• Journal of Technologic Dentistry
• /
• v.30 no.2
• /
• pp.39-45
• /
• 2008

Titanium and its alloys are widely used as dental implants materials because of their excellent mechanical properties. However, the alumina and zirconia ceramics are preferred to use as the substitute of Ti implants because there is a problems in esthetics and biocompatibility in Ti implant. The the glass infiltrated alumina ceramics are studied to increase the toughness and biocompatibility. The 45S5 and soda-lime glass powder was mixed with ethanol at ratio of 1:1 and brushed on the surface of alumina. Then it was heat treated in the electric furnace at $1400^{\circ}C$ from 30 min. to 5 hours. The glass powder was controlled from 200 to $350{\mu}m$ using ball milling. After heat treatment, the glass infiltrated specimen was tested in universal testing machine to measure the bending strength. The surface microstructure of each specimen was observed with SEM. The biocompatibility of 45S5 and soda-lime glass coated alumina was investigated using PBS at $36.5^{\circ}C$ incubator. The specimen was immersed in PBS for 3, 5, 7, 10 days. After that, the surface morphology was investigated with SEM. As the results of experiment, the 45S5 bioglass infiltrated alumina show the increase of bending strength according to the increasing of heat treatment time from 30 min. to 5 hours at $1400^{\circ}C$ Finally the 1370N bending strength of alumina increased to 1958N at 5 hours heat treatment, which shows 1.4 times higher. In contrast to this, the soda lime glass infiltrated alumina ceramics shows the convex curve according to heat treatment time. Thus it shows maximum bending strength of 1820N at 1 hour heat treatment of $1400^{\circ}C$ It gives 1.3 times higher. However, the bending strength of soda lime glass infiltrated alumina is decreasing with increasing heat treatment time after 1 hour. The precipitation on the surface of 45S5 glass infiltrated alumina was revealed as a sodium phosphate ($Na_{6}P_{6}O_{24}6H_{2}O$) and the amount of precipitation is increasing with increasing of immersion time in PBS. In contrast to this, there is no precipitation are observed on the surface of soda lime glass infiltrated alumina. This implies that 45S5 glass infiltrated alumina brings more biocompatible when it is implanted in human body.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.10
• /
• pp.687-698
• /
• 2001

This paper presents a three dimensional stacked pad area away (PAA) package configuration as an implementation method of radio frequency (RF) circuits. 224MHz RF circuits of intelligence traffic system(ITS) were constructed with the stacked PAA RF pakage configuration. In the process of manufacturing the stacked PAA RF pakage, RF circuits were partitioned to subareas following their function and operating frequency. Each area of circuits separated to each subunits. The operating characteristics of RF PAA package module and the electrical properties of each subunits were examined. The measurement of electrical parameters for solder balls which were interconnects for stacked PAA RF packages showed that the parasitic capacitance and inductance were 30fF and 120pH, respectively, which might be negligible in PAA RF packaging system. HP 4396B network/spectrum analyzer revealed that the amplification gain of a receiver and transmitter at 224 MHz was 22dB and 27dB, respectively. The gain was 3dB lower than designed values. The difference was probably generated from fabrication process of the circuits by employing commercial standard

• The Korean Journal of Emergency Medical Services
• /
• v.9 no.2
• /
• pp.147-168
• /
• 2005

It examined the doubt point which AED motive relates until now, the AED should have bought a life how, present address of our country site pre-hospital care, comparison it tried to observe the advanced nation instance back. Gist of this research the AED important cold region once compared to informed to how many cardiac arrest patient, against him the what kind of preparation wanted informing the necessary cold region. It soaks simultaneously but the AED motive is widely supplied distant in future and it is generality and it is feeble but it wanted doing one morning. The habit difference of an American who does of course meat diet mainly and a Korean is many and it compares in the United States and the cardiac arrest patient comparison occurs holds a point few. To become Western anger but and be caused by with thin dietary life, stanching bleeding cung, with the fact that the heart attack is increasing rapidly with the hyperextension. It is a talk which anyone it knows all. The major league most Choi huy Sub in condition will catch the ball which floats and the multi co-player and to collide when falling down, the medical device which is committed with emergency aid is AED motive. From the United States subway station and the shopping which are a public place on the baseball field outside the jar which it will drive, the museum and the school, easily there is it will be able to discover the AED from the court of justice back. The Pittsburg university the students per the individual $30 the core phyey were receiving the smallness lifestyle alcoholic beverage and a AED motive actual training with mercy of degree. From the United States distant in future the AED motive is sold even from the retail store and. From our country like this plan government offices temporary disposal education from from 119 fire fighters emergency structure company in fire fighting government employee and nursing must magnify a former enterprise rainy spell in summer multi temporary disposal education with the head which it will burn with the head. This plan in early rising will be able to become fixed in Korea it forecasts with the fact that. The research which it sees it leads and like the United States to some day become fixed even from our country to believe and suspicion it is not and in the people in approach ease one AED supply plan fire fighting government employees stand in the first and feed with the fact that must be positive at this enterprise they become.

• 대한공업교육학회지
• /
• v.38 no.2
• /
• pp.1-26
• /
• 2013

This study inquired following research questions by a narrative research method : What was the job of an engineer in mechanical design field? How did he fulfill his job-related learning in his workplace? What were the context and the characteristic of the job-related learning in the workplace? And some implications of the job-related learning on engineering education were discussed. We identified that the research participant's career as a mechanical engineer has developed through three stages. At first, he engaged on conceptual design of a semi-conductor test machine through self-initiated learning from basic to whole system of the machine. At second stage, he leaded a design group for the concrete design of a ball type semi-conductor test machine. In this stage he learned the meaning of cooperation and cooperative learning. At third stage, he initiated to found an entrepreneur company that was specified to design a semi-conductor test machine. He became CEO of the company. He learned the R & D policy making through contacts with global company, visiting exhibition in abroad. Eventually his main task as a mechanical engineer was the problem solving in the process of machine design. He had experienced and learned through his works : project management, independent fulfilling of tasks, functional analysis and reverse engineering, conceptualizing and test, cohesive cooperation, dialogue and discussion, mediation of conflict, human relationship, leadership. The implication of the narrative analysis on engineering education is, proposed, to give the students more chances to experience and to learn such activities.

• Asian-Australasian Journal of Animal Sciences
• /
• v.26 no.4
• /
• pp.564-572
• /
• 2013

Two trials were conducted to investigate the effect of decreasing the crude protein (CP) content of diets for finishing pigs containing two levels of available lysine on nutrient digestibility, nitrogen (N) balance and production performance. Ten finishing diets containing five levels of CP (on average 144, 155, 168, 182 and 193 g/kg fresh basis) and two levels of available lysine (6.9 and 8.2 g/kg fresh basis) were formulated. The diets were offered to pigs on a performance trial (n = 800 Large White (LW)${\times}$Landrace (LR) pigs) from 10 wk of age until finish at 21 wks+5 d of age. Average daily gain (ADG), average daily feed intake (ADFI) and feed conversion ratio (FCR) were calculated. In addition, a digestibility/N balance trial was conducted using pigs (n = 80 $LW{\times}LR$) housed in metabolism crates. Digestibility of dry matter (DM), CP, oil, fibre and energy was determined. N balance values were determined through analysis of N content of urine and faeces ('as determined'). N balance values were also calculated using ADG values and assuming that 16% of growth is protein deposition ("as calculated"). Pig performance was poor between 10 and 13 wk of age which indicated that the dietary treatments were nutritionally inadequate for pigs less than 40 kg. There was a significant (p<0.01) quadratic effect of increasing CP level on feed intake, ADG and FCR from 10 to 13 wk which indicated that the lower CP levels did not supply adequate levels of essential or non-essential amino acids. There was no effect of increasing available lysine level throughout the early period, which in conjunction with the response in older pigs, suggested that both 8.2 and 6.9 g/kg available lysine were insufficient to drive optimum growth. There was a positive response (p<0.05) to increasing available lysine level from 13 wk to finish which indicated that 6.9 g/kg available lysine was not adequate for finishing pigs. Energy digestibility decreased with decreasing CP level of diets containing 6.9 g/kg available lysine which may be attributed to the higher fibre content of the lower CP diets. Nitrogen excretion (g/d) was lowered when dietary CP was reduced regardless of whether the values were determined through balance or calculated using ADG. Calculated N excretion decreased linearly (p<0.001) and quadratically (p<0.001) with decreasing dietary CP content. When the N balance figures calculated in this study were compared with those quoted in the Northern Ireland and English Nitrates Directive Action Programmes, N excretion was less per pig (wean to finish) offered a 169 g/kg CP, 8.2 g/kg available lysine diet (2.39 kg vs 3.41 kg (Northern Ireland) and 2.93 kg (England)).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.8
• /
• pp.847-853
• /
• 2011

In this study, a hybrid powder-extrusion process involving the control of temperature dwelling time for improving the formability of Zn-22Al powder was developed and the effect of dwelling time on the mechanical properties of a spur gear with a pitch circle having a diameter of 1.8 mm was investigated. General extrusion experiments were carried out at different temperatures such as 290, 300, and $310^{\circ}C$. Spur gears with good qualities and without any surface defects were obtained in the case of extrusion temperature of $310^{\circ}C$ and ball-milling duration of 32 h. The Vickers hardness distribution was non-uniform, and after the sintering process, an internal crack was generated because of the different deformation energy between gear central part and teeth. To overcome the abovementioned problems, research on controlling the dwelling time of the extrusion temperature in the powder-extrusion process was carried out. Good-quality spur gears were obtained when the dwelling time was 15 min.

• Journal of Korean Ophthalmic Optics Society
• /
• v.8 no.1
• /
• pp.35-39
• /
• 2003

The display technology on the retina is the key role in inspecting the condition of the patients. 2-dimensional retina image is widely used in the eye examination as of today. Recently, 3-dimensional retina image ones have been introduced to this area, but the quality of the image is not fully satisfied to the operator. For the purpose of developing 3-D retina imaging instrument, the optimization of a 3-D retina imaging system using Code-V tool was investigated in this thesis. He-Ne laser having the wavelength 632.8 nm was used to make a power source to detect the retina. Several lenses and mirrors installed on sledge which were developed to perform focus control on 3-D device were designed to make a beam focusing and direct line. Polygon scanner having 24 mirror facets and galvanometer making tilting movement were utilized to make a 2-D laser plane. Also, design of eye ball had been fulfilled to see the focus of the 2-D plane. Reflected ray from retina detected on the sensor array with the same path. All cognitive components were optimized for aberration correction in order to focus on retina. Results of optimization were compared to those of initial designed optics system. On the basis of above results, the result of third aberration has been corrected to stable values to the optical system. MTF evaluating the resolution of an image has been closely correlated to the diffraction limit and PSF indicating the strength distribution of an image has shown the SR value as 0.9998 having high performance. The possibility of new and powerful 3-D retina image instrument was verified by simulating each component of the instrument by Code-V.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.5
• /
• pp.1229-1238
• /
• 2020

The purpose of this study is to clarify the psychological importance of golf player's clothing selection by phenomenological analysis. The study subjects were male and female golf players who participated in the golf tour from October 2017 to March 2018, and a total of 4 male players and 2 female players were selected using the snow ball sampling method. For data analysis, we first coded what we got through in-depth interviews and observations of participation to be organized and analyzed first. Second, classification was conducted based on major themes or phenomena, and meaningful interpretation and research were conducted. In addition, to increase the truth and validity of this study, the true value, applicability, consistency and neutrality of the qualitative research process proposed by Guba & Lincoln (1981). The results of the analysis are as follows. Golf-wear for me, Jinx, My golf wear are my face. Conclusion, Through this study, you can understand the psychological implications of the golf-wear chosen by the golf player and expect positive effects to provide golf player's feedback in the course of making the golf-wear.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.206-211
• /
• 2020

Tungsten alloys are used widely in general industrial fields, but they are difficult to cast, so products are manufactured using powder metallurgy. In this study, a mixed powder of tungsten, nickel, and iron homogenized using a ball mill was added to pure water as a solvent, and PVA as a binder was added to prepare a spray drying mixture. The mixed liquid was prepared using a spraying machine. A study was carried out to produce a granular powder that can reduce the variations between products during the molding and sintering process of the powder metallurgy method. A preliminary experiment was conducted to confirm the influence of the variables in the granulation process. Through the preliminary test results, this experiment was performed with the volume of solvent of the spray drying the mixture as an independent variable, and granular powder having a mean particle size similar to that of the existing mass-production conditions and an increased apparent density was prepared. In addition, a pilot test was conducted for the molding and sintering process. The improved granular powder reduced the characteristic variation (weight variation) of the mass-produced product.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.4
• /
• pp.659-666
• /
• 2006

Servo-motors are used as key components of automated system by performing precise motion control as accurate positioning and accurate speed regulation in response to the commands from computers and sensors. Especially, the linear brushless servo-motors have numerous advantages over the rotary servo motors which have connection with the friction induced transfer mechanism such as ball screws, timing belts, rack/pinion. This paper proposes an estimation method of unknown motor system parameters using the informations from the sinusoidal driving type linear brushless DC motor dynamics and outputs. The estimated parameters can be used to tune the controller gain and a disturbance observer. In order to meet this purpose high performance Digital Signal Processor, TMS320F240, designed originally for implementation of a Field Oriented Control(FOC) technology is adopted as a controller of the liner BLDC servo motor. Having A/D converters, PWM generators, rich I/O port internally, this servo motor application specific DSP play an important role in servo motor controller. This linear BLDC servo motor system also contains IPM(Intelligent Power Module) driver and hail sensor type current sensor module, photocoupler module for isolation of gate signals and fault signals.