• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.7-11
• /
• 2010

Various transmission technologies have been developed to satisfy environmental issues recently. Especially, the technology of the proportional control solenoid valve (PCSV) to ensure high level performance by electronic control has been studied. This study builds an analysis process for designing of the PCSV and characteristic predictions.

• Tribology and Lubricants
• /
• v.30 no.6
• /
• pp.337-342
• /
• 2014

The reduction of drag torque is an important research issue in terms of improving transmission efficiency. Drag torque in a wet clutch occurs because of the viscous drag generated by the transmission fluid in a narrow gap (clearance) between the friction plate and a separate plate. The objective of this paper is to observe the effects of the friction plate area and the clearance on the drag torque using finite element simulation. The two-phase flow of air and oil fluid is considered and modeled for the simulation. The simulation analysis reveals that as the rotational speed increases, the drag torque generally increases to a critical point and then decreases sharply at a high speed regime. The clearance between the two plates plays an important role in controlling drag torque peak. An increase in the clearance causes a decrease in shear stress; thus, the drag torque also decreases according to Newton's law of viscosity. An observation of the effect of the area of contact between transmission fluid and friction plate shows that the drag torque increases with the contact area. The flow vectors inside the flow channel present clear evidence that the velocity of the fluid flows is faster with a larger friction plate, that is, in the case of a larger contact area. Therefore, the optimum size of the friction plate should be determined carefully, considering both the clutch performance and drag reduction. It is expected that the results from this study can be very useful as a database for clutch design and to predict the drag torque for the initial design with respect to various clutch parameters.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.10
• /
• pp.996-1002
• /
• 2009

Elimination of squeal noise occurred during brake application is an important task for the improvement of comforts in an industrial forklift. In this paper, a test rig was developed which was possible for testing of brake noise and an experimental measurement on squeal noise was performed. The causes of the brake noise are identified by experimenting how the factors such as automatic transmission fluid and rpm of drive axle affect the squeal. In order to identify the squeal characteristics, the signal analyses for noise are performed by using frequency spectrums. Also, brake test using a forklift was carried out to confirm the reliability of test results by using a test rig comparing with the occurrence of squeal noise. Experimental results showed that the tendencies of occurrence of squeal noise are well agreed at two test methods by using the test rig and forklift.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.1
• /
• pp.57-62
• /
• 2015

The wet brakes used on a forklift often produce noise upon engagement. The elimination or reduction of this squeal noise is an important task for the improvement of the comfort of those operating these machines. In this paper, a test rig was developed for the testing of brake noise, and the squeal noise was measured with this apparatus. Automatic transmission fluid and grooves in the material of the friction-plate pad were found to be the main factors causing squeal noise. In order to identify the characteristics of this type of noise, signal analyses of the noise were conducted using different frequency spectra. The experimental results showed that the viscosity of the automatic transmission fluid and the groove pattern on the friction-plate pad largely affected the reduction of the wet brake squeal noise made by an industrial forklift.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.33-38
• /
• 2010

As for an oil hydraulic vane pump of vehicle hydraulic systems, the highest of planning technique required by the acquisition of optimum profile data which can be available to predict noises and vibrations. Pressure pulsation may result in considerable vibration and noise of pump component as well as cavitation in hydraulic system. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in chamber surrounding a vane have been investigated. It is very important to predict pressure pulsation in vane pump. This paper presents analysis of technique of vane pump for automatic transmission. The predicted result using AMESim model were good agreement with the experimentally obtained results.

• Journal of Drive and Control
• /
• v.19 no.2
• /
• pp.17-26
• /
• 2022

Recently, automatic transmissions caused a good improvement in the shift quality of a forklift. An advanced shift control algorithm, which was based on TCU firmware, was applied with embedded control technology and microcontrollers. In the clutch-to-clutch shifting, one friction element is released and the other friction element is activated. During this process, if the release and application timings are not synchronized, an overrun or tie-up occurs and ultimately leads to a shift shock. The TCU, which measures only the speed of the forklift, inevitably applies the open-loop shift control. In this situation, the speed ratio does not change during the clutch fill. The torque phase occurs until the clutch is disengaged. In this study, an offline shift logic of the learning control was proposed. It induced a synchronous shift when the learning control progressed. During this process, the reference current trajectory of the release clutch was corrected and applied to the next upshift. We considered the results of the overrun/tie-up characteristics of the upshift performed immediately before. The vehicle test proved that the deviation in shift quality, which was caused by the difference in the mechanical characteristics of the clutch, could be improved by the learning control.

• Journal of Drive and Control
• /
• v.13 no.1
• /
• pp.1-9
• /
• 2016

Nowadays automatic transmission equipped vehicles prevail in construction and agricultural equipment due to their convenience in driving and operation. Though domestic vehicle manufacturers install imported electronic controlled transmissions at present, overseas products will be replaced by domestic ones in the near future owing to development efforts over the past 10 years. For passenger cars, there are many kinds of shift control algorithms that enhance the shift quality such as feedback and learning control. However, since shift control technologies for heavy duty vehicles are not highly developed, it is possible to improve the shift quality with an organized control method. A feedback control algorithm for neutral-into-gear shift, which is enabled during the inertia phase for the master clutch slip speed to track the slip speed reference, is proposed based on the power transmission structure of TH100. The performance of the feedback shift control is verified by a vehicle test which is implemented with firmware embedded TCU. As the master clutch engages along the predetermined speed trajectory, it can be concluded that the shift quality can be managed by a shift time control parameter. By extending the proposed feedback algorithm for neutral-into-gear shift to gear change and shuttle shift, it is expected that the quality of the shift can be improved.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.56-61
• /
• 2010

Simulator is a development equipment which enables the ECU to operate in normal mode by simulating the interface signal between ECU and mechanical system electrically. Embedded simulator means simulation function is embedded in ECU firmware, hence the electrical signal interface is replaced by the substitution of information at system program level. This paper explains the development of embedded transmission simulator for the verification of TCU firmware function which covers shifting control and on-board diagnosis. The embedded simulation program is executed in TCU processor along with the TCU firmware and it provides TCU firmware with not only the speed information those are appropriate both in driving and shifting conditions, but also the fault detection signals. Experimental results show that the validity of embedded simulator and its usefulness to the TCU firmware development and verification.

• Tribology and Lubricants
• /
• v.33 no.6
• /
• pp.269-274
• /
• 2017

Currently, fuel efficiency becomes one of critical issues for automotive industries as concerns about environmental and energy problems grow. In an automatic transmission of an automobile, a drag torque due to a viscous drag of a fluid between friction and clutch plates is one of factors that degrade fuel economy. In this work, the drag torque characteristics of a wet clutch was experimentally investigated with respect to rotational speed, temperature of automatic transmission fluid (ATF), and gap between friction and clutch plates. The experimental results showed that drag torque increases to a certain level, and then decrease to the steady state value with increasing rotational speed. This behavior may be associated with two-phase flow of air and ATF at gap between friction and clutch plates. Also, it was found that the maximum drag torque value decreased as ATF viscosity decreases with increasing temperature. However, it was shown that the point at which the maximum drag torque occurs was not significantly affected by the ATF temperature. In addition, maximum drag torque was found to decrease as the gap between friction and clutch plates increased from 0.1 mm to 0.2 mm. Furthermore, it was observed that the generation of maximum drag torque was delayed as the gap increased. The outcomes of this work are expected to be helpful to gain a better understanding of drag torque characteristic of a wet clutch, and may therefore be useful in the design of wet clutch systems with improved performance.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.25-32
• /
• 2010

A geortor type pump is widely used in lubrication and actuator systems. Especially the pump is an essential machine element of an automotive engine to feed lubrication oil and power source of automatic transmission. A gerotor is a planar mechanism consist of a pair of rotor and circular tooth of stator assembly which forms a closed space. However, related industries do not have necessary technology to design and optimize the pump and paid royalties of gerotor profile on an advanced company. Also, gerotor profiles with setting design parameter have not been sufficiently analyzed from a theoretical view. Therefore, it is very difficult for designer to decide the specifications of the gerotor profiles, and calculation and fluctuation of flow rate is not yet confirmed. In this study, theoretical analyses and optimal design of the gerotor profiles have been performed numerical method by mathematical base. An automated design system of the tooth profile has been developed through MATLAB GUI Program considering various design parameters.