• 한국진공학회지
• /
• 제15권3호
• /
• pp.287-293
• /
• 2006

R.F. PACVD법을 이용하여, 벤젠을 반응기체로 사용하여 순수한 DLC필름을 증착하였다. DLC필름의 마찰마모특성은 시험 환경을 제어하기 위하여 챔버로 고립된 ball-on-disk형식의 마모시험기를 이용하여 측정하였다. 상대습도에 따른 필름의 마찰특성을 관찰하기 위하여, 상압에서 챔버 내의 습도를 0-90%로 조절하면서 관찰하였다. 그리고 상대면 물질의 영향을 알아보기 위하여 스틸볼과 함께 DLC필름이 코팅된 스틸볼을 사용하였다. 스틸볼을 사용시 습도가 0%에서 90%로 증가함에 따라 마찰계수가 0.025에서 0.2로 크게 증가하였다. Ferich debris가 생성되지 않는 DLC가 코팅된 볼을 사용하여 실험한 경우에, 마찰계수는 상대 습도가 90%인 경우에도 0.08정도로, 스틸볼을 사용하였을 경우보다 훨씬 더 낮은 습도의존성을 보여주었다. 스틸볼 사용시 나타나는 DLC필름의 마찰계수의 큰 습도의존성은 습도가 증가함에 따라 debris의 크기 증가와 함께 스틸볼의 마모로 인한 Fe-rich debris의 생성과 밀접한 관계가 있음을 확인 할 수 있었다. 그리고 스틸볼을 사용하여 90%의 습도에서 마모시험을 하는 중간에 습도를 0%로 변화시키며 관찰한 결과, 마찰계수 값이 급격히 감소하였다. 이와 같은 결과를 통하여, Fe-rich debris가 마찰계수에 미치는 영향은 debris내의 Fe원소가 습도에 매우 민감한 흑연상의 전이층을 형성시킨다는 것을 확인 할 수 있었다.

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.260-266
• /
• 2002

DLC films were deposited on Si wafer by RF plasma assisted CVD using CH4 gas. Tribological tests were conducted using rotating type ball on disk friction tester in dry air. Four kinds of mating balls were used. The mating balls were made with stainless steel but apply different annealing conditions to achieve different hardness conditions. Testing results in all load conditions showed that the harder the mating materials, the lower the friction coefficient among the three kind of martensite mating balls. In case of austenite balls, the friction coefficients were lower than fully annealed martensite ball. The high friction coefficient in soft martensite balls seems to be caused by the larger contact area between DLC film and ball. The wear tracks of DLC films and mating balls could have proven that effect. Measuring the wear track of both DLC films and mating balls have similar tendency comparing to the results of friction coefficients. Wear rate of austenite balls were also smaller than that of fully annealed martensite ball. The results of effect of applying load showed, the friction coefficients were become decrease when the applying loads exceed critical load conditions. The wear track of mating balls showed that some material transfer occurs from DLC film to mating ball during the high friction process. Raman spectra analysis showed that transferred material was a kind of graphite and contact surface of DLC film seems to undergo phase transition from carbon to graphite during the high friction process.

• 전자공학회논문지
• /
• 제53권1호
• /
• pp.22-26
• /
• 2016

본 논문에서는 공 모양의 구조를 이용하여 공진형 무선 전력 전송용 송 수신기를 설계 및 구현하였다. 제안된 송신기의 코일을 공 모양으로 감음으로써 3차원의 공간으로 자계 에너지를 방사하도록 하였다. 송신기의 각각의 면을 나선 구조로 함으로써 높은 Q 값을 얻을 수 있도록 설계하였다. 이것은 기존의 무선 전력 전송 시스템에서 위치에 따라서 전송효율이 변하는 문제점을 해결하였다. 그리고 3차원에서의 공진형 무선 전력 전송을 가능하게 한다. 이때의 공진주파수는 6.78 MHz이며, 송 수신기 사이 거리가 200 mm일 때, 3차원 전 방향에서 40% 이상의 전송 효율을 얻을 수 있었다.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.145-152
• /
• 2001

Thermal deformation of a machine tool structure can be evaluated from the analysis of the whole temperature field. However, it is extremely inefficient and impossible to know the whole temperature field by measuring temperatures at every point. So, the temperature estimator is required, which can predict the whole temperature field from the temperatures of just a few points. In this paper, a 1-dimensional heat transfer problem is modeled with modal analysis and state space equations. And then the state observer is designed to estimate the intensity of heat source and the whole temperature field in real time. The reliability of the estimator is verified by making comparison between solutions obtained from the proposed method and the exact solutions of examples. The proposed method is applied to the estimation of temperature distribution in a ball screw system.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.735-739
• /
• 2013

The error motion of a machine tool spindle directly affects the surface errors of machined parts. Spindle motion errors such as three translational motions and two rotational motions are undesirable. These are usually due to the imperfectness of bearings, stiffness of spindle, assembly errors, and external force or unbalance of rotors. The error motions of the spindle need to be reduced for achieving the desired performance. Therefore, the level of error motion needs to be estimated during the design and assembly process of the spindle. In this study, an estimation method for five degree-of-freedom (5 DOF) error motions for a spindle with an angular contact ball bearing is suggested. To estimate the error motions of the spindle, the waviness of the inner-race of bearings and an external force model were used as input data. The estimation model considers the geometric relationship and force equilibrium of the five DOFs. To calculate the error motions of the spindle, not only the imperfections of the shaft and bearings but also driving elements such as belt pulley and direct driving motor systems are considered.

• 한국정밀공학회지
• /
• 제18권4호
• /
• pp.151-159
• /
• 2001

As huge energy transfer systems like a nuclear power plant, steam power plant and petrochemical plant are operated for a long time, mechanical properties are changed by degradation. The life time of the systems can be affected by the mechanical properties. BI(Ball Indentation) test has a potential to replace conventional fracture tests like a uniaxial tensile test, fracture toughness test, hardness test and so on. In this paper, we would like to present the ageing evaluation technique by the BI method. The four classes of the thermally aged 1Cr-!mo-0.25V specimens were prepared using an artificially accelerated aging method. Tensile tests, fracture toughness tests, hardness tests and BI tests were performed. The results of the BI tests were in good agreement with fracture characteristics by a standard fracture test method within 5%. The IDE(Indentation Deformation Energy) of a BI technique as a new parameter for evaluating a degradation was suggested and the new IDE parameter clearly depicts the degradation degree.

• 한국정밀공학회지
• /
• 제13권10호
• /
• pp.139-145
• /
• 1996

The machining accuracy and performance is largely influenced by the static, dynamic and thermal characteristics of spindle systems in machine tools, because the spindle system is a intermedium for cutting force from tool and machine powef from motor. Large cutting force and power are transmitted by bearing with a point or line contact. So, the spindle system is the static and dynamic weakest point in machine structure. For improvement of static stiffness of spindle system can be changed design parameters, such as diameter of spindle, stiffness of bearing and bearing span. But for dynamic stiffness, the change of the design parameters are not useful. In this paper, the combined bearing arrangement is suggested for high damping spindle system. The combined bearing arrangement is composed of tandem double back to back arrangement type ball bearins and a high damping hydrostatic bearing. The variation of static deflection and amplitude in first natural frequency is evaluated with the location of hydrostatic bearing between front and rear ball bearing. The optimized location of hydrostatic bearing for high static and dynamic stiffness is determined rapidly and exactly using the mode shape and transfer function of spindle. The calculation of damping effect on vibration by unbalance of grinding wheel and pulley in optimized spindle system is carried out to verify the validity of the combined bearing arrangement. Finally, the simulation of grinding process show that the surface roughness of workpiece with high damping spindle system is 60% better than with ball bearing spindle system.

• 한국안전학회지
• /
• 제15권1호
• /
• pp.28-35
• /
• 2000

As huge energy transfer systems like a nuclear power plant, steam power plant and petrochemical plant are operated for a long time, mechanical properties are changed by degradation. The life time of the systems can be affected by the mechanical properties. So determination of the integrity of the metallic structure is required either to en4sure that failure will not occur during the service life of the components or to evaluate the lifetime extension of the structure. An automated ball indentation(ABI) method was developed as a non-destructive technique for evaluating the integrity of such metallic components. In this paper, we would like to present the aging evaluation technique by the ABI method. The five classes of the thermally aged CF8M specimens were prepared using an artificially accelerated aging method. After holding 100, 300, 900, 1800 and 3600 hours at 43$0^{\circ}C$, the specimens were cooled down using water to room temperature respectively. The tensile test, hardness test, charpy impact test, ABI test were performed. The results of the fracture test were compared with those of ABI test and the new evaluation technique of the integrity of metallic structures was developed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.171-176
• /
• 2000

As huge energy transfer systems like a nuclear power plant, steam power plant and petrochemical plant are operated for a long time, mechanical properties are changed by degradation. The life time of the systems can be affected by the mechanical properties. BI(Ball Indentation) test has a potential to replace conventional fracture tests like a uniaxial tensile test, fracture toughness test, hardness test and so on. In this paper, we would like to present the aging evaluation technique by the BI method. The four classes of the thermally aged 1Cr-1Mo-0.25V specimens were prepared using an artificially accelerated aging method. Tensile tests, fracture toughness tests, hardness tests and BI tests were performed. The results of the BI tests were in good agreement with fracture characteristics by a standard fracture test method. The IDE(Indentation Deformation Energy) of a BI technique as a new parameter for evaluating a degradation was suggested and the new IDE parameter clearly depicts the degradation degree.

• 한국운동역학회지
• /
• 제17권1호
• /
• pp.191-199
• /
• 2007

This study was conducted to examine the biomechanical characteristics of open spike in the volleyball to improve the technique of the volleyball spike. The subjects were six male college and high school athletes. The motions of volleyball spike were filmed by using two Sony VX 2000 Video Cameras. The mechanical factors were angle and angular velocity of body segments in the upper and the lower limbs. The conclusions were as follows; 1. The angle of the shoulder joint of the skilled showed larger than that of the unskilled in impacting of the volley ball spike. 2. The angle of the elbow joint of the skilled showed larger than that of the unskilled in impacting of the volley ball spike. 3. The angle of the wrist joint of the skilled showed smaller than that of the unskilled in impacting of the volley ball spike. 4. The angle of the hip joint of skilled showed larger than that of unskilled in impacting of the volley ball spike. 5. The angle of the knee joint of the skilled and the unskilled showed same in take off and impacting of the volley ball spike, and that of the skilled showed smaller than that of the unskilled in take-off touchdown and touchdown after impact of the volley ball spike. 6. The angle of the ankle joint of skilled showed larger than unskilled in take-off of the volley ball spike. 7. The angular velocity of the shoulder joint, elbow joint, wrist joint of the skilled showed faster than that of the unskilled in impacting of the volley ball spike. Taken together the result of them, I have come to conclusion that knee joint angle in touchdown of the take off should be decreased and knee joint angle in take off should be increased, and then stability of the take off should be made and, and that extension of the elbow joint should be made and wrist joint angle decreased and shoulder and hip joint angle increased, and then C.O.G of the arm and hand should be positioned ahead C.O.G of the body in impacting for effective impact of the spike, and that the transfer of the angular velocity of body segments for effective impact of the spike make from the proximal segment to the distal segment at spike in volleyball.