• Journal of Korean Society of Water and Wastewater
• /
• v.10 no.1
• /
• pp.112-120
• /
• 1996

In this study, the porous glass media was utilized as biomass carrier, and the optimum characteristics of this new media in fixed bed biofilm process were investigated. The characteristics of media considered here are a void volume fraction, a specific surface area, and surface characteristics of media. The effect of surface roughness and material could be clearly demonstrated by the fact that the porous glass media showed a good potential for biofilm development. This might results from the fact that biofilm is initially formed in the surface cavities of the media is protect from the shear effect. Therefore, the microcolonies are not readily detached by the fluid shear. In the steady state, biofilm formation along the packing bed depth was different from media to media. The specific area was also an important factor for the attachment of microorganism on the media surface. The specific area was also an important factor for the attachment of microorganism on the media surface. In the case of porous glass media, about $100m^2/m^3$ was enough to obtain a good organic removal efficiency The organic removal efficiency could be improved by increasing the void volume fraction in the reactor, at least 80% was required to obtain a high removal efficiency and prevent clogging. From the analysis of kinetics study, the yield coefficient, Y, was 0.42 mgMLSS/mgSBOD, endogenous respiration coefficient, ke, was $0.12day^{-1}$ and substrate removel coefficient of Mckinney. km, was $16.8hr^{-1}$ for the porous glass media G-2

• Journal of the Korean Vacuum Society
• /
• v.22 no.6
• /
• pp.298-305
• /
• 2013

Uniform silica nanobeads were synthesized by St$\ddot{o}$ber method and assembled in the form of monolayer on glass substrate using sonication method. Before the assembly of silica nanobeads, glass substrates were treated with molecular linkers, such as CP-TMS and PEI, and nanobeads were dispersed in toluene. In attachment test, SO (sonication without stacking) method and SS (sonnication with stacking) method was used and sonication time was controled. After the experiment, microbalance was use to measure deviation between before and after the attachment experiment then calculate percent of coverage. Minutely observe with SEM (Scanning Electron Microscopy) then select the most close-packed and monolayer assembled cover glass and calculate DOC (Degree of Coverage). In SO method, DOC increased very sharply and reach over 140 percent point, also got lots of multi-layer region. On the other hand, in SS method DOC increased slower than SO method but more close-packed and monolayer assembled.

• Journal of Periodontal and Implant Science
• /
• v.41 no.2
• /
• pp.73-78
• /
• 2011

Purpose: For periodontal tissue engineering, it is a primary requisite and a challenge to select the optimum types of cells, properties of scaffold, and growth factor combination to reconstruct a specific tissue in its natural form and with the appropriate function. Owing to fundamental disadvantages associated with using a two-dimensional substrate, several methods of seeding cells into three-dimensional scaffolds have been reported and the authors have asserted its usefulness and effectiveness. In this study, we explore the cell attachment of periodontal ligament fibroblasts on nanohydroxyapatite (n-HA) scaffold using avidin biotin binding system (ABBS). Methods: Human periodontal ligament fibroblasts were isolated from the health tooth extracted for the purpose of orthodontic procedure. HA nanoparticles were prepared and $Ca(NO_3)_2-_4H_2O$ and $(OC_2H_5)_3P$ were selected as precursors of HA sol. The final scaffold was 8 mm in diameter and 3 mm in height disk with porosity value of 81.55%. $1{\times}10^5$ periodontal ligament fibroblasts were applied to each scaffold. The cells were seeded into scaffolds by static, agitating and ABBS seeding method. Results: The number of periodontal ligament fibroblasts attached was greater for ABBS seeding method than for static or agitating method (P<0.05). No meaningful difference has been observed among seeding methods with scanning electron microscopy images. However, increased strength of cell attachment of ABBS could be deduced from the high affinity between avidin and biotin ($Kd=10^{-15}\;M$). Conclusions: The high-affinity ABBS enhances the ability of periodontal ligament fibroblasts to attach to three-dimensionally constructed n-HA scaffold.

• Journal of Periodontal and Implant Science
• /
• v.31 no.1
• /
• pp.21-41
• /
• 2001

The goal of Periodontal treatment is predictable periodontal regeneration. But until now, many products including GTR materials and growth factors are beyond of complete regeneration. BMP can induce ectopic bone formation when implanted into sites such as rat muscle and can greatly enhance healing of bony defects when applied exogenously. BMP can promote periodontal regeneration by their ability to stimulate new bone and new cementum formation. But little is known about optimal conditions required for the application. Root conditioning is used for bioacive root change so altered root surface provides a substrate that promotes chemotaxis, migration and attachment of peridontal cells encouraging connective attachment to the denuded root surface. The aim of this study is to investigate whether the acid conditioning change effect of rhBMP-2 on human periodontal ligament cell and osteoblast cell line. 288 periodontally involved root dentin slices are divided into 6 groups, each 48, 1)control, 2)treated with BMP, 3)treated with citric acid 4)treated with citric acid+BMP 5)treated with tetracycline 6)treated with TC+BMP. Each group was devided half, so 12 root dentin slices were seeded with periodontal ligament cells and 12 were seeded with osteoblasts. At day 2 and 7, cell number, protein assay, ALP activitiy was measured. To investigate morphology of cultured cells, SEM was employed. Statistical analysis was performed with SPSS 8.0 either t-test or ANOVA test. The results are ; Protein assay and cell number was slightly decreased in CA+BMP group compared to Ca group but it was not statistically significant and ALP activity was much more increased in CA+BMP group compared to CA group so there was no statistically significance between BMP and CA+BMP group and statistically significant compared to control group. Cell number and protein assay was slightly increased in TC group and ALP activity was much less the BMP group and CA group. Cell number and protein and ALP activity was not much increased in TC+BMP group. TC group and TC+BMP group showed cell morphology change in SEM. This results suggested that application of root surface with citric acid before BMP treatment might give better result in periodontal regeneration.

• Applied Microscopy
• /
• v.41 no.2
• /
• pp.139-145
• /
• 2011

Parthenocissus tricuspidata is an epiphyte that lacks a main axial stem, but develops adhesive disks along the stem for climbing support. In this study, scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) were utilized to examine the brick wall surface and the adhesive disks of P. tricuspidata that attached to the surface successfully. The study was mainly focused the outermost layers of both structures before and after adhesion to find out whether there has been some structural and/or physical interactions between the two. The adhesive disks adhered firmly to the brick wall by secreting adhesive materials that help them for a tight attachment to the surface. The rough wall surface appeared facilitating better attachment of the adhesive disks by infiltrating the materials into those spaces leading to some degree of interactions at the interface. EDS analysis on the outermost layers of the adhesive disks that were separated from the substrates was also consistent with the SEM data on the interaction between the adhesive disks and the substrate surface. EDS analysis of the brick wall surface and the adhesive disks demonstrated similar elements of O, Si, Fe, Al, K, Mg, and Na in their components.

• Macromolecular Research
• /
• v.15 no.4
• /
• pp.348-356
• /
• 2007

The aim of this study was to fabricate a submicro-and micro-patterned fibronectin coated wafer for a cell culture, which allows the positions and dimensions of the attached cells to be controlled. A replica molding was made into silicon via a photomask in quartz, using E-beam lithography, and then fabricated a polydimethylsiloxane stamp using the designed silicon mold. Hexadecanethiol $[HS(CH_2){_{15}}CH_3]$, adsorbed on the raised plateau of the surface of polydimethylsiloxane stamp, was contact-printed to form self-assembled monolayers (SAMs) of hexadecanethiolate on the surface of an Au-coated glass wafer. In order to form another SAM for control of the surface wafer properties, a hydrophilic hexa (ethylene glycol) terminated alkanethiol $[HS(CH_2){_{11}}(OCH_2CH_2){_6}OH]$ was also synthesized. The structural changes were confirmed using UV and $^1H-NMR$ spectroscopies. A SAM terminated in the hexa(ethylene glycol) groups was subsequently formed on the bare gold remaining on the surface of the Aucoated glass wafer. In order to aid the attachment of cells, fibronectin was adsorbed onto the resulting wafer, with the pattern formed on the gold-coated wafer confirmed using immunofluorescence staining against fibronectin. Fibronectin was adsorbed only onto the SAMs terminated in the methyl groups of the substrate. The hexa (ethylene glycol)-terminated regions resisted the adsorption of protein. Human dermal fibroblasts (P=4), obtained from newborn foreskin, only attached to the fibronectin-coated, methyl-terminated hydrophobic regions of the patterned SAMs. N-HDFs were more actively adhered, and spread in a pattern spacing below $14{\mu}m$, rather than above $17{\mu}m$, could easily migrate on the substrate containing spacing of $10{\mu}m$ or less between the strip lines.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.467-472
• /
• 2002

Long Carbon Nanotubes(CNTs) were cut by diamond lapping film followed by observation using SEM. The paste was prepared by mixing shortened CNT powder, ${\alpha}$-terpineol used as a solvent, and ethylcellulose as a binder. This paste was deposited on glass substrate by screen printing and extruded by syringe. After screen printing, several post-treatments were performed to control the alignment of CNTs perpendicular to the substrate. The deposited CNTs were scratched by sand paper or diamond lapping film. It was also treated by attachment followed by an immediate detachment using the adhesive tape. SEM observation indicates that excellent vertical alignment of CNTs could be achieved by simple post-treatments from the screen printed-CNTs paste. Similar alignment of CNTs is also observed in the as-extruded CNTs paste.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.521-524
• /
• 2001

The anaerobic continuous reactor, which was filled with a sludge of anaerobic digestion from Sooyoung sewage treatment plant, was supplied with synthetic wastewater of various concentration. After changing to substrate concentration, 디 1is research indicated that attached biomass was kept constant after attachment 23 days. In SEM photographs. shape and structure of biofilm could be observed, but bacteria species and methanogens were not identified. A large number of methanogenic bacteria were showed on the surface of PE substratum by fluorescence under 480nm of radiation.

• BMB Reports
• /
• v.32 no.6
• /
• pp.547-553
• /
• 1999

Aminoacyl-tRNA synthetases are essential enzymes catalyzing the attachment of specific amino acids to cognate tRNAs. In the present work, the substrate analogue L-methionine hydroxamate was used to identify functional residues located in the active site of the E. coli methionyl-tRNA synthetase (MetRS). This compound inhibited bacteria, yeast, and human MetRS activities to a similar degree, suggesting a conserved active site structure and mechanism between MetRSs of different phylogenetic domains. Mutants of the E. coli MetRS resistant to methionine hydroxamate were also isolated. These mutants contained a substitution either at T10, Y15, or Y94. These residues are highly conserved among the different MetRSs and the mutants showed decreased aminoacylation activity, suggesting their functional and structural significances. The putative roles of these residues are discussed on a structural basis.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.409-414
• /
• 2007

Wettability of solid surfaces with liquids is governed by the chemical properties and the microstructure of the surfaces. We report on the preparation of liquid-repellent surfaces using surface-attached monolayers of perfluorinated polymer molecules on porous silica substrates. A covalent attachment of the polymer molecules to the substrate is achieved by generation of the polymer chains through starting a surface-initiated radical-chain polymerization of a fluorinated monomer. To this, self-assembled monolayers of azo initiators are attached to silica substrates, which are used to kick off the polymerization reaction in situ. The growth of the fluorinated polymer films and the characterization of the obtained surfaces by surface plasmon spectroscopy, XPS, and contact angle measurements is described. It is shown that perfluorinated polymer films can be grown with controlled thicknesses on flat and even on porous silica surfaces, essentially without changing the surface roughness. The combination of the low surface energy coating and the surface porosity allows generation of materials which are both water and oil repellent.