*$, C and $C^*$ were proposed and discussed for two alloy systems. In creep fracture mode, type 316LN steel showed domination of the intergranular fracture caused by growth and coalescence of cavities. On the other hand, the Cr-Mo steel showed transgranular fracture of the ductile type caused from softening at high temperature. In spite of the basic differences in creep fracture modes as well as creep properties, the M-G and its modified relations demonstrated linearity within the $2{\sigma}$ standard deviation. The value of the m parameter of the M-G relation was 0.90 in the 316LN steel and 0.84 in the Cr-Mo steel. The value of the $m^*$ parameter of the modified relation was 0.94 in the 316LN steel and 0.89 in Cr-Mo steel. The modified relation was superior to the M-G relation because the $m^*$ slopes almost overlapped regardless of creep testing conditions and chemical variations to the two alloy systems.