• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.628-631
• /
• 2003

In this paper, 2.4 GHz WLAN BPF(Band Pass Filter) using LTCC(Low temperature cofiring ceramic) multilayer technology was simulated and manufactured. A modified ${\lambda}/4$ Hair-pin resonator with shunt-to ground loaded capacitor is used to shorten resonator length and improve circuit Q factor. Proposed BPF has a combline structure. Electro-magnetic Coupling between coupled strip-line resonators is controlled to provide attenuation poles at finite frequencies. The overall size of the filter is $3.2{\times}1.6{\times}1.3mm^3$. The measured result shows good agreement with simulated data.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1872-1875
• /
• 1998

In the industrial motor drive system, a shaft torsional vibration is often generated when a motor and a load are connected with a flexible shaft. This paper treats the vibration suppression control of such a system. Recently, there are new methods which estimate unknown state variables by using a reduced order observer and feedback these state variables by using a pole placement design method. But there is a trade-off between the fast command following property and the attenuation of disturbances and vibrations in these design methods. In this paper, the vibration suppression control of a two-mass system using a reference model is proposed. Because of using a reference model, the proposed control satisfy the fast command following property and the attenuation of disturbances and vibrations. Control parameter can be changed to maintain high system performance in control using a reference model. Experimental results show the validity of the proposed state feedback control using a reference model, and this controller is compared with the state feedback controller.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3A
• /
• pp.171-178
• /
• 2003

In this paper, We has proposed two DGS(Defected Ground Structure) resonators and designed the low-pass filter using the proposed DGS types. This structure consists of two rectangular slots, a ‘II type’ slot on the ground plane, and the stub at the transmission line. It has strong advantages that can vary the return loss at the passband freely and also can easily tune the attenuation pole frequency at the stopband. For enhancing the poor skirt property at the cutoff frequency of the Single Stub ‘II Type’ DGS cell, we have obtained the steep slope attenuation characteristic by combining the rectangular slot on both sides of the DGS. This type of the LPF with the proposed structure can be made more smaller than the existing filters and be used to find the various applications for eliminating the hamonics and spurious mode at WLL and the 2.4 GHz ISM band systems.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.676-679
• /
• 2001

A low-temperature cofired-ceramic (LTCC) multi-layer ceramic (MLC) band-pass filter (BPF) is presented, which has the benefits of low cost and small size. The BPF is designed for a IMT-2000 handset. The computer-aided design technology is also presented. The BPF with an attenuation pole at below the passband has been discussed and realized. The equivalent circuit of the BPF was established by transmission lines and lumped capacitors. The frequency characteristics of the LTCC-MLC BPF is well acceptable for IMT-2000 application.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.333-337
• /
• 2003

In this paper, 5.2 GHz WLAN BPF(Band Pass Filter) using LTCC(Low temperature co-firing ceramic) Multilayer technology was simulated and manufactured. A DGS(Defected Ground structure) resonator with spiral ground pattern is used to shorten resonator size and improve circuit Q factor. And the equivalent circuit of BPF was suggested. The measured result shows good agreement with simulated data. Experimental results show the center frequency of 5.25GHz, the insertion loss of 0.14dB, and the 3-dB bandwidth of 350MHz (6%). The center frequency of BPF is 5.25GHz which is available for wireless LAN.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.5
• /
• pp.482-488
• /
• 2009

Dancer system is typically used equipment for attenuation of tension disturbances. In industrial converting machines, a composite type of dancer system is applied which is mixture of active and passive dancer. It includes feedback position control loop of roll with pendulum dancer and its characteristics is different from passive and active one. In this paper, a mathematical model of the pendulum dancer was derived including PI position feedback controller and it was analyzed by using a pole-zero map and bode plot under various conditions. It was found out that velocity, length of span and inertia were associated with the performance of regulation. It was suggested that the length of upstream span should be greater than that of the downstream and the inertia should be smaller for improvement of the performance. The results can be used for design guidelines of the industrial dancer system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.237-242
• /
• 2002

In this paper, active inverter bandpass filters using the impedance matching method are designed and fabricated. The designed active inverter bandpass filter is fabricated using microstrip-lines matching networks for IMT-2000 applications. Measured results show that the two-pole inverter bandpass filter for IMT-2000 application has its insertion gain of 14.1 ㏈, 75 MHz bandwidth at the center frequency 2.18 GHz and more than 23 ㏈ attenuation at fo $\pm$ 200 MHz.

• Journal of electromagnetic engineering and science
• /
• v.11 no.2
• /
• pp.91-96
• /
• 2011

In this paper, we propose a microstrip bandpass filter using stepped-impedance coupled-line hairpin resonators. The stepped-impedance coupled-line hairpin resonator has extended harmonic suppression in comparison with a conventional hairpin resonator due to transmission zero and the movement of harmonic frequencies resulting from the stepped-impedance characteristic. A high-pass type impedance/admittance inverter is employed in order to improve the lower frequency skirt characteristics of the passband. A 4-pole bandpass filter is designed and fabricated at 1.8 GHz. The measured results show the excellent attenuation performance at the stopband which is greater than 30 dB up to 10 GHz.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.1
• /
• pp.29-34
• /
• 2007

The input and output impedances in a low voltage distribution system is one of the most important matters for power line communication because from the viewpoint of communication, the attenuation characteristic of the high frequency signals is greatly caused by impedance mismatch during sending and receiving. The frequency range is from 1MHz to 30MHz. Therefore, this paper investigates the input and output impedances in order to understand the characteristic of high frequency signals in the low voltage distribution system between a pole transformer and an end user. For power line communication, the model of Korea's low voltage distribution system is proposed in a residential area and then the low voltage distribution system is set up in a laboratory. In the low voltage distribution system, S parameters are measured by using a network analyzer. Finally, input and output impedances are calculated using S parameters.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.56-60
• /
• 2002

A low-temperature cofired-ceramic (LTCC) multi-layer ceramic (MLC) band-pass filter (BPF) is presented, which has the benefits of low cost and small size. The BPF is designed for an IMT-2000 handset. The computer-aided design technology is also presented. The BPF with an attenuation pole at below the passband has been discussed and realized. The equivalent circuit of the BPF was established by transmission lines and lumped capacitors. The frequency characteristics of the LTCC-MLC BPF is well acceptable for IMT-2000 application.