• Advances in materials Research
• /
• v.2 no.2
• /
• pp.99-109
• /
• 2013

In the present investigation, nanocomposite films with poly(methyl methacrylate) (PMMA) as a polymer matrix and barium titanate as a filler were prepared by solution casting method. Barium titanate nano particles were prepared using Ti(IV) triethanolaminato isopropoxide and hydrated barium hydroxide as precursors and tetra methyl ammonium hydroxide (TMAH) as a base. The nanocomposite films were characterized using XRD, FTIR, SEM and dielectric spectroscopy techniques. Dielectric measurements were performed in the frequency range 100 Hz-10 MHz. Dielectric constant of nanocomposites were found to depend on the frequency, the temperature and the filler fraction. Dissipation factors were also influenced by the frequency and the temperature but not much influenced by the filler fractions. The 10 wt% of BT-PMMA nanocomposite had the lowest dielectric constant of 3.58 and dielectric loss tangent of 0.024 at 1MHz and $25^{\circ}C$. The dielectric mixing model of Modified Lichtenecker showed the close fit to the experimental data.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.33.1-33
• /
• 2002

• Journal of the Korean Ceramic Society
• /
• v.26 no.5
• /
• pp.617-624
• /
• 1989

Piezoelectric composites of O-3 connectivity were prepared by thermosetting barium titanate-phenolic resin composite under various cruing pressure. Among three kinds of pore in O-3 type ceramic-polymer composite, such as matrix pores, particle pores, and ceramic-polymer interface pores, the effect of interface porosity on the dielectric and piezoelectric constant was investigated. In pure barium titanate ceramics, the porosity factor of dielectric and piezoelectric constants were 5.7 and 5.0, respectively. However, in BaTiO3-polymer composite, the interface porosity factor of the piezoelectric constant was greater than that of the dielectric constant, interface porosity factor b in d33 was 9.8 and in r 4.6. On the other, piezoelectric voltage constant g33 was independent of the porosity of barium titanate ceramics. But in composite system, the piezoelectric voltage constant g33 was decreased with interface porosity.

• 전기의세계
• /
• v.26 no.1
• /
• pp.82-86
• /
• 1977

Semiconducting Barium Titanate shows resistivity anomaly near the transition temperature 120.deg. C. Its transition temperature decreases about 6-7.deg. C per 1 mole % SnO$_{2}$, which is likely to compose (BaSb) (TiSn) $O_{3}$ structure by making Sn$^{+4}$ ions occupy Ti$^{+4}$ ion sites. Grain boundories, whose existance is the cause of having high resistivity in Semiconducting BaTiO$_{3}$ disappear due to the spontaneous polarization below the transition temperature, and it is believed that the phase transition makes semiconducting BaTiO$_{3}$ have resistivity anomaly at certain temperature. Temperature and frequency dependencies of resistivity are also investigated for practical application.ion.

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.642-648
• /
• 2002

Barium Titanate(BaTiO$_3$) nanoparticles were prepared at 22$0^{\circ}C$ through glycothermal process by using barium hydroxide and amorphous titanium hydrous gel as precursor and 1,4-butanediol and distilled water as solvent. It is demonstrated that the size of BaTiO$_3$ particles can be controlled by reaction conditions such as various content of 1,4-butanediol/distilled water volume ratio. This processing method can fabricate BaTiO$_3$ powders, which have a narrow distribution and exhibit good dispersion. The particle size of BaTiO$_3$ powders obtained by glycothermal process were about 50 nm to 200 nm on the condition that reaction temperature was 22$0^{\circ}C$ and holding time was 24 h.

• Journal of the Korean Chemical Society
• /
• v.7 no.4
• /
• pp.254-256
• /
• 1963

A spectrochemical analysis was made to compare the major impurities in $BaTiO_3$ single crystals grown from $KF-BaTiO_3$ system and $TiO_2-BaTiO_3$ system respectively. The present technique was also extended, without any modifications, to the analysis of $SrTiO_3$ crystal.

• Journal of the Korean Ceramic Society
• /
• v.24 no.4
• /
• pp.392-396
• /
• 1987

Pure barium titanate was sintered at $1340^{\circ}C$ for 2, 4, 8, 16 hr to control their grain size. The measurements of breakdown strength and partial discharge characteristics were performed under rising AC voltage(60Hz). With increase of sintering time, the average grain size was increased and breakdown strength was slightly decreased. Partial discharge in pores was observed under high voltage, and a model of dielectric break down in barium titanate ceramics is proposed.

• Journal of the Korean Ceramic Society
• /
• v.22 no.4
• /
• pp.15-20
• /
• 1985

$(Ba_{0.5} Pb_{0.5})_{1-x} Nd_x TiO_3$ 중의 $_x(Nd$의 양)를 변화시키면서 격자상수와 전기전도도를 측정하였다 c축과 a축의 비(c/a) 의 극대값은 실온에 있어서 전기전도도의 극대값과 일치하였다. 이것은 Nd원자의 치환위치와 강유 전성의 변화에 의한 것으로 고찰되었다 Curie 온도이하에서는 Nd 첨가량의 증가에 따라 전기전도도의 활성화에너지가 증가하는 경향을 나타내었다 이것은 입경의 감소에 따른 Spontaneous polarization의 저하가 원인으로 고찰되었다 첨가량의 역학을 입계의 potential barrier의 높이와 관련지어 논하였다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.4 no.1
• /
• pp.27-39
• /
• 1967

The fabrication of the barium titanate ceramic capcitors has been studied. The effects of the impurities for alumina and silica upon mechanical and electrical characteristics have been examined in detail. The preparation of equimolar titanium oxide and barium carbide in addition two percent of alumina and point two five perdcent of silica has shown the best results. This is fired up to thirteen hundred degrees Celsius with the rate of two hundred degrees Celsius per hour and soaked three hous at this temperature. The dielectric constant of this sample is approximately equal with the standard and theoretical values at room temperature. The insulation resitances of the most fabricated capacitors are in the order of twenty thousand megohms, the dielectric constant and the dissipation factor are almost flat up to just below of curie temperature, and the porosities of the most ceramics are less than point one percent and well close or equal to zero percent.

• Analytical Science and Technology
• /
• v.11 no.4
• /
• pp.260-265
• /
• 1998

Spherical, ${\mu}m$-sized particles of barium titanyl oxalate were prepared by thermal decomposition of dimethyl oxalate in acidic barium and titanium solutions. Precipitation was carried out in the presence of several supporting anions. Spherical particles having a specific type of particle size distribution. i.e., unimodal or bimodal distribution, with mean size in the range of $0.2{\sim}3{\mu}m$, were formed depending on the supporting anions, oxalate ion generation rate and aging time. Particles of barium titanyl oxalate settled on the bottom of the beaker at the aging time of 120 min grew to the critical monosize of about $1.5{\sim}3{\mu}m$. XRD spectra and chemical analyses of barium titanate showed that barium titanyl oxalate with high qualities could be synthesized by choosing chloride ion as a supporting anion and increasing the reaction temperatures.