• Bulletin of the Korean Chemical Society
• /
• 제24권9호
• /
• pp.1333-1338
• /
• 2003

Hollow Fiber flow field-flow fractionation (HF-FlFFF) has been tested in polyacrylonitrile (PAN) membrane channel in order to compare it with polysulfone (PSf) membrane channel. It has been experimentally shown that the separation time of 0.05-0.304 ${mu}m$ polystyrene latex (PSL) standards in PAN membrane channel is shorter than that in PSf channel by approximately 65%. The optimized separation condition in PAN membrane is ${\dot V}_{out}/{\dot V}_{rad}=1.4/0.12\;mL/min$, which is equal to the condition in PSf membrane channel. In addition both the resolution ($R_s$) and plate height (H) in PAN membrane channel are better than that in PSf membrane channel. The membrane radius was obtained by back calculation with retention time. It shows that the PSf membrane is expanded by swelling and pressure, but the PAN membrane doesn't expand by swelling and pressure.

• 한국정보통신학회논문지
• /
• 제8권6호
• /
• pp.1135-1141
• /
• 2004

본 논문은 신경회로망의 학습 알고리즘과 패턴인식을 위한 신경회로망 모델을 논의하였고, 생산가공 시스템에서의 광량 센서에 대한 물체 검출, 신경회로망을 이용한 패턴 분류, 마이크로 컨트롤러 시스템 그리고 DC 서보 모터의 제어기 설계에 대하여 논의하였다. 본 논문은 제시된 시스템의 구조를 기반으로 생선의 아가미와 꼬리 부분을 절단하는 어류 가공 시스템에 적용하여 실험하였고, 산업현장에 응용할 수 있는 지능제어시스템의 성능을 그 결과로 제시하였다.

• 한국항해항만학회지
• /
• 제33권2호
• /
• pp.119-125
• /
• 2009

The effect of plastic board drains (PBDs)on ground improvement was checked out considering three crucial factors: ground settlement, undrained shear strength, and residual water head. First, the settlement analysis including initial settlement induced by reclamation of sand mat was conducted by back calculation analysis with measured data. Its result showed toot the PBDs used for this site worked well on improving soft ground. Secondly, the undrained shear strength was investigated by laboratory and in-situ tests including unconsolidated-undrained triaxial compression (UU) tests, unconfined compression tests, in-situ vane tests, and cone penetration tests. From the test results, they showed that the undrained shear strength of the improved ground by PBDs was significantly increased as well as the strength increasing ratio especially $10{\sim}15m$ below the ground surface on site. Thirdly, the residual water head measurement from the in situ dissipation test was found the same as the static water head, which indicated primary consolidation was completed and the effect of soil improvement with PBDs can be confirmed.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.800-811
• /
• 2018

This paper presents a regenerative braking control scheme for Switched Reluctance Machine (SRM) drive in Electric Vehicles (EVs). The main purpose is to maximize the recovered energy during battery charging by taking into account the nonlinear physical characteristics of the Switched Reluctance Machine. The proposed regenerative braking method employs the back-EMF in the generation process as a complicated position-dependent voltage source. The proposed maximum power recovery (MPR) operation of the regenerative braking is first based on the maximization of the extracted power from the machine and then the maximization of the power transferred to the battery. The maximum power extraction (MPE) from SRM is based on maximizing the energy conversion ratio by the calculation of the optimum PWM switching duty cycle, turn-on, and turn-off angles. By using the impedance matching theorem that allows the maximum power transfer (MPT) of the MPE, the proposed MPR is achieved. The parametric averaged value modeling of the machine phase currents in the chopping control mode is used for MPR realization. By following this model, a nonlinear equivalent input resistance is derived for the battery internal resistance matching. The effectiveness of the proposed regenerative braking method is demonstrated through simulation results and experimental implementation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.8-10
• /
• 2005

In a general purpose inverter, a dead-time compensation strategy is very important for reducing torque ripples and acoustic noises of motors. However, in the case of small capacity inverter, the accurate dead-time compensation is hard to be obtained because a removal of the switching noise in a feedback current signal is difficult on condition of low-cost implementation. In this paper, the operation characteristics of the general purpose inverter applied the dead time compensation algorithm using an instantaneous back calculation of the phase angle of the current are presented.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 춘계학술대회 논문집
• /
• pp.40-45
• /
• 2001

Recently, the use of numerical simulation has been increased rapidly because of the development of high performance computer systems. The present study is aimed to investigate flow characteristics of a two-dimensional sharp plane. Unsteady calculation by FDM(Finite Difference Method) based upon SOLA scheme which was performed at $Re=2{\times}10^4$in viscous incompressible flow within a finite domain on the irregular grid formation. Total numbers of irregular grids are $8{\times}10^4$. The minimum grid size is 1/100 of the plane length L which is the representative length. The inclined angles of every objects are $15^{\circ}, \;30^{\circ}\;and\; 45^{\circ}.$ And, the edge angle of the plane is $30^{\circ}.$ This study discussed the flow characteristics in term of the turbulent intensity, vorticity and frequency analysis. Developed flows show that the periodic Karman vortices occur at the back of the plane.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2017년도 추계학술발표회
• /
• pp.69-69
• /
• 2017

Flame arrestor as end of line flame arrester for endurance burning prevents a light-back at deflagration and stabilized burning (during and after endurance burning) of potentially explosive vapor-air and gas-air mixtures at the end of vent pipes. In a flame arrestor, spring is an important part. The spring load as well as the spring's elasticity determine when the hood is opened. In addition, the spring have to work in high temperature condition due to gas burning. Therefore, it is necessary to analyze mechanical load and elasticity of spring when gas is burned. Based on the dynamic calculation on working process of a specific flame arrestor, analysis of spring is taken. A three dimensional model for spring burned in flame arrestor by using CFD simulation. Results of the CFD analysis are input in FEM simulation to analyze structure of the spring. The simulation results can predict and estimate the spring's load and elasticity at variation of the spring's deflection. Moreover, the obtained result can provide makers with references to optimize design of spring as well as flame arrestor.

• 한국전기전자재료학회논문지
• /
• 제29권1호
• /
• pp.62-67
• /
• 2016

In this paper, the IES file was measured by applying a secondary optical lens to a 21 W LED engine, and the lighting calculation software RELUX was used to perform simulations with the data file of this measurement. For two-lane (two way) concrete paved roads, six LED engine are applied to each streetlight and simulation results show that Uo (uniformity) 0.56, UI (longitudinal uniformity) 0.86 and TI (threshold iIncrement) 9% which satisfies the required standards. RELUX was also used to LED streetlights by designing them in three dimensions, that is ${\pm}25%$ of the arm length of 2.8 m standardized by the road lighting standards of the Korea Expressway Corporation. Comparative analysis was carried out on adjustments were made in increments of 0.1 m that Uo, UI, and TI values in the range of arm lengths from 2.1 m~3.5 m. For the arm length range of 2.1 m~2.4 m, Uo was high, whereas UI was low. Therefore, we present the optimal light distribution values designed for an arm length of 2.5 m.

• 한국가스학회지
• /
• 제3권1호
• /
• pp.1-7
• /
• 1999

알루미늄합금(5083-0)의 표면균열시험편의 관통전후의 피로거동을 조사하였다. 관통전의 피로균열형상은 거의 반타원형이며, 측정된 형상비는 Newman-Raju식의 K를 이용하여 계산한 값보다 더 크다. 관통후의 뒷면에서의 피로균열성장거동은 거의 유사하였으며 3영역으로 나누어졌다. 표면균열길이가 긴 경우, 피로균열전파법칙을 사용함으로서 표면균열재의 판두께 관통후의 피로균열 전파특성을 정량적으로 평가될 수 있음을 알 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 D
• /
• pp.2286-2288
• /
• 2001

In this paper, a drive system of induction motor with high performance is realized on the viewpoint of the design and experiment, using the DSP (TMS320F240). The speed controller for induction motor drive system is designed on the basis of a neuro-fuzzy network. The neuro-fuzzy controller acts as a feed-forward controller that provides the right control input for the plant and accomplishes error back-propagation algorithm through the network. The proposed network is used to achieve the high speedy calculation of the space vector PWM (Pulse Width Modulation) and to build the neuro-fuzzy control algorithm, for the real-time control. The proposed neuro-fuzzy algorithm on the basis of DSP shows that experimental results have good performance for the precise speed control of an induction motor drive system. It is confirmed that the proposed controller could provide more improved control performance than conventional v/f vector controllers through the experiment.