• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1248-1253
• /
• 2008

The MCS(Micro-Coplanar Strip) line with ground has been analyzed. The conformal mapping method is used to calculate the quasi-static effective dielectric constant and characteristic impedance of this MCS line. The computed results of the present work are found to be in good agreement when compared with the results obtained using commercial S/W, IE3D. And in this paper, the stepped-impedance low pass filter is designed and fabricated with MCS lines for improving the frequency responses. The LPF proposed structure has been also designed and implemented to have the sharp attenuation characteristics in stop band. The agreement between simulation and measurement results verify the implemented LPF.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.164-173
• /
• 2009

In this paper, two new circuit structures for European and U.S. ultra-wide band(UWB) bandpass filters(BPFs) with sharp roll-off characteristics are introduced. We show first that the ultra-wide bandpass property is obtained from a $\lambda$/4 open T resonator with a capacitively coupled $\lambda$/4 short-circuited line, which provides two attenuation poles at lower and upper cutoff frequencies. Then, two identical capacitively coupled input/output lines, which can be $\lambda$/4-length open ends or $\lambda$/2-length short ends, with the T-resonator, are adopted to suppress lower and higher frequency components outside of the pass band. There is coupling between the input and output lines providing two additional transmission zeros in the lower and upper transition bands of the filter. Since the coupling between the T-resonator with the $\lambda$/4 short-circuited line and the input/output lines limits the bandwidth of the filter to the European UWB band, both the $\lambda$/4 short-circuited line and the input/output lines are inserted between the two stacked T-resonators for the U.S. UWB band. The filter structures are simulated with ADS and HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape which has the dielectric constant of 7.8. Measurement results agree well with HFSS simulation results.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.8
• /
• pp.583-590
• /
• 2003

For the preestimate of the vibration level of the ground next to a dwelling, a multivariate statistical analysis on the experiment data acquired from a variety of construction sites was performed, and then a new estimate model for the value of K and n that can be applied in the diagnosis of the damage was offered. The results maybe summarized as follows : First, the $K_{95}$ and n showed high correlation at P$\leq$0.05. Specially the correlation coefficient about $W_{max}$, S were higher in $K_{95}$ than in n. indicating that $K_{95}$ is generally associated with source conditions. Second, the factor analysis permitted to identify two major sources in each fraction. These sources accounted for at least 73 % of valiance of $K_{95}$. Third, the multiple regression model for the estimate of $K_{95}$ was developed from Fac1 which depend upon the source conditions and Fac2 which depend upon the transmission conditions. The n value is able to determine from the correlation relationship associated with $K_{95}$./.

• Nuclear Engineering and Technology
• /
• v.38 no.1
• /
• pp.99-108
• /
• 2006

SNU-RCCS is a water pool type RCCS (Reactor Cavity Cooling System) developed for VHTR (Very High Temperature Reactor) application by SNU (Seoul National University). Since radiation heat transfer is the major process of passive heat removal in a RCCS, it is important to determine the precise emissivity of the reactor vessel. Review studies have used a constant emissivity in the passive heat removal analysis, even though the emissivity depends on many factors such as temperature, surface roughness, oxidation level, wavelength, direction, atmosphere conditions, etc. Therefore, information on the emissivity of a given material in a real RCCS is essential in order to properly analyze the radiation heat transfer in a VHTR. The objectives of this study are to develop a method for compensation of the factors affecting the emissivity measurement using an infrared thermometer and to estimate the true emissivity from the measured emissivity via the developed method, especially in the SNU-RCCS environment. From this viewpoint, we investigated factors such as the attenuation effect of the window, filling gas, and the effect of background radiation on the emissivity measurements. The emissivity of the vessel surface of the SNU-RCCS facility was then measured using a sight tube. The background radiation was subsequently removed from the measured emissivity by solving a simultaneous equation. Finally, the calculated emissivity was compared with the measured emissivity in a separate emissivity measurement device, yielding good agreement with the emissivity increase with vessel temperature in a range of 0.82 to 0.88.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.931-935
• /
• 2003

A multilayer two-stage LC bandpass filter using low-temperature cofired-ceramic(LTCC) is proposed in this paper. The proposed bandpass filter is composed of two ceramic substrates with different dielectric constant instead of single ceramic material from top to bottom layer. Inductive elements are designed in a low permitivity ceramic layer to reduce parasitic effects and loss, while capacitive elements are designed in a high permitivity ceramic layer for size reduction. The proposed filter has 950 MHz center &equency, 118 MHz tractional bandwidth, and 3.5 dB insertion loss. And, the total size of this filter is 2.5${\times}$2.5${\times}$l.4mm$^3$. The performance of filter is analyzed by changing coupling capacitance between each resonator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.114-117
• /
• 2006

The air filter in engine intake system has a function of filtrating the dirt in the scavenging air as well as attenuating the noise. The noise attenuation within the air cleaner filter, however, has been regarded as negligible by the field engineers. In this paper, for the analysis of the acoustical performance of air filter, an acoustical model was suggested and the characteristics of air filter system were investigated. Fibrous structure of the filter element was modeled as a micro-perforated panel using the flow resistivity and porosity. The pleated geometry of the filter element was modeled as two coupled ducts that have permeable walls, in which each duct area was assumed being constant. Using such simplified geometry, a mathematical model was developed for the sound propagation within a narrow duct system. Visco-thermal effect was considered in modeling the sound propagation through such tubes; the filter box was modeled as a rigid rectangular box. By combining two models, a four-pole transfer matrix was derived. For the validation purpose, transmission loss was measured for a plastic rectangular box containing an air filter. A noticeable effect of the air filter element was observed by including the filter into the box. Comparing the predicted and measured data, we found that the predicted TL agrees well with experimental results, in particular, in magnitude and frequency at TL troughs.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.362-367
• /
• 1987

Cylinder pressure level is defined the value of sound pressure level derived from relations of pressure and frequency which are obtained Fourier series expansion of cylinder pressure. CPL is alone in general use in combustion analysis without regarding attenuation coefficient determined by engine structure because it is almost constant in various kinds of engines. Combustion pressure fluctuation and influence of CPL was investigated in this paper using Wiebe combustion function superposition th obtain the effect of premixed and diffusive combustion. The results are as follow. (1) Influence of combustion maximum pressure(P$\sub$max/) on CPL is correspond with total energy per cycle well. (2) P$\sub$max/, .DELTA.P$\sub$max/, (dp/d.theta.)$\sub$max/ and (d$\^$2/p/d.theta.$\^$2/)$\sub$max/ are very effective on CPL in the range of low frequency, mid-low frequency, mid-high frequency and high frequency respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.8
• /
• pp.1313-1321
• /
• 2000

This paper presents a novel HTS microstrip pseudo-lumped element resonator for the compact and simple filter design. A 7-pole bandpass filter with quasi-elliptic response is designed and fabricated using non-adjacent couplings between resonators. A seven-pole quasi-elliptic filter is fabricated using double sided YBCO on a LaAlO$_3$ substrate with thickness of 0.5 mm and dielectric constant of 23.5. The filter has an insertion loss of 0.8 dB at 20K, a bandwidth of 8 MHz at the center frequency of 1774 MHz, and an attenuation of 33 dB for the cut-off-band of 1 MHz.

• Journal of Biosystems Engineering
• /
• v.14 no.3
• /
• pp.168-180
• /
• 1989

This study was attempted to develop the electronic-hydraulic hitch control system for position control of tractor plow and investigate the control performance of the system through experiments. Experiments were carried out to investigate the responses of the system to the step and sinusoidal inputs in position control. The effects of control mode, hydraulic flow rate, reference deadband, and proportional constant on control performance of the system were investigated. The following conclusions were derived from the study; 1. For the position control system operated on on-off control mode, positions of implement were controlled within ${\pm}0.73^{\circ}{\sim}{\pm}1.46^{\circ}$ in rockshaft angle to the reference position when the hydraulic flow rates were 5~15 l/min. For the position control system operated on PWM control mode, positions of implement were controlled within ${\pm}0.73^{\circ}$ to the reference position regardless of hydraulic flow rates. It means that the implement could be positioned more accurately to the reference position on PWM control mode than on on-off control mode. 2. As results of the frequency responses of the position control systems, no clear difference in control performance between on-off control and PWM control modes was found. As the hydraulic flow rates increased, the corner frequencies of amplitude attenuation and phase-angle change increased. It means that the control performance of the system could be improved as the hydraulic flow rate increases.

• Journal of Biosystems Engineering
• /
• v.32 no.4
• /
• pp.237-246
• /
• 2007

In this study, the microwave free-space transmission technique was used to measure the dielectric property of powdered food at microwave frequencies. The sample holder was designed and fabricated to transmit the microwave signals ranging from 1 to 15GHz. From the microwave propagation theory the equation expressing the dielectric property of powdered food was derived and validated by standard dielectrics. The dielectric property of powdered food such as wheat flour, coffee powder and milk powder was measured and analyzed. In the uniform range of bulk density of material, the real parts of permittivity of the food samples increased with the increase of moisture content, bulk density and temperature of the samples. The propagation properties such as attenuation and phase shift increased linearly as the moisture density of the food samples increased. As a measuring frequency of the moisture content, the X-band was recommended.