• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.193-200
• /
• 2002

Simple spring-damper-mass models have been widely used to investigate whole-body vortical biodynamic response characteristics of the seated vehicle driver. Most previous models have not considered the effect of wobbling masses; i.e. heart, lungs, liver, intestine, etc. In this study, 4 -DOF seated driver model including one non-rigid mass representing wobbling visceral mass, 5-DOF model including intestine, and 10-DOF model including five lumbar vertebral masses were proposed. The model parameters were identified by a combinatorial optimization technique. simulated annealing method. The objective function was chosen as the sum of error between model response of seat-to-head transmissibility and driving point mechanical impedance and those of experimental data for subjects seated erect without backrest support. The model response showed a good agreement with the experimental response characteristics. Using a 10-DOF model, calculated resonance frequency of lumbar spine at 4Hz was matched well with experimental results of Panjabi et al.

• 오토저널
• /
• 제13권6호
• /
• pp.82-89
• /
• 1991

In order to investigate the characteristics of flow around the intake around the intake valve exit, discharge coefficient and the velocity near the valve exit in steady state were measured using X-type hot-wire. Valve and valve seat insert used in experiment were constructed as the same shape of production engine and the flow characteristics at various flow rates and valve lifts were investigated. From the results of discharge coefficient measurements, it is observed that there exists a similarity between the flow characteristics around the production engine valve and the typical poppet valve. Measurement of the velocity at the valve exit shows that the normalized radial velocity between the primary direction of flow and the valve angle is large, but the difference becomes smaller as the flow rate increases.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.66-75
• /
• 1997

Sound transmission from the luggage comparment into the car cabin is important in the viewpoint if exhaust and road noises of passenger cars. In this paper, acoustic modal coupling between passenger and luggage compartments through loudspeaker holes at parcel shelf is dealt with for a sedan type passenger car with rigid rear seat. For these purposes, a half-scaled model car is tested and computed by the indirect BEM. Predicted acoustic transfer functions are compared with experimental ones and they agree reasonably well. It is found that the fore-aft resonance frequencies of the passenger cavity in the absence of coupling holes are tend to shift to higher frequencies when the luggage compartment is coupled to the passenger cavity.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.147-158
• /
• 1997

This paper presents the analysis technique and procedure of main engine components-cylinder block, cylinder liners, gasket and cylinder head-using the finite element method, which aims to assess mainly the potential of lower oil consumption in a view point of engine design and to decide subsequently the accuracy of engine design which was done. The F.E. model of an engine section consisting of one whole cylinder and two adjacent half cylinders is used, whereby the crankcase is cut off at the block bottom deck. By means of a 3-dimensional F.E. model-including cylinder block, liners, gasket, cylinder head, bolts and valve seat rings as separate parts a linear analysis of deformations and stresses was performed for three different loading conditions;assembly, thermal and gas loads. For the analysis of thermal boundary conditions also the temperature field had to be evaluated in a subsequent step.

• 한국자동차공학회논문집
• /
• 제8권1호
• /
• pp.101-109
• /
• 2000

Occupant protection in the side impact of a car became one of the most important issues of car crashworthiness due to high injury level in a side impact crash. An accurate simulation of the side impact crash is an essential tool for the reduction of development time and cost for side impact safety system. This paper describes a new test methodology that can accurately generate the crash pulses of a vehicle and a door in a very cost-effective manner, and then evaluates the injury values of the dummy for the various sled pulses. This test methodology is simple and easy to approach because the door velocity is controlled by the hydraulic actuator and brake and the seat velocity is only adjusted by the friction force of the hydraulic brake. The superiority of the proposed test methodology is proven by the evaluation of dummy's injury values according to the change of the pressure of the hydraulic brake and by the application as a tool for the development of side airbag.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.120-128
• /
• 1997

The variations of the temperature field in a passenger compartment were measured by using a HSI true color image processing system and TLC(Thermochromic Liquid Crystal) solution. This temperature measurement technique was proved to be useful for analyzing the ventilation flow. The flow field in the passenger compartment was visualized using a particle streak method with pulsed laser light sheet. The temperature field and flow field in the passenger copartment were affected significantly by the ventilation mode. The panel-vent mode heating had shorter elapse time to reach a uniform temperature than the foot-vent mode under the same ventilation condition and nonuniformity inside the passenger compartment could be minimized effectively by using the bilevel heating mode. The temperature increase rate in the rear passenger compartment was iower than the front compartment, especially in the vicinity of the rear seat occupants' knee level.

• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.29-36
• /
• 2005

In oder to generate various shock signals in a field study, a passenger car was driven at several speeds over road profiles that included a number of half sine shaped bumps of various heights. A triaxial SAE pad sensor was mounted on the front passenger seat to measure the acceleration signals which might produce subjective discomfort. The measured accelerations were correlated with the subjective assessments of 14 subjects. The magnitude of subjective discomfort was found to be proportional to the VDV and also the peak to peak of the frequency weighted acceleration signal.

• 한국자동차공학회논문집
• /
• 제8권3호
• /
• pp.139-150
• /
• 2000

Although a number of neck injuries are generated, the data which quantify the kinematic response of the human head and cervical spine in low-speed rear-end automobile collisions is very limited. On this problem, just few in vitro experimental research or some experimental research using dummy on neck injury by rear-end collision was conducted, thus systematic research is requested on full scale injury mechanism. An occupant model for the response of the occupant subject to rear-end collision using commercial dynamics package DADS was developed. Developed model shows more close agreement with the experimental data compared with the MADYMO simulation results for the cases of ${\delta}V=16$ kph in sled test. For the case of ${\delta}V=8$ kph and 33.5 kph with production seat, model also shows its reliable response compared with experimental results using Hybrid III and Hybird III with RID.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.135-142
• /
• 2004

The severe frontal crash tests are NCAP with belted occupant at 35mph and FMVSS 208 with unbelted occupant at 25mph, This paper describes the design process of occupant protection systems, airbag and seat belt, under the two tests. In this study, NCAP simulations are performed by Monte Carlo search method and cluster analysis. The Monte Carlo search method is a global optimization technique and requires execution of a series of deterministic analyses, The procedure is as follows. 1) Define the region of interest 2) Perform Monte Carlo simulation with uniform distribution 3) Transform output to obtain points grouped around the local minima 4) Perform cluster analysis to obtain groups that are close to each other 5) Define the several feasible design ranges. The several feasible designs are acquired and checked under FMVSS 208 simulation with unbelted occupant at 25mph.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.202-209
• /
• 1998

For development of SDI(Spark-ignited Direct Injection) engine, stratified mixture formation with adequate strength at spark plug was required in wide range of engine operating conditions. So, spray structure under high ambient pressure and spray distribution after impingement on piston bowl in motoring engine was visualized by using laser equipments. Also, incylinder bulk flow structure was measured by using PIV (Paiticle Image Velocimetry) system. Counter-rotating tumble port and bowl piston was found effective to conserve bulk motion directed to spark plug in compression stroke. In addition, mask attached near valve seat in intake port was proposed to attenuate conventional tumble component and enhance counter-rotating tumble component.