• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.300-304
• /
• 1993

Chip formation control is an important problem in the automation of manufacturing process, since the continuous chip can cause catastrophic failures of the tooling and entangle the workpiece causing damage. However, it is impossible to predict chip form correctly due to the complex nature of cutting process. In order to detect the chip form for unmanned manufacturing, a new identification method is proposed. The feasibility of using acoustic emission signals from the sensing plate for identification of chip form is investigated. Experiments were conducted under the various cutting conditions. When the acoustic emission sensor is attached to the sensing plate, it turns out that the moving averaged AE signals correlated well with the collision of segmented chips with the plate. The sensitivity of moving averaged AE signals to chip congestions due to continuous chip formation is illustrated as well.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.534-537
• /
• 1995

An open loop vibrational control of underactuated mechanical system with amplitude and frequency modulations is investigated. The underactuated systems sonsidered in the paper are assumed to have free joints with no brake. The active joints are positioned first by a linearizing control, and then periodic oscillatory input are applied to them to move the remaining free joints to their desired states. A systematic way of obtaining averaged systems for the underactuated systems with oscillatory vibration is developed. A complete solution to the open loop control strateegy in terms of determining amplitudes and frequencies for general system is still under investigation. However, a specific control design for 2R manipulator which is obtained through the averaged system is demonstrated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.428-433
• /
• 2002

There have been many studies to visualize the vibration and noise of rotary compressor. Most of these studies assumed that the signal is stationary and the time-averaged signal is used for visualization. However, the noise and vibration signals generated during one cycle of crank shaft vary continuously. In this paper, the noise and vibration of rotary compressor which vary continuously are visualized by short time fourier transform method. The location of source and the transfer path of vibration and noise at arbitrary frequencies, which can not be visualized by averaged signal, can be visualized clearly.

• 한국자기공명학회논문지
• /
• 제6권1호
• /
• pp.12-19
• /
• 2002

A shift-averaged Haar wavelet transform was introduced as a new and excellent tool to distinguish real peaks from the noise contaminated NMR signals. It is based on Haar wavelet transform and translation-invariant denoising process. Donoho＇s universal threshold was newly introduced to the shift-averaged Haar wavelet transform for the purpose of automated noise suppression, and was quantitatively compared with the conventional uniform threshold method in terms or threshold and signal to noise ratio (SNR). New algorithm was combined with a routine to suppress a large solvent peak by singular value decomposition (SVD). Combined algorithm was applied to the real spectrum that containing large solvent peak.

• ETRI Journal
• /
• 제27권2호
• /
• pp.227-230
• /
• 2005

A specific anthropomorphic mannequin (SAM) model was used to investigate the relation between local specific absorption rate (SAR) and head size. The model was scaled to 80 to 100% sized models at intervals of 5%. We assumed that the shell of the SAM model has the same properties as the head-equivalent tissue. Five handsets with a monopole antenna operating at 835 MHz were placed in the approximate cheek position against the scaled SAM models. The handsets had different antenna lengths, antenna positions, body sizes, and external materials. SAR distributions in the scaled SAM models were computed using the finite-difference time-domain method. We found that a larger head causes a distinct increase in the spatial peak 1-voxel SAR, while head size did not significantly change the peak 1-g averaged-SAR and 10-g averaged-SAR values for the same power level delivered to the antenna.

• 한국소음진동공학회논문집
• /
• 제18권8호
• /
• pp.841-848
• /
• 2008

Based on the averaged Korean head shapes that are the results of digital Korean project by KISTI and Catholic university, experimental apparatus of head dummies of Korean male and female are developed in order to measure head-related transfer functions(HRTF) by using a reverse engineering and rapid prototyping techniques. For the Korean dummies, HRTFs are measured using the substitution method ever 12kHz frequency bands. At every azimuth angle $15^{\circ}$ HRTFs are measured for elevation angles $-30^{\circ}$, $0^{\circ}$ and $-30^{\circ}$. The measured HRTFs are compared with those of KEMAR(knowles electronic manikin for acoustic research) dummy head, which shows $3{\sim}5\;dB$ difference over $4{\sim}5\;kHz$ kHz frequency band.

• 한국유체기계학회 논문집
• /
• 제19권5호
• /
• pp.12-19
• /
• 2016

In present study, a parametric study of a centrifugal compressor with inlet treatment has been performed numerically using three-dimensional Reynolds-averaged Navier-Stokes equations. The shear stress transport turbulence model was used for analysis of turbulence. The finite volume method and unstructured grid system were used for the numerical solution. Tested parameters were related to the geometry of the inlet duct. It was found that the application of circumferentially distributed holes in the inlet duct improves operational stability of the compressor compared to that with conventional inlet duct.

• 한국유체기계학회 논문집
• /
• 제14권5호
• /
• pp.55-62
• /
• 2011

Shape optimization of a Printed circuit heat exchanger (PCHE) has been performed by using three-dimensional Reynolds-Averaged Navier-Stokes (3-D RANS) analysis and surrogate modeling techniques. The objective function is defined as a linear combination of effectiveness of the PCHE term and pressure drop in the cold channels of the PCHE. The cold channel angle and the ellipse aspect ratio of the cold channel are used as design variables for the optimization. Design points are selected through Latin-hypercube sampling. The optimal point is determined through surrogate-based optimization method which uses 3-D RANS analyses at design points. The results of three types of surrogate model are compared each other. The results of the optimizations indicate improved performance in friction loss but low performance in effectiveness than the reference shape.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.187-194
• /
• 2010

Shape optimization of an upper plenum of PBMR type gas cooled nuclear reactor has been performed by using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) analysis and surrogate modeling technique. The objective function is defined as a linear combination of uniformity of flow distribution in the core and pressure drop in the upper plenum and the core. The ratio of thickness of slot to diameter of rising channels, ratio of height of upper plenum to diameter of rising channels, and ratio of eight of the slot at inlet to outlet, are used as design variables for optimization. Design points are selected through Latin-hypercube sampling. The optimal point is determined through surrogate-based optimization method which uses 3-D RANS analyses at design points. The results show that the optimum shape represent remarkably improved performance in flow uniformity and friction loss than the reference shape.

• 한국전산유체공학회지
• /
• 제15권3호
• /
• pp.16-23
• /
• 2010

Shape optimization of an upper plenum of a PBMR type gas cooled nuclear reactor has been performed by using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) analysis and surrogate modeling technique. The objective function is defined as a linear combination of uniformity of flow distribution in the core and pressure drop in the upper plenum and the core. The ratio of thickness of slot to diameter of rising channels, ratio of height of upper plenum to diameter of rising channels, and ratio of height of the slot at inlet to outlet, are used as design variables for optimization. Design points are selected through Latin-hypercube sampling. The optimal point is determined through surrogate-based optimization method which uses 3-D RANS analyses at design points. The results show that the optimum shape represent remarkably improved performance in flow uniformity and friction loss than the reference shape.