• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.93-98
• /
• 2004

A reasonable analysis of cutting force in end milling may give much advantage to improvement of productivity and cutting tool life. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. Specific cutting constants of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, feed, axial depth, and radial depth of cut. The effects of the cutting conditions on the specific cutting force constants in milling were studied. The model is verified through comparisons of model predicted cutting forces with measured culling forces obtained from machining experiments

• 동력기계공학회지
• /
• 제2권2호
• /
• pp.73-80
• /
• 1998

The identification of drilling joint dynamics which consists of drilling and structural dynamics and the on-line time series detection of malfunction process is substantial not only for the investigation of the static and dynamic characteristics but also for the analytic realization of diagnostic and control systems in drilling. Therefore, We have discussed on the comparative assessment of two recursive time series modeling algorithms that can represent the drilling operation and detect the abnormal geometric behaviors in precision roundshape machining such as turning, drilling and boring in precision diemaking. For this purpose, simulation and experimental work were performed to show the malfunctional behaviors for drilling operation. For this purpose, a new two recursive approach (Recursive Extended Instrument Variable Method : REIVM, Recursive Least Square Method : RLSM) may be adopted for the on-line system identification and monitoring of a malfunction behavior of drilling process, such as chipping, wear, chatter and hole lobe waviness.

• Tribology and Lubricants
• /
• 제20권4호
• /
• pp.209-217
• /
• 2004

Lubrication characteristics between a cylinder block and a valve plate for high speed bent-axis type hydraulic pump play an important role in volumetric efficiency and durability of pump. In this paper, a finite element method is presented for the computation of the pressure distribution between a cylinder block and a valve plate for high speed bent-axis type hydraulic pump. Also, a Runge-Kutta method is applied to simulate the cylinder block dynamics of three-degrees of freedom motion. From the results of computation, we can draw two major conclusions. One is related to the fluid film characteristics between a cylinder block and a valve plate and the other is related to the average leakage that is determined by the pressure gradient and the clearance near the discharge port. The numerical results of cylinder block dynamics were compared with the experimental results using eddy-current type gap sensors those are fixed at a pump housing.

• 한국정보기술응용학회:학술대회논문집
• /
• 한국정보기술응용학회 2005년도 6th 2005 International Conference on Computers, Communications and System
• /
• pp.305-310
• /
• 2005

Recently, many organizations in various industries have introduced e-businesses for the purpose of adding value to their businesses. However, due to no comparable business models to e-business in the past, there are no reliable yardsticks to predict the performance of an e-business. This paper considers an environmental change analysis as a means to resolve this difficulty. System Dynamics (SD) could be a useful tool to generate effective results by examining the e-business model. SD model is developed to analyze the effects of an e-sales channel which was appended to the existing sales channels in the steel manufacturing industry. The results show an increase in average price and sales volume through the use of an auction process on the e-marketplace. Stocking expenses are reduced as well by the increase of the sales turnover. A possible scenario was adopted to the developed simulation model and investigated strategic issues to draw desirable strategies with market changes.

• Journal of Mechanical Science and Technology
• /
• 제15권6호
• /
• pp.735-742
• /
• 2001

This paper reports on the dynamics and friction characteristics of piston skirt with consideration of mixed lubrication. Piston skirt is an important part of the engine that transforms fuel into mechanical energy. The durability and low friction characteristics are important recent issues in piston skirt design. In this paper, the piston skirt motion is analyzed with consideration of mixed lubrication and piston skirt tilting motion. The entire trajectory of piston motion is obtained by using transient numerical method. Also various parameter studies are performed for piston skirt design and the development of lower frictional engine.

• 한국공작기계학회논문집
• /
• 제13권4호
• /
• pp.9-15
• /
• 2004

A reasonable analysis of cutting force in end milling may give much advantage to improvement of productivity and cutting tool life. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. The specific cutting constants of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, feed, axial depth, and radial depth of cut. The model is verified through comparisons of model predicted cutting forces with measured cutting forces obtained from machining experiments. The results showed good agreement and from that we could predict reasonably the cutting forces in end milling.

• 상하수도학회지
• /
• 제23권5호
• /
• pp.573-581
• /
• 2009

In the case that the average velocity within rectangular-shaped sedimentation basin is less than 1.5cm/sec, and Froude number less than $10^{-6}$, it can not be expected that the longitudinal baffle improves the sedimentation efficiency. Also, since relatively lower velocity increases the effect of geostrophic body force, asymmetric flow pattern on a plane occurs within the basin. From the results of CFD (Computational Fluid Dynamics) simulation, in the case that the highest velocity within rectangular-shaped sedimentation basin is over 1.5cm/sec, and Froude number over $10^{-6}$, it can be expected that the longitudinal baffle installed within rectangular-shaped sedimentation basin improves the sedimentation efficiency.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.1-9
• /
• 2004

For improvement of productivity and cutting tool lift, cutting force in end milling needs to be predicted accurately. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. Specific cutting force coefficients of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, fled, axial depth and radial depth of cut. The effects of the cutting conditions on the specific cutting force constants in milling were studied. The model is verified through comparisons of model predicted cutting forces with measured cutting forces obtained from machining experiments.

• 한국기계가공학회지
• /
• 제2권2호
• /
• pp.60-66
• /
• 2003

For the estimation of chatter lobe boundary it is very important to calculate the natural mode of cutting process. There are many time series algorithms for getting the natural mode of structural endmilling dynamics considering the cutting process. In this study, we have compared several time series methods such as AR algorithm, ARX, ARMAX, ARMA, Box Jenkins, Output Error, Recursive ARX, Recursive ARMAX considering the sampling frequency. As a results, the ARX, ARMAX and IV 4 are more desirable algorithms for the calculation of modal parameters such as natural frequency and damping ratio In endmilling operation. Also these algorithms may be adopted for the natural mode estimation of endmilling operation for chatter lobe prediction.

• 한국진공학회지
• /
• 제4권4호
• /
• pp.367-372
• /
• 1995

We investigate the Au(001) surface reconstruction, numerically, by Molecular Dynamics (MD) simulation. We find that the top-most layer of Au(001) surface is reconstructed to a contracted hexagonal face, and relaxed about 0.05$\AA$ upward at room temperature. The contraction ratio with respect to a unreconstructed Au(111) surface is about 3.5%. The hexagonal layer is slightly distorted and buckled. The surface corrugation is found to be about 0.28$\AA$ on average. In our earlier work we have predicted the in-plane orientation of the reconsturcted layer to be either $0^{\circ}$ or $0.7^{\circ}$ depending on the size of the cluster. However, we find only $0.0^{\circ}$ in this simulation because the size of the cluster correspoding to the $0.7^{\circ}$ orientation is larger than the current limitation of MD simulation. These findings are in good agreement with experimental results.