• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.138-138
• /
• 2008

In this study, effect of thickness on structural, electrical and optical properties of B doped ZnO:Al (AZOB) films was investigated. AZOB films were deposited on PC substrates by DC magnetron sputtering. The thickness range of films were from 300 nm to 800 nm to identified as increasing thickness, stress between substrate and AZOB film. The. average transmittance of the films was over 80 % until 500 nm. Then a resistivity of $1.58\times10^{-3}\Omega$-cm was obtained. We presented that a AZOB film of 500 nm was optimization to obtain a high transmittance and conductivity.

• Journal of Korean Society on Water Environment
• /
• v.34 no.3
• /
• pp.301-307
• /
• 2018

This study investigated the effects of sediment removal on water quality and phytoplankton development by setting up mesocosms at Uiam Lake, South Korea, and analyzing the environmental parameters and phytoplankton communities between June and October 2015. The comparison between testbed without sediment removal (TB-1) and testbed after sediment removal (TB-2) gave similar values for water temperature, pH, dissolved oxygen (DO), and electrical conductivity. Nevertheless, the average electrical conductivities of the two testbeds were $139{\mu}S/cm$ and $135{\mu}S/cm$, which were lower than the value obtained from the external control point (TB-con; $154{\mu}S/cm$). The small difference in total phosphorus (TP) and total nitrogen (TN) concentrations between the two testbeds implied that sediment removal did not greatly reduce nutrients; however, the phytoplankton cell count had decreased by approximately 37 % in TB-2 (average 1,663 cells/mL) compared to TB-1 (average 2,625 cells/mL). Compared to TB-con, the phosphorus and nitrogen concentrations of the two testbeds had decreased by 39 % and 30 %, respectively, whereas the phytoplankton abundance had decreased by up to 73 %, perhaps because of the blocked inflow of nutrients and the stabilized body of water caused by the installation of the mesocosm. The concentration of geosmin was lower in testbeds than in the external point, because installation of the structures had reduced the cyanobacteria biomass.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.145-150
• /
• 1998

The electrical and mechanical properties of the 8 mol% yittria-stabilized zirconia and alumina composites have been examined as a function of the alumina content. The 3-point bending strength and fracture toughness of the composites increased with increasing alumina content up to 20 wt%. The average grain size of the composites decreased with increasing alumina content up to 20 wt%. The composite with 5 wt% $Al_2O_3$ showed a 3-point bending strength of 310 MPa and fracture toughness about $7.8MPa\cdot\textrm m^{1/2}$. The electrical conductivity of the composites at $1000^{\circ}C$ increased slightly with increasing alumina content up to 10 wt% and decreased monotonically with alumina content. The conductivity of the TZ-8YS with 5 wt% alumina was 0.4 S/cm at $1000^{\circ}C$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.2
• /
• pp.98-107
• /
• 2004

Modified Ni/YSZ cermets for high temperature electrolysis were synthesized by dry or wet mechanical alloying methods. The Ni/YSZ composit particle was directly fabricated from the ball milling of Ni and YSZ powder or obtained from the reduction of NiO/YSZ particle after the ball milling of NiO and YSZ. In the case of the NiO/YSZ composite particle, the dry milling increased the average particle size whereas the wet milling decreased the size. The dry milling showed that fine YSZ particles were distributed over large Ni surfaces while Ni and YSZ particles similar in size were well mixed in the wet milling method. These features were the same in the Ni/YSZ composite particle prepared from Ni and YSZ powders. The electrical conductivity of the wet-milled Ni/YSZ cermet showed the highest value of $2{\times}10^2S/cm$ among the specimens and this value was increased to $1.4\times10^4S/cm$ after the sintering at $900^\circ{C}$ for 1 h.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1075-1080
• /
• 2015

A hybrid electric vehicle (HEV) powertrain has more than one energy source including a high-voltage electric battery. However, for a high voltage electric battery, the average current is relatively low for a given power level. Introduced to increase the voltage of a HEV battery, a compact, high-efficiency boost converter, sometimes called a step-up converter, is a dc-dc converter with an output voltage greater than its input voltage. The inductor occupies more than 30% of the total converter volume making it difficult to get high power density. The inductor should have the characteristics of good thermal stability, low weight, low losses and low EMI. In this paper, Mega Flux^® was selected as the core material among potential core candidates. Different structured inductors with Mega Flux^® were fabricated to compare the performance between the conventional air cooled and proposed potting structure. The proposed inductor has reduced the weight by 75% from 8.8kg to 2.18kg and the power density was increased from 15.6W/cc to 56.4W/cc compared with conventional inductor. To optimize the performance of proposed inductor, the potting materials with various thermal conductivities were investigated. Silicone with alumina was chosen as potting materials due to the high thermo-stable properties. The proposed inductors used potting material with thermal conductivities of 0.7W/m·K, 1.0W/m·K and 1.6W/m·K to analyze the thermal performance. Simulations of the proposed inductor were fulfilled in terms of magnetic flux saturation, leakage flux and temperature rise. The temperature rise and power efficiency were measured with the 40kW boost converter. Experimental results show that the proposed inductor reached the temperature saturation of 107℃ in 20 minutes. On the other hand, the temperature of conventional inductor rose by 138℃ without saturation. And the effect of thermal conductivity was verified as the highest thermal conductivity of potting materials leads to the lowest temperature saturations.

• Korean Chemical Engineering Research
• /
• v.48 no.6
• /
• pp.673-678
• /
• 2010

In the present study, mixed carbon-supported platinum(Pt) nanoparticles were prepared by a chemical reduction method of Pt precursor solution on two types of carbon materials such as activated carbons(ACs) and graphite nanofibers(GNFs). Average crystalline sizes and loading levels of Pt metal particles could be controlled by changing a content of GNFs. The highest electroactivity for methanol oxidation was obtained by preparing the carbon supports having 15 wt% GNFs. Furthermore, with an increase of GNFs content from 0% to 15%, an electrical conductivity was changed from $10^{-4}S/cm$ to $10^{-1}S/cm$. By an introduction of 10 wt% GNFs additive, the electroactivity of platinum particles was enhanced, but was saturated in the case of 15 wt% GNFs contents. This was related with the fact that the electroactivity change was dependent on the electrical conductivity of mixed carbon supports and Pt particle deposition content or deposition morphology.

• Journal of Welding and Joining
• /
• v.26 no.4
• /
• pp.50-54
• /
• 2008

In this research, anode for SOFC has been manufactured from two different kinds of feedstock materials through thermal spraying process and the properties of the coatings were characterized and compared. One kind of feedstock was manufactured from spray drying method which includes nano-components of NiO, YSZ (300 nm) and graphite. And the other is manufactured by blending the micron size NiO coated graphite, YSZ and graphite powders as feedstock materials. Microstructure, mechanical properties and electrical conductivity of the coatings as-sprayed, after oxidation and after hydrogen reduction containing nano composite which is prepared from spray-dried powders were evaluated and compared with the same properties of the coatings prepared from blended powder feedstock. The coatings prepared from the spray dried powders has better properties as they provide larger triple phase boundaries for hydrogen oxidation reaction and is expected to have lower polarization loss for SOFC anode applications than that of the coatings prepared from blended feedstock. A maximum electrical conductivity of 651 S/cm at $800^{\circ}C$ was achieved for the coatings from spray dried powders which much more than that of the average value.

• Korean Journal of Soil Science and Fertilizer
• /
• v.36 no.3
• /
• pp.113-118
• /
• 2003

Rose is one of the major cut-flower crops in Korea. A survey was conducted to investigate the chemical properties of soils cultivating rose under plastic film house at 72 farms in Korea. Soil texture distribution of the samples were loam(43%), silty clay loam(19%), and clay loam(17%). The average chemical properties of the surface soils were pH 5.85, electrical conductivity $3.61dS\;m^{-1}$, organic matter $37g\;kg^{-1}$, nitrate nitrogen $205mg\;kg^{-1}$, phosphorous as Av. $P_2O_5$ $844mg\;kg^{-1}$, and exchangeable potassium $1.41cmol_c\;kg^{-1}$. Available phosphate and exchangeable potassium were accumulated at the level higher than the optimum content in over 70% of the surveyed farms. The flower stalk length was positively correlated with the organic matter content in soil, but was negatively correlated with the electrical conductivity in Red Sandra cultivar.

• Journal of Korean Society of Forest Science
• /
• v.90 no.1
• /
• pp.146-154
• /
• 2001

This research was conducted to investigate the seasonal changes in physicochemical characteristics of stream water at the four points in the northeastern part of the Puk'ansan National Park from July of 1998 to November of 2000. The average pH of stream water was 6.6(6.53~6.74) and the dissolved oxygen was ranged from 11.0 to $11.3mg/{\ell}$, which indicated that the water quality could be categorized in the first class for the quality of river water quality standard. The average electrical conductivity of stream water was 106.8(52.3~154.0) ${\mu}S/cm$ and the electrical conductivities of downstream water were ranged from 139.4 to $154{\mu}S/cm$, which were about 1.7~3.0 times higher than those in upstream water that showed from 52.3 to $81.6{\mu}S/cm$. The amount of anion($Cl^-$, $NO{_3}^-$, $SO{_4}^{2-}$) which indicates the pollution index in downstream was higher than that in upstream, In addition, the seasonal impacts of pollution on stream water were higher in Autumn than in Spring or Summer.

• Korean Journal of Soil Science and Fertilizer
• /
• v.31 no.2
• /
• pp.120-127
• /
• 1998

This study was performed to produce basic data for developing prediction techniques of desalinization through analyzing soil properties of reclaimed tidal lands, using soil samples collected in 11 units of tidal land reclamation projects. The average apparent specific gravity (bulk density), real specific gravity (particle density), porosity, and saturation percentage were measured to be 1.33, 2.64, 49.6%, and 56.3%, respectively. It was estimated that the soil texture class of reclaimed tidal lands would be silt or silt loam. The electrical conductivity and exchangeable sodium percentage were estimated to be $20{\sim}40dS\;m^{-1}$ and 30~50% in the beginning of tidal land reclamation, and the value of pH was measured to be 6.5~7.9. In conclusion, the soil properties of reclaimed tidal lands could be descrived to be saline-sodic soils with the high electrical conductivity and exchangeable sodium percentage.