• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.194-196
• /
• 2006

This paper deals with design of a small-scaled permanent magnet generator (PMG) for wind power applications. First, this paper determines rated power and rated speed of the PMG from measured characteristics of wind turbines. Second, we derive analytical solutions for the open-circuit field in order to determine optimum magnet thickness and pole pitch/arc ratio. Third, on the basis of open circuit field solutions, stator magnetic circuit is designed. And then, a diameter of stator coil which agree with a required current density is calculated, and its turns are determined from the area of slot. Finally, finite element (FE) method is employed for validity of the designed PMG and, the back-emf measurements are also given to confirm the design.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.125-127
• /
• 2003

The single phase switched reluctance motor(SRM) is more simpler and robust in the structure than poly phase SRM. It has the merits that it reduces the switching elements and the energy density per volume is very high. Recently, it has been researched and developed in various types and starting method due to the technique of power electronics and the computer added design. The single phase SRM is tried to apply to many industrial appliance field to substitutethe the induction motor by the single phase SRM. On the previous studies, we decided the design parameters of the single phase SRM for the blower driver to adapt the design method of the conventional machine and the poly phase SRM. In this studies, it is proposed the conditions to decide the optimal pole arcs because the stator and rotor pole arcs is very important in the characteristics of the single phase SRM. For this reason, it is analysed the characteristics of current on/off angle vs. pole arc, pole arcs vs. average torque.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.81-92
• /
• 1996

This study is to compare the weldability of Zircaloy-4 end cap of nuclear fuel pin using by GTA and Nd :YAG LB. The welding parameters which affect bead width and penetration depth have been investigated. The effect of joint geometry of end cap for GTAW and LBW has been studied and optimum conditions of Zircaloy-4 endcap welding have been found. Microstructures and microhardness of GTA and LB welded zones have been also compared.

• Korean Journal of Organic Agriculture
• /
• v.12 no.1
• /
• pp.67-80
• /
• 2004

Farm economy is getting worse because of the free trade trends in agriculture sector and unreasonable application of market economy principles to agricultural products. And The worldwide issues of environmental pollution as well as want of food, water and energy make human future be anxious. In addition, consumers raise questions in argument about safety of foods produced by traditional farming or imported. So I propose the urban-rural living community movement(URLCM) as an alternative plan for sustainable domestic agriculture. URLCM based on environmentally friendly agriculture and community consciousness will be able to solve many of present issues on agriculture and rural society through incessant interchanges between urban and rural community. This URLCM has to be basically founded on principles of symbiosis-coexistence and life circulation. So those that have to be driven forward arc organizing producers and consumer cooperatives, making environmentally friendly rural region and products, combining with consumer cooperatives, training the participants and so forth.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.173-173
• /
• 2003

Nanowire와 nanorod 같은 1차원의 반도체 재료는 디멘젼과 크기와 물리적 특성과의 관계 등을 연구하는데 중요한 역할을 하며 laser ablation, arc discharge, chemical vapor depostion, vapor phase transport Process와 solution등의 방법으로 성공적으로 합성되었다. ZnO 는 3.37eV의 넓은 밴드갭과 다른 넓은 밴드갭 재료에 비해 높은 exciton bindng energy (60meV)를 가지며 UV LED, laser diode에 적용하기 유리하고 최근 디스플레나 나노 광전소자로서의 가능성 이 대두되면서 최근 이에 관한 연구가 증가하고 있다. 본 연구에서는 열적탄소환원법(carbothermal reduction process)으로 ZnO와 graphite 분말을 1:1 중량비로 혼합한 분말을 90$0^{\circ}C$, 100$0^{\circ}C$에서 air 분위기에서 20분간 반응 후 로 내에서 냉각 하였다. 직경 이 50nm-1000nm, 길이가 수 미크론인 내부 결함이 전혀 없는 육각형 단결정의 nanowire가 합성되었고 XRD, FE-SEM과 TEM으로 조성 및 형상, 내부구조를 분석하였다. 합성된 ZnO nanowire는 직경 이 변하는 부분에서 성장방향으로의 계단을 형성하였고 이는 layer by layer 방법으로 nanowire가 성장한다는 것을 나타낸다.

• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.4
• /
• pp.143-148
• /
• 2002

Method of plasma-immersion ion deposition of hydrogenated DLC films on relatively thick flat dielectric substrates from plasma of not-self-sustained low-pressure gas arc discharge is suggested. Coating properties have been investigated experimentally, average energy Per a deposited carbon atom depending on discharge current has been calculated. Optimum deposition parameters lot obtaining sufficiently hard and transparent high-adhesive a-C:H films on a 4-mm thick glass substrates have been determined. Possibility to use these coatings for photo-tools protection from abrasion wear at low operating loads is shown in general.

• Journal of Biosystems Engineering
• /
• v.13 no.3
• /
• pp.81-90
• /
• 1988

Agricultural and municipal wastes arc serious nuisance. in Korea. Disposal of these wastes by land application, incineration or burial have created serious environmental problems such as air pollution and ground water contamination. Uncomposted waste materials are also potential sources of plant and soil pathogens. As available sites for waste burial become more difficult to find and air quality standards for incineration become stricter, composting as a method for treating solid wastes will become more attractive. This article discussed the recent topics on composting to further develop a rational strategy. The future of composting is developed based on the interacting factors of the price of energy and fertilizer, public policy, economic considerations, and biotechnology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.175-178
• /
• 1995

Distribution of relaxation time is presented in the Cole-Cole arc diagram with frequency parameter. In the case of estimation of activation energy for main chains, maximum loss frequencies of ${\alpha}$ peaks, f$\sub$m/(${\alpha}$) display curved change according to the WLF type with variations of temperature. Structural change by the filling of filler and degradation by the thermal aging can be estimated from the WLF factors, C$_1$and C$_2$in Log f$\sub$m/-1/T curves which reflect the variations of free volume and thermal expansivity of composites.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.123-124
• /
• 2006

This study aimed at exploiting low heat input characteristic of laser welding to effectively control grain coarsening in the fusion zone(FZ) and heat affected zone(HAZ) of 1.5mm thick 18wt% Cr ferritic stainless steel weld. The study demonstrated that as compared with gas tungsten arc welding(GTAW), laser welding brought about significant grain refinement in the FZ and HAZ. However, the impact absorbed energy of GTA weld was superior than that of laser weld because the strengthening effect during welding and cooling stage was higher In laser weld than that in GTA weld. The coarser grains in each weld than base metal resulted in an inferior toughness.

• Korean Journal of Materials Research
• /
• v.12 no.8
• /
• pp.676-681
• /
• 2002

Microstructure, mechanical properties, and oxidation resistance of TiAIN thin films deposited on quenched and tempered STD61 tool steel by arc ion plating were studied using XRD, XPS and micro-balance. The TiAIN film was grown with the (200) orientation. The grain size of TiAIN thin film decreased with increasing Al contents, while chemical binding energy increased with Al contents. When hard coating films were oxidized at $850^{\circ}C$ in air, oxidation resistance of both TiN and TiCN films became relatively lower since the surface of films formed non-protective film such as $TiO_2$. However, oxidation resistance of TiAIN film was excellent because its surface formed protective layer such as $_A12$$O_3$ and $_Al2$$Ti_{7}$$O_{15}$, which suppressed oxygen intrusion.