• 한국농촌건축학회논문집
• /
• 제15권4호
• /
• pp.35-42
• /
• 2013

The study aims to investigate general characteristics of Jae-sil from an architectural perspective by grasping location, deployment, structure, and plan composition based on existing inhabited conditions in Jeollabukdo. Results derived from the study are as follows. First, the location of Jae-sil is classified into mountainous and village types, and the two types showed a similar distribution. The village type showed the most distribution in the foot of a mountain in the rear of village, while the mountainous type is close to graveyard. The Jae-sil were mostly exposed to south, southeast, and southeast, which was not significantly different from residence. For deployment of the Jae-sil, a "二" shaped house, where main quarter and gated building are parallel located, can be common, indicating that additional attached building is less required. Second, for the platform out of structural components, coursed masonry was conducted by using natural rocks, and placed were a prop on the platform, first line on processed foot stone, and others on natural foot stone. For pillar, front line round columns, while others square columns. The binding type of the upper part of pillar is dominated by jangyeosujang and sorosujang. For wooden frame structure, 5ryangs were the most distributed, and out of these, 1goju 5ryang was the most generally used. For a roof part, it was composed with gambrel roof with single eave, and the roof was constructed by placing traditional Korean tile roof on the top. Third, for a size of Jae-sil out of plan composition, although the facade and the side of it were presented in a diverse manner, 4 facade rooms and 1.5 side rooms were the most frequently presented, and all Jae-sil were equipped with front ceremonial space. For spatial composition of Jae-sil, main floored hall is placed at the center, and each room is placed on the left and right side to secure space for ancestral rite for participants of it, and for a house with 5 rooms or more, it shows that main floored hall and rooms are weighted from side to side.

• 한국의류산업학회지
• /
• 제20권2호
• /
• pp.128-142
• /
• 2018

This study explores newborn clothing with regard to clothing type, construction, textiles, design, size, and label placement. Related consumer complaints are also analyzed. Analysis of 50 newborn clothing items revealed six types of newborn clothing: baenaet jeogori, baenaet gown, bodysuit, one-piece, shirt and pants set, and pants. The baenaet jeogori was the most common type, and the most commonly used fasteners were ties and snaps. The following characteristics were commonly observed: front opening, long raglan sleeves, mitten cuffs, cotton fabric, white/ivory color, animal print, contrast hem, $appliqu{\acute{e}}$, and size 60. In-depth interviews of 12 mothers with children under 24 months revealed that the baenaet jeogori was the most unsatisfactory type; the shirt and pants set and bodysuit were preferred. Interviewees were dissatisfied with types of openings, expressing a preference for snaps and complaining about ties, too many snaps, metal snaps, and shoulder openings. Overly wide or narrow sleeves resulted in improper fit, and long sleeves made it difficult to dress the baby. Interviewees required diverse sleeve length options. They were dissatisfied with heavy fabric for hot and warm seasons, and with labels attached inside clothing or outside near the neckline. Mothers with particularly small or big babies complained about limited sizes. To improve current newborn clothing, additional items such as shirt and pants sets or individual pants, front opening clothing with few snaps, proper sleeve fit with diverse length options, lightweight fabric for hot and warm seasons, label placement that avoids skin irritation, and size segmentation are recommended.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.167.1-167.1
• /
• 2011

Sustainable energy generation is becoming extremely imperative due to the expected limitations in current energy resources and to reduce pollution. Especially, because of its considerable energy potential, ocean wave energy has been investigated with regard to power generation. To develop large high power wave generator system, it is important to make a small scale proto type and to test that. Thus the objective of this research is to examine the characteristics of a mechanically excited generator system having small power capacity experimentally. The water reservoir (4 m length, 1.5 m width and 1.8 m depth) having a wave maker to make arbitrary height and period of the water wave was made. The proto type consists of three main parts; a buoy, rack-pinion base one-way mechanism, and a wave generator(Fig.1). The water wave is going up and down and the hexahedron buoy is following the wave. The rack gear attached to the buoy is also going up and down to roll the pinion connected to an electric generator then it produces electricity. The experiments were performed with several conditions of water waves, and the power outputs over 30 W could be measured for some conditions. In future works, to achieve higher performance for the proto type, the effects of primary parameters (buoy shape and mass, etc.) on the system efficiency will be identified.

• 한국발생생물학회지:발생과생식
• /
• 제22권3호
• /
• pp.263-273
• /
• 2018

Aquaporin (AQP) 3, a facilitated transporter of water and glycerol, expresses in placenta and fetal membranes, but the detailed localization and function of AQP3 in placenta remain unclear. To elucidate a role of AQP3 in placenta, we defined the expression and cellular localization of AQP3 in placenta and fetal membranes, and investigated the structural and functional differences between wild-type and AQP3 null mice. Gestational sacs were removed during mid-gestational period and amniotic fluid was aspirated for measurements of volume and composition. Fetuses with attached placenta and fetal membranes were weighed and processed for histological assessment. AQP3 strongly expressed in basolateral membrane of visceral yolk sac cells of fetal membrane, the syncytiotrophoblasts of the labyrinthine placenta and fetal nucleated red blood cell membrane. Mice lacking AQP3 did not exhibit a significant defect in differentiation of trophoblast stem cells and normal placentation. However, AQP3 null fetuses were smaller than their control litter mates in spite of a decrease in litter size. The total amniotic fluid volume per gestational sac was reduced, but the amniotic fluid-to-fetal weight ratio was increased in AQP3 null mice compared with wild-type mice. Glycerol, free fatty acid and triglyceride levels in amniotic fluid of AQP3 null mice were significantly reduced, whereas lactate level increased when compared to those of wild-type mice. These results suggest a role for AQP3 in supplying nutrients from yolk sac and maternal blood to developing fetus by facilitating transport of glycerol in addition to water, and its implication for the fetal growth in utero.

• Journal of Biosystems Engineering
• /
• 제33권3호
• /
• pp.204-209
• /
• 2008

The power strength of electric wave of reader looked radiation forms from the gate type RFID system. The more distant from antennas, the weaker of power strength of electric wave. The power strength of electric wave with 3 antennas showed stronger than its with 2 antennas. With 2 antennas, the coefficient of correlation between the power strength of electric wave and response ability of tag was 0.665 (p=0.009), and it showed results at significance level. With 3 antennas, the coefficient of correlation was 0.711 (p=0.004), correlationship between the power strength of electric wave and the response ability of tag showed at significance high level. From the analysis result about tag reading performance on the gate type RFID system, the reading rate was good when tags were attached on a acrylic plate which were located in front of 3 or 4 antennas. As tags were getting away from antennas, the reading rate was decreased. The nearer from antennas, the higher the reading rate at the center. When tags were turned at right angles with antennas, the longer distant from antennas, the lower reading rates at the center, right and left locations. When the number of antennas and distance are constant, respectively, the significant difference of the tag reading rates according to the locations of left, right and center were not found.

• 한국안전학회지
• /
• 제32권4호
• /
• pp.129-136
• /
• 2017

This study investigated the probability of possible accident through qualitative and quantitative analysis of the pressure safety valve types installed in facilities using high pressure gas to compare the installation domestic and foreign pressure safety valve standards sought the safety characteristics and safety improvement direction accordingly. The three types are the case where the shut-off valve is not installed at the front of the PSV (Case A), If a shut-off valve is installed at the front of the PSV for inspection (Case B) and If a shut-off valve is installed in front of PSV (C.S.O), PSV is installed in parallel (Case C). Three types of cases were compared with FTA and HAZOP. The results of study of the possible accidents due to over-pressure safety valve installation type, used in a high-pressure gas facilities was shows in the following order Case B > Case A > Case C. The results of analysis through FTA was in order to protect the reservoir for the possible occurring of accident the safety valve installation is depend on its type. In the FTA analysis, defects in the device itself which attached to the storage tank as a substitute for analysis of the probability of operator mistakes was Case B with as high as $2.01{\times}10^{-6}$. Depending on the type of installation analysis of Case B in order to ensure safety is prohibited to install shut-off valve and believes that mandatory regulations are needed. Rationally installing of pressure safety valve in the high pressure using facilities will be expected to improve the industrial safety from severe accidents such as high-pressure gas fire explosion.

• Journal of Biosystems Engineering
• /
• 제34권6호
• /
• pp.397-403
• /
• 2009

This study was carried out to investigate the present status of subsoil compaction, and subsoil compaction management in orchard as a basic study for developing a self-propelled explosive subsoiler. Subsoil compaction was evaluated using the soil penetration resistance. Soil cone index was measured using the DIK 5520 type cone penetrometer in several fruit farms such as apple, pear, peach and grapes during growing seasons of these fruit in Jecheon, Gamgok, Choongju, Cheonan and Hwasung areas. Most of the subsoil managing machinery were either explosive type or digging type attached to the tractor or power tiller and turning radius of this machine was more than 3-5 m. Many of the farmers wanted to use the subsoiler which can put lime into soil and rupture soil at the same time. For most of the orchard fields, soil penetration resistance in vehicle traffic area was increased quickly and reached about 1.0 MPa in 5 cm soil depth. As the soil depth increased to 15-20 cm, cone penetration resistance reached about 2.0-2.5 MPa which restricted root growth seriously. Thus it was concluded that one of the main reason for increasing the soil compaction in orchard fields is agricultural vehicle traffic. In the vicinity of fruit trees, compaction is not so serious compared to that of the vehicle traffic area, but as the soil depth increased to 20-25 cm, in most of the orchard fields soil penetration resistance reached about 2.0-2.5 MPa which is the root growth-limiting value. Considering the rooting depth of fruit trees which ranged 30-60 cm for apple, pear and peach, and 20-30 cm for grape, it is necessary to loosen the subosoil and improve the subsoil conditions using subsoiler.

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.19-24
• /
• 2015

Joint properties of electric control unit (ECU) module using Sn-Cu-(X)Al(Si) lead-free solder alloy were investigated for automotive electronics module. In this study, Sn-0.5Cu-0.01Al(Si) and Sn-0.5Cu-0.03Al(Si) (wt.%) lead-free alloys were fabricated as bar type by doped various weight percentages (0.01 and 0.03 wt.%) of Al(Si) alloy to Sn-0.5Cu. After fabrications of lead-free alloys, the ball-type solder alloys with a diameter of 450 um were made by rolling and punching. The melting temperatures of 0.01Al(Si) and 0.03Al(Si) were 230.2 and $230.8^{\circ}C$, respectively. To evaluation of properties of solder joint, test printed circuit board (PCB) finished with organic solderability perseveration (OSP) on Cu pad. The ball-type solders were attached to test PCB with flux and reflowed for formation of solder joint. The maximum temperature of reflow was $260^{\circ}C$ for 50s above melting temperature. And then, we measured spreadability and shear strength of two Al(Si) solder materials compared to Sn-0.7Cu solder material used in industry. And also, microstructures in solder and intermetallic compounds (IMCs) were observed. Moreover, thickness and grain size of $Cu_6Sn_5$ IMC were measured and then compared with Sn-0.7Cu. With increasing the amounts of Al(Si), the $Cu_6Sn_5$ thickness was decreased. These results show the addition of Al(Si) could suppress IMC growth and improve the reliability of solder joint.

• 한국의상디자인학회지
• /
• 제22권2호
• /
• pp.19-28
• /
• 2020

This study investigated the annual frequency and clothing type by extracting puff sleeves designs from overseas fashion collections from S/S and F/W 2017 to S/S and F/W 2019. Specifically, it analyzed production characteristics and pattern methods by the type of puff sleeve design, and found the following: In terms of the percentage of puff sleeves by season, S/S 2019 was the highest. Since Newtro, with a 1990s sensitivity, was the mainstream trend during the S/S 2019, power puff sleeves, a signature of the Newtro style, accounted for the greatest portion of this design feature. In terms of the type of clothes with puff sleeves, 'dress' (54.3%) was the highest, followed by 'shirts/blouse' (27.5%), 'jacket/coat' (12.5%), and 'padded coat/jacket' (5.7%). Specifically, puff sleeve patterns were found mostly in the 'dress' category, more than 47% every season, while the figures were more than 23%, 9.3%, and 2.6% in 'shirts/blouse', 'jacket/coat' and 'padded coat/jacket', respectively. In other words, puff sleeve designs were more common in 'dress' or 'shirts/blouse' than in a 'padded coat/jacket'. In general, the shoulder length is reduced to prevent the shoulders from looking broader because of puffs. In contrast, recent puff-sleeve styles differ from those introduced by modern fashion designers in that they have drop shoulders with puffs attached. Furthermore, as constructive and over-exaggerated sleeve patterns appeared, puffs were applied to diverse sleeve styles including mutton leg and Mameluke styles. The analysis results of this study will contribute to the development of the fashion industry through small quantity batch production pursuing unique styles and serve as the basis for further studies on the configuration methods of puff sleeves. This study will be used in various ways, including as educational material on sleeve patterns. Through the analysis of sleeve patterns, this study tries to provide basic data for planning the design of puff sleeves and helping to diversify the ladies' apparel market in the future.

• Journal of Periodontal and Implant Science
• /
• 제40권6호
• /
• pp.257-264
• /
• 2010

Purpose: Connective tissue reattachment to periodontally damaged root surfaces is one of the most important goals of periodontal therapy. The aim of this study was to develop a root conditioning agent that can demineralize and detoxify the infected root surface. Methods: Dentin slices obtained from human teeth were treated with a novel root planing agent for 2 minutes and then washed with phosphate-buffered saline. Smear layer removal and type I collagen exposure were observed by scanning electron microscopy (SEM) and type I collagen immunostaining, respectively. Cell attachment and lipopolysaccharides (LPS) removal demonstrated the efficiency of the root conditioning agent. Results: SEM revealed that the smear layer was entirely removed and the dentinal tubules were opened by the experimental gel. Type I collagen was exposed on the surfaces of the dentin slices treated by the experimental gel, which were compared with dentin treated with other root planing agents. Dentin slices treated with the experimental gel showed the highest number of attached fibroblasts and flattened cell morphology. The agar diffusion assay demonstrated that the experimental gel also has effective antimicrobial activity. Escherichia coli LPS were effectively removed from well plates by the experimental gel. Conclusions: These results demonstrated that this experimental gel is a useful tool for root conditioning of infected root surfaces and can also be applied for detoxification of ailing implant surface threads.