• 한국정밀공학회지
• /
• 제27권1호
• /
• pp.11-17
• /
• 2010

This study investigates the non-traditional manufacturing process of dry wire electrical discharge machining (EDM) in which liquid dielectric is replaced by a gaseous medium. Wire EDM experiments of thin workpieces were conducted both in wet and dry EDM conditions to examine the effects of spark cycle (T), spark on-time ($T_{on}$), thickness of work pieces, and work material on machining performance. The material removal rate (MRR) in the dry wire EDM case was much lower than that in the wet wire EDM case. In addition, the thickness of workpiece and work-material were found to be critical factors influencing the MRR for dry EDM process. The relative ratios of spark, arc and short circuit were also calculated and compared to examine the effectiveness of processes of dry and wet wire EDM.

• 한국전기전자재료학회논문지
• /
• 제15권6호
• /
• pp.551-557
• /
• 2002

Carbon nitride films have been deposited on Si(100) substrate by a high voltage discharge plasma combined with laser ablation in a nitrogen atmosphere. The films were grown both with the without the presence of an assisting focused Nd:YAG laser ablation. The laser ablation of the graphite target leads to vapor plume plasma expending into th ambient nitrogen arc discharge area. X-ray photoelectron spectroscopy and Auger electron spectroscopy were used to identify the binding structure and the content of the nitrogen species in the deposited films. The nitrogen content of the films was found to increase drastically with an increase of nitrogen pressure. The surface morphology of the films was studied using a scanning electron microscopy. Data of infrared spectroscopy and x-ray photoelectron spectroscopy indicate the existence of carbon-nitrogen bonds in the films. The x-ray diffraction measurements have also been taken to characterize the crystal properties of the obtained films.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.165-169
• /
• 2001

Carbon nitride films were grown on Si (100) substrate by a laser-electric discharge method with and without a magnetic field assistance. The magnetic field leads to vapor plume plasma expending upon the ambient arc discharge plasma area. Influence of the magnetic field has resulted in increase of a crystallite size in the films due to bombardment (heating) of Si substrates by energetic carbon and nitrogen species generated during cyclotron motion of electrons in the discharge zone. Many crystalline grains were observed in the morphology of the deposited films by scanning electron microscopy. In order to determine the structural crystalline parameters, X-ray diffraction (XRD) was used to analysis the grown films.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권12호
• /
• pp.673-678
• /
• 2000

The dielectric barrier discharge(DBD) is a common method to create a nonthermal plasma in which electrical energy is used to create electrons with a high average kinetic energy. The unique aspect of dielectric barrier discharges is the large array of short lifetime(10ns) silent discharges created over the surface of the dielectric. A silent discharge is generated when the applied voltage exceeds the breakdown voltage of the carrier gas creating a conduction path between the applied electrode and grounded electrode. As charge accumulates on the dielectric, the electric field is reduced below the breakdown field of the carrier gas and the silent discharge self terminates preventing the DBD cell from producing a thermal arc. In fact, the most significant application of dielectric barrier discharges is to generate ozone for contaminated water treatment. Therefore, experiments were perfomed at 1∼2[bar] pressure using a coaxial geometry single dielectric barrier discharge for ozone concentrations and energy densities. The main result show that the concentration and efficiency of ozone are influenced by gas nature, gas quantity, gas pressure, supplied voltage and frequency.

• 한국대기환경학회지
• /
• 제30권4호
• /
• pp.339-349
• /
• 2014

$CO_2$ emission has been gradually increased due to rising fossil fuel use. A gliding arc plasma scrubber (GAPS) was proposed to destruct $CO_2$. For optimum design of GAPS, a CFD analysis has been conducted in different configuration for the system. The parameters considered included gas injection velocity at the nozzle and gas flow rate to gap between electrodes. The reactor configuration affected velocity fields which caused changes in the mixture fraction and the retention time. The mixing effect of $CO_2$ and supplied gas ($CH_4$ and steam) was enhanced by installing a orifice baffle. This revealed that the orifice baffle is effective in $CO_2$ conversion by positioning the reactants in the gas into the center of plasma discharge.

• 한국수소및신에너지학회논문집
• /
• 제10권1호
• /
• pp.1-7
• /
• 1999

In order to study on the effect of fabrication methods on the changes of hydrogenation properties of FeTi alloy, FeTi samples were prepared using three different methods, i.e., arc melting, mechanical alloying and combination of the two methods. The FeTi prepared by mechanical alloying represented amorphous structure. The hydrogen storage capacity of arc melted FeTi alloy is larger than any other samples. However, FeTi electrode fabricated by mechanical alloying after arc melting showed largest discharge capacity among them.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2009년도 학술발표회 초록집
• /
• pp.1052-1056
• /
• 2009

본 연구에서는 대상 지점의 강우량자료와 유출수문곡선으로 전 기간에 대한 유출률과 특정기간을 갖는 유출률을 각각 산정하여 유출특성을 분석하였다. 본 연구를 수행하기 위해서 GIS 소프트웨어인 ArcInfo와 ArcView 등으로 대상유역의 유역도, 강우관측망도, 수위관측망도, 수계망도,티센망도 등을 생성하여 대상유역의 수계 특성을 파악하였다. 개발된 곡선식의 적정성을 판단하기위해 상 하류 간의 유출특성 등을 비교 분석하였으며, 유역 내 댐이나 저수지가 존재할 경우 이를 고려하였다. 유출률 산정결과, 이호대교(남한강 본류) 지점에서의 유출률은 방류량을 고려하지 않았을 경우 59.8%, 고려했을 경우 74.5%로 산정되었다. 흑천의 원덕교 지점에서는 67.1%, 경안천의 경안교 지점에서는 78.3%, 홍천강의 성포교와 남산교 지점은 각각 63.3%, 53.1%로 산정되었다. 따라서 개발된 수위-유량관계곡선식은 적정한 것으로 판단되며, 이에 근거하여 유출수문곡선은 양질의 수준인 것으로 평가되었다.

• 한국진공학회지
• /
• 제6권S1호
• /
• pp.137-140
• /
• 1997

A cathodic arc with beam filter is employed for the deposition of metallic and hydrogen-free amorphous carbon films. A solenoid filter is used to prevent macropaticles and nonionized atoms from reaching the substrate. The detail transport characters of the filter are presented in the paper. With an optmum filter arrangement we are able to obtain a filter output of 18.4% of the total number of ions produced by the vacuum arc discharge. The deposited amorphous cabon thin film contains no hydrogen and a high fraction of $sp^3$ is determined by XPS. A dense Ti film deposited on H13 steel improves the corrosion resistance of the H13 steel and significant improvements of corrosion resistance were observed by implanting Ti, C in the film.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1898-1900
• /
• 1996

The Laser aided diagnostic method makes it possible to diagnose plasma characteristics which have never been done by other one. The aim of this study is to measure the electron density profile of an arc plasma by Mach-Zenhder interferometer. The two laser beams (He-Ne and Argon Lasers), which are different in wavelength, pass across an arc plasma and meet a change of refractivity which makes fringe shifts. From this effects we could find densities of electron and neutral particle.

• 한국레이저가공학회지
• /
• 제5권3호
• /
• pp.15-20
• /
• 2002

The principal obstacle to selection of a laser processing method in production is its relatively high equipment cost and the natural unwillingness of production supervision to try something new until it is thoroughly proven. The major objective of this work is focused on the combined features of gas tungsten arc and a low-power cold laser beam. In this work, the laser beam from a 7 watts carbon monoxide laser was combined with electrical discharges from a short-pulsed capacitive discharge GTA welding power supply. When the low power CO laser beam passes through a special composition shielding gas, the CO molecules in the gas absorbs the radiation, and ionizes through a process blown as non-equilibrium, vibration-vibration pumping. The resulting laser-induced plasma(LIP) was positioned between various configurations of electrodes. The high-voltage impulse applied to the electrodes forced rapid electrical breakdown between the electrodes. Electrical discharges between tungsten electrodes and aluminum sheet specimens followed the ionized path provided by LIP. The result was well-focused melted spots.