• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.19-20
• /
• 2000

We have developed the 12.1" SVGA reflective type color TFT-LCD(Thin Film Transistor - Liquid Crystal Display) with the high aperture ratio and well designed reflector for the applications such as mini note PC, Note PC and electronic book. The panel shows the high reflectance(30%) and contrast ratio(20:1) resulted from optimizing the optical films and designing the embossing shaped reflector. By improving the chromacity, the color reproducibility was increased up to 20%. As removing the backlight unit, we reduced the power consumption, thickness and weight of the panel to 0.8W, 2.2mm, and 250gram, respectively. According to the above performances, we have obtained fabrication process for mass production, and furthermore, could have access to fast market launching.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.6
• /
• pp.530-534
• /
• 2008

The LGP with nanometer structures resulted in enhancement of optical efficiency. Its fundamental mechanism is to recycle the polarized light via one round-trip through QWP(Quarter-wave Plate) but the maximum efficiency to reach with this method is limited up to 2. To get the larger efficiency than this a LGP with 1D PC(one-dimensional photonic crystal) nanometer-patterned on its top and bottom surfaces is suggested. For its optimum design the computer simulation is performed and suggests a grating that the spatial frequency between adjacent patterns is 500nm, its height 250nm, duty cycle 50%, and its cross section is rectangular. The angles of transmitted light are nearly the same as the results expected from the generalized Snell's law. Thus the Mathematica code, developed in this experiment, will be applied to designing the optimized LGP. The LGP with nanometer-patterened 1D PC LGP on its both surfaces shows the enhancement of transmitted intensity distribution up to 5.7 times.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.687-690
• /
• 2009

It has been recently reported that nano-sized MgO single crystal powders emit ultraviolet by stimulation of electrons under vacuum condition. Therefore, in this study, nano-crystalline MgO powders were applied to a xenon plasma flat fluorescent lamp for LCD backlight to improve emission efficiency of the lamp by help of extra ultraviolet from nano-MgO. For comparison with nano-crystalline MgO powders, MgO nano-thin film was applied directly on phosphors inside a lamp panel through e-beam evaporation The luminance and efficiency of FFL with an addition of MgO nano-crystal powders on phosphors were improved by around 20%. Application of MgO thin film to phosphors worsened the emission characteristics of FFLs, even rather than FFL without MgO. The reason came from insufficient stimulation of phosphors by UV, crystallinity of MgO, and low secondary electron coefficient.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.231-234
• /
• 2009

In order to realize the high luminance and luminous efficacy MFFLs for LCD backlights, we optimized the phosphor profile to enlarge the surface area. The MFFL with the new phosphor profile shows a very wide luminance range from 2,600 to 17,000 nit with the corresponding luminous efficacy from 66 to 32.5 lm/W. The results were obtained with the color coordinate of the phosphor to be around (0.25, 0.23). And the single cell is expanded into a multi-structured configuration to realize a 32 inch-sized lamp by a simple repetition of the single cells, and a new driving scheme is proposed for an adaptive local dimming and scanning drive using dual auxiliary electrodes and bipolar drive scheme. Especially the ultra high luminance and luminous efficacy results suggest the duty time of illumination of the backlight unit can be significantly reduced.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.906-910
• /
• 2005

In this paper, comparing and analyzing the distribution of High brightness as domestic lamps and Japanese products go thinner and lighter, we setting an effective composition. standard. By comparing and analyzing the feature, brightness, chromaticity and uniformity of domestic LGPs and Japanese products, early home-manufacturing and stabilization in home-manufacturing are possible. By comparing and analyzing the distribution of brightness as sariheets are ved, we can design an ideal sheet composition.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1665-1666
• /
• 2006

TFT-LCD(Thin Film Transistor Liquid Crystal Display)는 표시장치로서 실용화된 후 많은 상품에 적용중이다. 그러나, LCD는 자체 발광능력이 없으므로 그후면에서 LCD 화면을 밝혀주는 BLU(Backlight Unit)를 필요로 한다. BLU는 내부 광원으로 밝기가 균일한 평면광을 만들어 LCD 화면을 균일하게 면조사하는 역할을 한다. LCD가 적용되는 분야중 Note PC에는 광원으로 CCFL(Cold Cathode Fluorescent Lamp)가 적용되어 왔지만, 최근 고휘도, 박형화, 저소비 전력을 달성하기 위해 CCFL로는 한계가 있어 LED(Light Emitting Diode)를 적용한 BLU를 제작하기 위한 연구가 진행되고 있다. 본 연구에서는 점광원인 LED 적용한 LED에 있어서 요구되는 휘도 균일성을 향상시키기 위해서는 LED광원이 적용된 BLU의 외관 품질 향상을 위한 도광판 입광부 구조 최적화를 광추적 Simulation을 통해 예측하고 향상시킬 수 있는 구조를 제안한다. Simulation결과, 외관품질 개선을 위해 도광판 입광면에 130도의 Serration과 휘도를 향상하기 위해 도광판 밑면에 렌즈 형상의 바 구조를 도출해 적용한 결과 외관품질향상과 휘도향상을 얻었다.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.271-278
• /
• 2011

This paper presents a LLC resonant controller IC for secondary side control without external active devices to achieve low profile and low cost LED back light units. A gate driving transformer is adopted to isolate the primary side and the secondary side instead of an opto-coupler. A new integrated dimming circuitry is proposed to improve the dynamic current control characteristic and the current density of a LED for the brightness modulation of a large screen LCD. A dual-slope clock generator is proposed to overcome the frequency error due to the under shoot in conventional approaches. This chip is fabricated using 0.35 ${\mu}m$ BCD technology and the die size is $2{\times}2\;mm^2$. The frequency range of the clock generator is from 50 kHz to 500 kHz and the range of the dead time is from 50 ns to 2.2 ${\mu}s$. The efficiency of the LED driving circuit is 97 % and the current consumption is 40 mA for a 100 kHz operation frequency from a 15 V supply voltage.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.416-417
• /
• 2007

MmSH injection molding method to fabricate light guiding plate with nano-sized pattern was developed. A stamper was fabricated through photolithography, dry etching, and electroplating processes. While the stamper with nano-sized pattern in mold was kept at $180^{\circ}C$ during injection process, that was cooled down to $90^{\circ}C$ quickly after the injection process. The nano-sized pattern on light guiding plate processed by MmSH injection molding method was well transferred from stamper compared to that processed by conventional injection molding process.

• Korean Journal of Optics and Photonics
• /
• v.21 no.2
• /
• pp.53-60
• /
• 2010

An integrated light guide plate (LGP) was designed for liquid crystal displays (LCD) without using prism and diffuser sheets. The integrated LGP is textured with micro-patterns on both the top and bottom surfaces. The textures effectively substitute for a single prism-sheet and a diffuser sheet in LCD displays without decreasing the brightness and uniformity. A LCD display with our integrated light guide is simulated to give average luminance of 4560 cd/$m^2$, luminance uniformity of 83% horizontal viewing angle $60^{\circ}$ and vertical viewing angle $56^{\circ}$. Therefore an ultra thin (slim) back light unit can be constructed with fewer optical sheets, which reduces the manufacturing cost and so improves price competitiveness.

• Korean Journal of Optics and Photonics
• /
• v.16 no.2
• /
• pp.113-120
• /
• 2005

Luminous efficiency and uniformity in a LCD-BLU are mainly determined by fine scattering patterns formed on the light guide panel. We propose a novel fabrication method of 3-dimensional scattered patterns based on anisotropic etching of silicon wafers. Micro-pyramid patterns with 70.5 degree apex-angle and micro-prism patterns with 109.4 degree apex-angle can be self-constructed by the wet, anisotropic etching of (100) and (110) silicon wafers, respectively, and those patterns are easily duplicated by the PDMS replica process. Experimental results on spatial and angular distributions of irradiation from the light guide panel with the micro-pyramid patterns were very consistent with the calculation results. Surface roughness of the silicon-based micro-patterns is free from any artificial defects since the micro-patterns are inherently formed with silicon crystal surfaces. Therefore, we expect that the silicon based micro-patterning process makes it possible to fabricate perfect 3-dimensional micro-structures with crystal surface and apex angles, which may guarantee mass-reproduction of the light guide panels in LCD-BLU.