• 대한조선학회논문집
• /
• 제31권2호
• /
• pp.38-44
• /
• 1994

1960년대 Auto-Pilot 시스템이 대양을 항해하는 선박에 장착되면서 운항경제성 및 선원 승선감의 견지에서 Auto-Pilot시스템의 제어 알고리듬이 연구되기 시작하였다. 초기에는 PD제어로 시작하였으나 잦은 타동작으로 인한 기구 마모를 줄이기 위해 실제 선수각과 설정선수방위 차가 어느 상한치 이상에서만 타각을 조작하는 on-off 제어를 도입하였다. 본 논문에서는 Auto-Pilot 시스템의 제어 알고리듬에 optimal제어, adaptive제어 등을 적용하여 제어기법간의 비교를 cost function을 통하여 수행함으로써 Auto-Pilot 시스템에 대한 최적의 제어기법을 조사하였다. Adaptive 제어를 위한 선박 조종운동방정식의 parameterization 과정을 검토하였고 adaptive 알고리듬의 장점이 파라미터 추정이 잘못된 경우의 수치시뮬레이션 결과로부터 분명히 알 수 있었다.

• 한국화재소방학회논문지
• /
• 제24권3호
• /
• pp.106-112
• /
• 2010

본 연구는 제연구역 출입문의 자동폐쇄장치의 개발을 위한 기초 연구의 일환으로 자동폐쇄장치의 운동해석을 수행하였다. 본 연구는 자동폐쇄장치의 프로세스와 자동폐쇄조절장치의 운동 메커니즘 정립과 기구 모델링을 바탕으로 자동폐쇄장치의 해석이론을 정립하였고, 해석이론을 바탕으로 한 운동해석 시뮬레이션을 통해 폐쇄력 장치를 선정하고 자동폐쇄조절장치의 각 요소를 설계할 수 있는 엔지니어링 데이터 축과 원천기술을 확립하였다. 따라서 본 연구로부터 자동폐쇄장치 개발의 유연성과 탄력성을 줄 수 있고, 또한 자동폐쇄장치의 개발로 인한 연기의 제어수단과 기술적 대책을 마련하고 제연시스템의 높은 신뢰성과 안정성을 확보할 수 있을 것으로 본다.

• 한국항행학회논문지
• /
• 제13권6호
• /
• pp.813-819
• /
• 2009

무인항공기의 에일러론 및 플랩, 엘리베이터 등을 제어하기위한 작동기들은 구조적으로 Time variant한 비선형적인 특성을 가지고 있을 뿐 아니라, 비행 중에 풍향 및 풍량에 따라 모델링하기 힘든 외란이 발생할 경우가 많이 발생하기 때문에 우수한 제어성능을 보이는 제어기 설계에 많은 어려움이 있었다. 본 논문에서는 기존의 PID 제어기의 장점을 그대로 살리면서 실시간으로 변화하는 시스템에 adaptive하게 대응할 수 있고 Auto gain tuning을 이용하여 개발자의 시간과 노력을 현저히 줄일 수 있는 Fuzzy Auto gain tuning PID 제어 알고리즘을 비행체 Actuator 제어에 적용한 연구내용을 기술하였다.

• 한국해양공학회지
• /
• 제16권1호
• /
• pp.64-70
• /
• 2002

This paper shows the results of the development of a small size of digital type continuous and intermittent welding auto-carriage based on microprocessor (Intel 80196KC) for welding process with long welding line. The developed welding auto-carriage loads welding torch and tracks welding line. It is an automaton largely used for welding process with a lot of long welding lines such as shipbuilding and structure. Most traditional auto-carriages have been developed based on analog circuit for open loop control. So this analog circuit welding auto-carriage cannon control welding speed. Specially welding auto-carriage for intermittent welding condition is so complicated and has the low precision of control performance in welding distance and non-welding distance. The auto-carriage developed in this paper has the following characteristics: It has not only functions of traditional carriage but also functions such as pseudo-welding process of big iron structures, intermittent welding in order to limit heat for welding thin plates, crater treatment of the final step of welding, acceleration at the initial step of welding and deceleration in the final step of welding. The main control board of auto-carriage, power supply system and DC motor drive wee developed and manufactured. The welding speed and the welding distance of the developed auto-carriage are controlled accurately by feedback control using photo-sensor. Hardware and software robust against the heat and noise produced on the welding process are developed.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.203-206
• /
• 1998

This paper describes the procedure of getting information about auto-tuning of PID regulator by the injection of high step input, called limited input, during a transient time of control. The key point is that system identification and control could be continuously executed. This means that the system information obtained by limited input despite of system uncertainty can be continuously applied to the PI regulator. Simulation and experiment result of brushless DC motor system having monotone increasing step response demonstrate the usefulness of proposed auto-tuning algorithm.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권2호
• /
• pp.347-360
• /
• 2014

The auto-berthing of a ship requires excellent control for safe accomplishment. Crabbing, which is the pure sway motion of a ship without surge velocity, can be used for this purpose. Crabbing is induced by a peculiar operation procedure known as the push-pull mode. When a ship is in the push-pull mode, an interacting force is induced by complex turbulent flow around the ship generated by the propellers and side thrusters. In this paper, three degrees of freedom equations of the motions of crabbing are derived. The equations are used to apply the adaptive backstepping control method to the auto-berthing controller of a cruise ship. The controller is capable of handling the system non-linearity and uncertainty of the berthing process. A control allocation algorithm for a ship equipped with two propellers and two side thrusters is also developed, the performance of which is validated by simulation of auto-berthing.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1008-1011
• /
• 1996

Most control systems of power plants are using classical PID controllers for their process control. In order to get the desired control performances, the correct tuning of PID controllers is very important. Sometimes, it is necessary to retune PID controllers after the change of system operating condition and system design change, etc. Commercial auto-tuning controllers such as relay feedback controller can be used for this purpose. However, using these controllers to the safety-critical systems of nuclear power plants may be cause of unsafe operation, because they are using test signals for tuning. A new system identification auto-tuning method without using test signal has been developed in this paper. This method uses process input/output signals for system identification of unknown control process. From the model information of control process which was obtained from system identification approach, the optimal PID parameters can be calculated. The method can be used in the safety-critical systems because it is not using test signals during system modeling process.

• 한국전기전자재료학회논문지
• /
• 제16권4호
• /
• pp.351-357
• /
• 2003

An easy learning elevator originated is opened to compare the existed teaming equipment, and it had a high studied efficiency that the sequence control circuit can open and close with the wire. The structure of equipment to be controlled from the first floor to the fifth floors is demostrated by the constructive apparatus with the lamps to express the function of the open-close of the door according to the cage moving with a mechanical actuation of the forward reverse breaker and the motor of load, and the mechanical actuation of hand-operation control components of push-button S/W and L/S and relay etc. These components let connect each other in order to control of the elevator function with the auto program and the designed sequence control circuit. Consequently the cage could go and come till 1∼5 steps with an auto program of the elevator and the sequence control circuit. The sequence control circuit is controlled by the step of forward and reverse to follow as that the sensor function of L/S1 ∼ L/S5 let posit with the control switchs of S/W1 ∼ S/W5 of PLC testing panel and switchs of S/W1 ∼ S/W5 installed on the transparent acryl plate of the frame. In here, improved apparatus is the hand-auto operation combined learning equipment to study the principle and technique of the originate sequence control circuit and the auto program of PLC.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.62-62
• /
• 2000

An auto-tuning PID controller which is adequate for temperature control is developed based on relay-control and pole-placement Using the critical frequency which is obtained from relay-control parameters of assumed model are identified. Pole/zero-placement PID controller is designed for the identified model. The desired pole/zeros are determined so that the closed-loop has overshoot free step response. The developed auto-tuning PID controller was successfully applied to the temperature control of RTP.

• Transactions on Control, Automation and Systems Engineering
• /
• 제1권2호
• /
• pp.141-146
• /
• 1999

This paper describes the communication method of an auto-startup system. The Auto-Startup system is designed to operate a nuclear power plant automatically during the startup operation . In general , the operations during startup in existing plant have only been manually controlled by the operator. The manual operation caused to the operator mistake. The Auto-Startup system consists of the Distributed Control System(DCS) and G2 (Expert System). Also, Functional Test Facility(FTF) provides the plant's real-data for an Auto-Startup system. So, it is necessary to develop the communication method between these systems. We developed two methods ; one is a network and the other is a hardwire line. To communicate between these systems (DCS-G2 and DCS-FTF) , we developed the communication program. In case of DCS-FTF, we used the TCP/IP and VXI. BUt, in case of DCS-G2 , we , what it called , developed the bridge program using the GSI(G2 Standard Interface). We test to check the function of the important parameter, in time, for analysis of the developed communication method. The results are a good performance when we check the communication time of important parameter. We conclude that Auto-startup system could save heat-up time about at least 5 hours and reduced the change of the reactor operation and trip.