• 기술사
• /
• 제32권5호
• /
• pp.118-125
• /
• 1999

Air pollutant emissions from airplane engines are estimated about 2 to 4 % of mobile source of USA and European countries which is not a large portion of current air pollution. But the passengers and airfreights are continuously increasing 5 to 7% annually and potential demands of air transportation services come to present, it could effect air pollutant emissions of USA will increase within 15 years. In case of our country, there has been continuous increase of air transportation service due to considerable economic growth in recent years and increase of air pollutant emissions of major international airports has followed. Rapid increase of air transportation due to launching of Inchon International Airport could effect air pollution dominantly. By this circumstance environmental specialist as well as mass communication raised necessity of air pollutant emission regulation from airplane engines. It is estimated that air pollutant emissions from airplane engines in our country is 2.7% of automobile sources, 10,809 ton, which is the same level as USA and European countries. It is increased by 12,2% compared to air pollutant emissions during 1996 and it will be increased more than a half of current air pollutant emission within 15 years due to our country's economic condition. Therefore implementation of airplane engine emissions regulation as well as test standards and accumulation of technology about characteristics of airplane engine emission and reduction method are needed. And continuous estimation of air pollutant emission from airplane engines and monitoring of increment as well as development of countermeasures by long term are necessary.

• 한국정밀공학회지
• /
• 제33권3호
• /
• pp.207-216
• /
• 2016

A gerotor is suitable for miniature manufacturing because it has high discharge per 1 cycle and a simple structure, while also being widely used for lubrication oil of engines and as a hydraulic source of automatic transmission. In the automobile industry, improvements in fuel efficiency and noise reduction have recently come to the fore. It has also been necessary to continuously improve the flow rate and noise of internal gear pumps for better fuel efficiency through optimal gerotor and port shape design. In this study, to develop an optimal gerotor with a new lobe shape, 2-ellipses-combined, the equation of the lobe shape was derived, and CFD analysis results were compared for 2-ellipses with those of the previous gerotors (3-ellipses and ellipse1-involuteellipse2). A performance test for the oil pump with the optimal rotor (2-ellipses) was carried out and showed good agreement with the results obtained from CFD analysis.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2000년도 창립총회 및 춘계학술발표회
• /
• pp.28-32
• /
• 2000

There are many different chemical pollutants that originate from atmospheric deposition and transportational activities along roads. This paper review the characteristics of heavy metal pollution, relationships between land use and pollutant load in urban area. Four land use areas in Seoul were selected for sampling and study with different characteristics during the period from April 1998 and February 2000. A series of studies have been carried out concerning the physicochemical characteristics of the sediments settling down in a gully pot to evaluate the contamination for heavy metals. The sediment samples from gully pots were characterized by the chemical extraction experiments. Sediments are characterized by very high concentrations of heavy metals, probably because of a long-term accumulation of vehicle- and industrial-related pollutants. The characteristics of heavy metal pollution show that each land use has different sources of contaminations. Mean Zn concentration in Yeouido and Junggu areas is 2-3 times higher than those in Dobonggu area. This suggests that Zn may be derived from the source of automobile traffic. The mean concentrations of Cu and Cr are very significantly high in Junggu and Gurogu areas and indicate that the industrial activities may contribute to the accumulation of Cu and Cr in sediments. The low Pb levels throughout the whole study areas in Seoul can be accounted for the use of unleaded gasoline since 1987.

• 한국자동차공학회논문집
• /
• 제20권4호
• /
• pp.76-81
• /
• 2012

In recent, there are tremendous efforts to apply co-generation concept in automobile to improve its thermal efficiency. The co-generation is basically a simple Rankine Cycle that uses the waste heat from the engine exhaust and coolant for heat source. In spite of developed nano technology and advance material science, the bulky co-generation system is still a big concern in automotive application. Therefore, the system should be effectively designed not to add much weight on the vehicle, but the capacity of the waste heat recovery should be still large. With such a goal in mind, the system thermal efficiency was investigated in terms of the system operation condition and working fluid. This paper provides a direction for the optimal design of the automotive co-generation system.

• 한국수소및신에너지학회논문집
• /
• 제26권1호
• /
• pp.64-70
• /
• 2015

Organic Rankine cycle (ORC) is an useful cycle for power generation system with low temperature heat sources ($80{\sim}400^{\circ}C$). Since the boiling point of operating fluid is low, the system is used to recover the low temperature heat source of waste heat energy. In this study, a ORC with R134a is applied to recover the waste energy of condenser of coal fired power plant. A system model is developed via Thermolib$^{(R)}$ under Simulink/MATLAB environment. The model is composed of a refrigerant heat exchanger for heat recovery from coal fired condenser, a drum, turbine, heat exchanger for ORC heat rejection, storage tank, water recirculation pump and water drip pump. System analysis parameters were heat recovery capacity, type of refrigerants, and types of turbines. The simulation model is used to analyze the heat recovery capacity of ORC power system. As a result, increasing the overall heat transfer coefficient to become the largest of turbine power is the most economical.

• Journal of Life Science
• /
• 제9권2호
• /
• pp.76-81
• /
• 1999

216 microorganisms which able to degrade wasted lubricant were isolated in the region of contaminated with wated lubricant such automobile repair shops, garages and gas stations in Taejon. Most activated strain among them is selected and used in this research. The microorganism in identified as Acinetobacter lwoffii 16C-1, which shows active growth and hydrocargon utilization withnormal alkane such as tetradecane, hexadecane and octadecane, and do not grow aromatic hydrocargons, cycloalkane, and branched alkane. In addition, A. lwoffii 16C-1 has resistance to heavy metals such as Ba, Li, Cr, and Mn more than 6.4mg/ml, and showed negligible tolerance against antibiotics. Effects of environmental conditions including concentration of wasted lubricnt, pH, NaCl concentration, nitrogen source and phosphate on microorganism growth and emulsification were studied. 2% of wasted lubricant, pH 7.0, 0-1% of NaCl, 0.2% of peptone, and 0.01% of K2HPO4 is turn out to be optimum condition. By the analysis of remaining oils, almost of hydrocarbons added to the media are removed by A. lwoffii 16C-1 at 30$^{\circ}C$ after 2 days of culture, which showed excellent oil degradation characteristics.

• 한국정밀공학회지
• /
• 제33권11호
• /
• pp.927-935
• /
• 2016

A gerotor is suitable for miniature manufacturing because it has a high discharge per cycle and a simple structure, while also being widely used as lubrication oil of engines and the hydraulic source of automatic transmission. In the automobile industry, it has been necessary to continuously improve the flow rate and noise of internal gear pumps for better fuel efficiency through optimal gerotor design. In this study, to obtain an optimal gerotor with an ellipse-elliptical involute-ellipse combined lobe shape, an automatic program was developed for calculating performance parameters and drawing a gerotor profile. An oil pump was assembled with the optimal gerotor together with the port used at the actual field and CFD analysis was performed on this assembly using Ansys-CFX. A performance test for the oil pump was carried out and showed good agreement with the results obtained from the theoretical analysis and the CFD analysis.

• 열처리공학회지
• /
• 제23권5호
• /
• pp.257-262
• /
• 2010

Recently, metal molding has become essential not only for automobile parts, but also mass production, and has greatly influenced production costs as well as the quality of products. Its surface has been treated by carburizing, nitriding and induction hardening, but these existing treatments cause considerable deformation and increase the expense of postprocessing after treatment; furthermore, these treatments cannot be easily applied to parts that requiring the hardening of only a certain section. This is because the treatment cannot heat the material homogeneously, nor can it heat all of it. Laser surface treatment was developed to overcome these disadvantages, and, when the laser beam is irradiated on the surface and laser speed is appropriate, the laser focal position is rapidly heated and the thermal energy of surface penetrates the material after irradiation, finally imbuing it with a new mechanical characteristic by the process of self-quenching. This research estimates the material characteristic after efficient and functional surface treatment using HPDL, which is more efficient than the existing CW Nd:YAG laser heat source.

• 한국산업융합학회 논문집
• /
• 제10권1호
• /
• pp.21-26
• /
• 2007

As DDI or GDI engine discharges very low heat due to its high thermal efficiency, the heat source is not enough for heating the passenger compartment in cold climate condition. To remedy the heating problem, the conventional HFC-134a automotive air-conditioning system has been attempted to run as a heat pump mode. Futhermore, an auxiliary electric heater of new type was equipped to the heat pump air-conditioning loop as a new approach. Hence, a proto-type heat pump air conditioner has been made and tested to investigate the feasibility of the HFC-134a automobile air-conditioning system that could be worked as a heat pump. The experiment results showed that the sufficient heating capacity could be obtained by adding a heat pump with an new electric type auxiliary heater into the conventional heat core in low temperature condition.

• 한국대기환경학회지
• /
• 제15권5호
• /
• pp.657-665
• /
• 1999

Particulate matter produced by diesel engines is of concern to cngine manufactures because of its environmental impact. The majority of diesel particles are in the range of smaller than 1 ${\mu}{\textrm}{m}$. Because of their tiny volume, ultrafine diesel particles contribute very little to the total mass concentration which is currently regulated for automobile emissions. Ultrafinc particles are known to have deleterious effects upon human health cspecially because they penetrate deeply human respiratory tract and have negative effects on the health. In this study, the engine exhaust gas was diluted in a dilution tunnel and the particle size distribution was measured using the scanning mobility particel sizer system. Measurements of the number and the mass concentrations of the diesel exhaust were made under different engine ooperating conditions. The dilution sampling system provided a common basis for collection of the exhaust by cooling and diluting the source emission prior to the measurement. The measurement results showed that the particle size distributions of the exhaust from the diesel vehicles equipment with either heavy-duty or lignt-duty diesel engines, were similar in the particle size range of 0.08~0.2${\mu}{\textrm}{m}$.