• IEMEK Journal of Embedded Systems and Applications
• /
• v.6 no.5
• /
• pp.281-286
• /
• 2011

FMCW Radar sensor is commonly used for an automobile collision avoidance system for rider's safe. Systems using FMCW radar, however, would be one of expensive solutions for just simple rear obstacle detection purpose due to its high cost. In this letter, a short range rear obstacle detector using novel 24GHz AM radar sensor is presented. It can be implemented at significantly lower cost than FMCW radar for practical commercialization. The proposed AM radar sensor module is fabricated in a single aluminum housing to reduce the overall size while using single power supply voltage of 12V with 1200mA current for automotive applications. The measured detection range is up to 210cm with 10cm of distance resolution, which is suitable for a parking assistance system for automobiles.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1011-1014
• /
• 1999

An on-board monitoring system for an automobile emission gas has a test chamber remote from the automobile's engine exhaust gas stream: apparatus for supplying the chamber with sampled exhaust gases. A single hydrocarbon sensor exposed to the exhaust gas in the chamber to render a signal responsive to the hydrocarbon. The conductive ions in emission gas was checked by the HC sensor in test chamber. A preferred application includes hydrocarbons in an automotive exhaust gas stream by exposing a transition porous alumina($Al_{2}O_{3}$) ceramic based sensor to the same exhaust gas stream. By combining the electrical signal, a measure of hydrocarbons can be provided.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.2
• /
• pp.46-52
• /
• 2004

Numerous connectors are used in automobiles for transmission of electrical signals across various electro-mechanical components. The connectors must operate with high reliability in order to minimize failures due to signal degradation. In this work, the effects of contamination at the contact interface of connectors used fur automobile crankshaft position sensor on the impedance change were investigated. An experimental set-up was built to simulate the electrical signal transmitted from the sensor to the engine control unit through a connector. Output from the connector was investigated using connectors contaminated with engine block residues and water droplets. It was found that slight contamination of the connectors could lead to significant signal degradation which can lead to engine failure. Also, the effect of water in the connector altered the signal severely. However, the signal gradually regained the original state as the water evaporated from the interface.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.1021-1023
• /
• 2013

Currently, aircraft and automobile simulator for training provides a variety of training by making hypothetical situation on a simulator Installed on the ground Currently. And the instructor maximizes the effectiveness of the training by Monitoring training and instructing the required training. When trainees are boarding the aircraft or automobile. The Instructor in the ground is not able to monitoring aircraft, automobile. The assessment of the training is not easy after the end of the training Therefore, it is difficult to provide high quality of education to the students. In this paper, Simulation software is to develop the following. Collecting GPS and real-time information for aircraft, automobile ${\grave{a}}implementing$ 3D simulation. Implementing Current image of the aircraft or automobile in the screen by 3D Real-time monitoring of training situation at the control center utilizing for training saving 3D video files Analysis, evaluation on training After the end of the training.

• Journal of the Speleological Society of Korea
• /
• no.79
• /
• pp.47-51
• /
• 2007

As time goes by, ultrasonic wave is getting important and new technology, which is adapted to ultrasonic wave is used to industry such as home appliance, automobile, and high-tech industry. Especially, ultrasonic wave is used an alarm device whether there are things at the rear of I. It's do important device in automobile system because it can prevent car-accident from inattention of the driver. Actually, there has already been lots of the alarm device. But it's expensive and so difficult to set the device. So almost driver don't set device at their automobile. We focus on these problems. We want to make cheap md easy setting device. Ultrasonic wave sensor emits Ultrasonic-signal at outgoing part and receive part accept the signal. Sensor analyzes the signal and Distance is displayed on LCD of device. The device makes alarm if distance is near from something of rear. The device makes break-system operate to prevent drivers from crashing if distance is so near. This device is portable. So normal deriver can set it easily.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.74-83
• /
• 2009

Recently, usage of electric and electronic system for car increases rapidly. Consequently power monitoring supplied to the system is essential for management and controlling. Generally, battery status is monitored through measuring and diagnosing the current measurement method utilizing Hall Effect. Therefore, in this paper, we analysed magnetic field to develop the solution of DC current sensor using Hall Effect which is the core of design and development. By analysing the magnetic field by FEM using Maxwell 3D software, the location of the highest output current and stable part in the Hall IC sensor was shown. Also, the optimal core design of DC current sensor using parametric and Simplex method was presented. A car battery charge and discharge process dependant on time effect on the changing of magnetic field was simulated and compared to the result from the experiment result of actual vehicle.

• Journal of the Korea Convergence Society
• /
• v.11 no.11
• /
• pp.47-53
• /
• 2020

There is a need for a system that provides early warning of presence and type of failure of automobile wheel bearings through the application of predictive fault analysis technologies. In this paper, we presented a sensor module mounted on a wheel bearing and a diagnostic system that collects, stores and analyzes vehicle acceleration information and vibration information from the sensor module. The developed sensor module and predictive analysis system was tested and evaluated thorough excitation test equipment and real automotive vehicle to prove the effectiveness.

• Journal of Aerospace System Engineering
• /
• v.11 no.4
• /
• pp.44-47
• /
• 2017

This work dealt with vibration stability analysis of automotive exhaust sensor. In this work, structural design and analysis of exhaust gas sensor of automobile system were performed. Firstly, structural design requirement of automobile exhaust system was investigated. After structural design, the structural analysis of the exhaust measurement sensor system were performed usig the finite element analysis method. It was performed that the vibration and thermal stress analysis at the high temperature condition. After structural test of target structure, structural test results were compared with analysis results. Through the structural analysis, it was confirmed that the designed measurement sensor structure is safety.

• Transactions of Materials Processing
• /
• v.31 no.2
• /
• pp.103-108
• /
• 2022

Systematic quality control based on real time data is required for modern factories. This study introduced a method of predicting punch wear in the trimming process of automobile parts. Based on monitoring data of the mass production process using a bolt-type piezo sensor, it was shown that precursor symptoms of die wear could be predicted from the change in load pattern with respect to production volume. The load pattern that changed according to the wear of the die was verified by numerical analysis.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.3 s.120
• /
• pp.235-240
• /
• 2007

In this work, the operational deflection shape(ODS) of an automobile exhaust system is measured by using a recently-developed magnetic sensor. The magnetic sensor is composed of a solenoid and two pairs of permanent magnets generating an antisymmetric magnetic field in the lateral direction inside the solenoid. Lateral movement of a ferromagnetic pipe inside the magnetic field of the suggested sensor induces an electromotive force in the solenoid corresponding to the lateral velocity of the pipe. Due to the simplicity and non-contact characteristics of the magnetic sensor, dynamic behaviors of the structures operating under high temperature such as an exhaust pipe can be efficiently observed. It is shown that the lateral ODS of an exhaust system can be successfully measured by the suggested sensors.