• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.52-57
• /
• 2005

The increasing automobiles continue to cause air-pollution problem s worse than ever. In fact, many automobile research are involved in how to reduce exhaust emissions effectively specially in $NO_X$ and PM to comply with stringent emission standards, Euro V. This research emphasized on the development of continuous regeneration DPF technology which was one of promising removing technology of particulate matters because of its comparability and high applicability. In addition, this research discussed on some design points of view through correlation study by com paring the experimental data with computational results by the introduction of commercial codes such as CFD-ACE+ and KIVA-3V. The numerical simulation on the performance of continuous regeneration DPF apparatus and corresponding emission characteristics has been predicted well enough and verified with experimental results. The pressure and average temperatures are decreased to about 2.6% and 1.4% respectively under a full engine load condition mainly due to back pressures raised by diesel particulate filter. Pressure, temperature and heat releasing rates tend to decrease specially at higher engine load, but they are not affected at lower engine load regions.

• 보건행정학회지
• /
• 제10권4호
• /
• pp.1-19
• /
• 2000

We have witnessed several kinds of new discourses and practices in health and medicine since the 1970s, such as popular concerns with alternative or complementary medicine, inordinate attention to the promotion of 'healthy' living, rapid resurrection of traditional medicine and ecological management of health. Four structural and situational factors are discussed to underlie these new trends：(i) as 'crisis' in health care of the 1970s was translated into health care reform of the 1980s backed up by neo-liberal political philosophy, the state responsibility for nation's health is being transferred to the individual ；(ii) it resulted from the limits of biomedical paradigm in dealing with chronic diseases；(iii) medico-scientific knowledge of disease is transformed into the subjective discourses and technologies of health in postmodern society ； and (iv) it is deeply associated with the considerable increase in environmental risk perception of health and disease. There are some inherent countervailing forces in these new discourses and practices. First, while they derive from lifestyle-oriented behavioral change, medicalization of life and death is still consolidated in the new trends. Second, inasmuch as new tides are reliant upon science, they. are likely to be remote from techne that means not the practical application of theoretical knowing but a special form of practical knowing. Third, as new discourses and activities accomplished＇in the name of health＇increasingly occupy important strategies in forming the self-identity, they serve as moral apparatus which involves prescriptions about how we should live our lives and conduct our bodies, both individually and collectively. Therefore, two points are suggested to consider seriously whether these streams will succeed in improving the‘healthy’living of all the people. Instead of limiting tile perspective to medicine, healing and health care, a new matrix that interweave welfare, ecology and labor along with them is timely needed for enhancing the health for all. In addition, as the World Health Report fm strongly shows, inequality in health heavily depends upon socio-economic development of a society, and it is not the richest countries that have the best health status, but those that have the smallest income differences between rich and poor.

• Parasites, Hosts and Diseases
• /
• 제23권2호
• /
• pp.247-252
• /
• 1985

In the present study, the effect of primary infection to reinfection with Ascaris suum larvae was experimented in mouse model. Mice were challenged with 1,000 infective stage eggs of Ascaris suum. The embryonated eggs were directly introduced into stomach of mice. Reinfection was performed at 50 days after the primary infection with same method as primary infection. Mice were sacrificed 3, 5, 7, 10, 15 and 20 days after infection in both groups respectively. Larvae collected from livers and lungs with Baermann's apparatus were enumerated and measured after sacrifice. Sera of mice were also collected at same time. The results of the experiment were as follows: With antigen prepared from coelomic fluid of adult Ascaris suum and sera collected from mice before reinfection, the production of antibody in experimental mice was confirmed by the gel-diffusion technique. In the livers of reinfected mice, the larvae were recovered up to 10 days after challenge, otherwhile in the primary infected mice, the larvae were observed up to 7 days. The maximum number of larvae were observed in the lungs of primary infected mice on 10 days after inoculation. In the lungs of reinfected mice, maximum number of larvae were recovered on 7 days after, only few larvae were recovered on 10 days after reinfection. As regards the growth of the larvae, the third stage larvae, over $500{\mu\textrm{m}}$ in length, appeared in livers at 5 days after reinfection, but it couldn't be found on 7 days and 10 days after challenge. The third stage larvae continuously developed were observed in lungs of mice from 5 days after reinfection. In conclusion, it was found that development of larvae in livers of immune mice were probably repressed by the immune mechanisms being rises in livers and defence mechanism is also acting by interfering with the process of larval penetration into the lung from the liver.

• 해양환경안전학회지
• /
• 제19권1호
• /
• pp.59-65
• /
• 2013

최근 몇 년간 에너지 위기에 대한 우려가 급격히 증가하고 있으며, 방대한 에너지소비에 따른 환경오염도 큰 문제로 대두되고 있다. 사회적으로 에너지 위기가 고조되고 있는 가운데 새로운 에너지나 신재생에너지에 대한 관심이 증가하고 있다. 본 연구는 이러한 문제를 해결하기 위한 하나의 해결책으로 양어장 등에서 사용되는 폭기장치를 구동하기 위한 에너지를 자연으로부터 얻을 수 있는 가능성을 타진해 본 연구이다. 연구의 목적은 풍력에너지를 이용한 폭기장치의 개발에 있으며, 다양한 풍속 및 수풍면적에 대한 풍력폭기장치의 가능성을 살펴보고 있다. 또한, 최대의 효율을 얻을 수 있는 풍력펌프의 각도에 대한 토출구의 높이를 유도하여 유사한 장치의 설계에 있어 도움을 줄 수 있는 데이터를 제공하고 있다.

• 한국광학회지
• /
• 제3권4호
• /
• pp.227-233
• /
• 1992

분할디스크형 글라스레이저 증폭기를 개발하기 위하여 이를 해석 설계할 수 있는 시뮬레이션 코드를 작성했다. 레이저매질에서의 열부하를 감소시키고, 플래시램프의 방사스펙트럼과 레이저글라스의 흡수 스펙트럼 간의 결합효율을 높이기 위해서는 전류밀도를 2000-4000A/$\textrm{cm}^{2}$로 유지하여 단파장에서의 방사에너지를 줄여야 한다. 디스크 증폭기에서 같은 부피를 갖는 매질을 3등분하여 냉각표면적을 3배로 늘렸을 때 온도상승치는 30% 정도로 떨어졌다. 단면펌핑 분할 디스크형 증폭기의 설계에서는 각 글라스 간의 $Nd^{3+}$ 도핑율에 차등을 주어야 하고 플래시램프 앞에 있는 매질의 흡수계수 $\alpha$ 와 두께 d의 곱인 $\alpha$d가 0.26 전후가 적절하다는 것을 알았다.

• 한방안이비인후피부과학회지
• /
• 제17권3호
• /
• pp.26-32
• /
• 2004

Objective: The aim of this work is to investigate the antibacterial activity of the essential oil obtained from Artemisia lavandulaefolia (A. lavandulaefolia), as the development of microbial resistance to antibiotics make it essential to constantly look for new and active compounds effective against pathogenic bacteria. Method: The aerial parts of A. lavandulaefolia (1 kg) were subjected to steam distillation for 3 h, using a modified Clevenger type apparatus in order to obtain essential oil. Diethyl ether was the extracting solvent kept at 25?. The essential oil were analyzed by gas chromatography (GC) and gas chromatography／mass spectrometry (GC／MS). The essential oil and the composition were tested for antimicrobial activities against 15 different genera of oral bacteria. Ninety-nine compounds accounting for 94.74$\%$<／TEX> of the oil were identified. The main compounds in the oil were 1,8-cineole (5.63$\%$), yomogi alcohol (4.49$\%$), camphor (4.92$\%$), a-caryophyllene (16.10$\%$), trans-a-famesene (5.09$\%$), a-terpineol (3.91$\%$), borneol (5.27$\%$), cis-chrysanthenol (6.98$\%$), and a-humulene oxide (3.33$\%$). The essential oil and its compounds were tested for antimicrobial activity against 10 different genera of oral bacteria. Conclusion: The essential oil of A. lavandulaefolia exhibited considerable inhibitory effects against all obligate anaerobic bacteria (MICs, 0.025 - 0.05 ㎎／ml) tested, while their major compounds demonstrated various degrees of growth inhibition

• 대한한의학회지
• /
• 제17권1호
• /
• pp.222-233
• /
• 1996

In order to understand the stimulation quality of Artemisine Vulgaris Folium(Bong), Mori Ramulus(Sangi) and Persicae Ramulus(Dogi) combustion, and get the basic data for the development of electric moxibustion apparatus, the average temperature, peak temperature, average gradient temperature, maximum gradient temperature and combustion time of heating period on the three moxa materials were measured. 1. The average combustion temperature was high in order of Dogi, Sangi and Bong, and these were acknowledged to have a significant difference each other in the average temperature. 2. The peak combustion temperature among those was high in order of Dogi, Sangi and Bong, and Bong was acknowledged to have significant differences with Dogi and Sangi. Sangi and Dogi however were not acknowledged to have difference each other. 3. The average gradient temperature among those was high in order of Dogi, Sangi and Bong, and Bong was proved to have significant differences with Dogi and Sangi. Sangi and Dogi however were not proved to have difference each other. 4. The maximum temperature among those was high in order of Dogi, Sangi and Bong, bong was acknowledged to have signigicant differences with Dogi and Sangi, but Sangi and Dogi were not proved to have difference each other. 5. The combustion time was short in order of Dogi, Sangi and Bong. Bong was acknowledged to have significant differences with Dogi and Sangi, but Sangi and Dogi were not. In order to understand well the characteristics of combustion, it is required to have a quantitative interpretation of combustion calory, and, in the future, we expect it is required to have a consistent study for the clinical effectiveness and the mutual relationship according to the combustion characteristics.

• 한국해양환경ㆍ에너지학회지
• /
• 제3권1호
• /
• pp.62-69
• /
• 2000

본 연구는 담수조류의 대량 번식에 따른 정수장의 여과막 박힘, 어류의 대량폐사 등 각종 피해를 최소화하기 위하여 응집제를 이용한 응집-여과공정을 녹조제거시스템에 적용하기 위한 것이다. 응집-여과 공정에서 최적의 응집상태를 결정하기 위하여 시료로는 낙동강 원수를 사용하였고 Jar test와 실험실용 반응기를 사용하여 알칼리도, 탁도, Chl-a, pH를 측정하였다. 응집시간, 응집제 주입량, 드럼필터 회전속도 그리고 Chl-a는 각각 5min, 5mg/l, 3rpm 그리고 90㎍/l의 조건에서 높은 조류제거율을 보였다. Alum을 사용하였을 때의 조류 및 탁도 평균제거율은 50～60%, 30～50%이었고, PAC는 Chl-a의 제거율이 Alum보다 약 20% 더 좋은 효율을 보였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.152-152
• /
• 2016

Anodizing is a technology to generate thicker and high-quality films than natural oxide films by treating metals via electrochemical methods. It is a technique to develop metals for various uses, and extensive research on the commercial use has been performed for a long time. Aluminum anodic oxide (AAO) is generate oxide films, whose sizes and characteristics depending on the types of electrolytes, voltages, temperatures and time. Electrochemical manufacturing method of nano structure is an efficient technology in terms of cost reduction, high productivity and complicated shapes, which receives the spotlight in diverse areas. The sulfuric acid was used as an anodizing electrolyte, controlling its temperature to $10^{\circ}C$. The anode was 5083 Al alloy with dimension of $5(t){\times}20{\times}20mm$ while the cathode was the platinum. The distance between the anode and the cathode was maintained at 3 cm. Agitation was introduced by magnetic stirrer at 300 rpm to prevent localized temperature rise that hinders stable growth of oxide layer. In order to observe surface characteristics with applied current density, the electrolyte temperature, concentration was maintained at constant condition for $10^{\circ}C$, 10 vol.%, respectively. To prevent hindrance of stable growth of oxide layer due to local temperature increase during the experiment, stirring was maintained at constant rate. In addition, using galvanostatic method, it was maintained at current density of $10{\sim}30mA/cm^2$ for 40 minutes. The cavitation experiment was carried out with an ultrasonic vibratory apparatus using piezo-electric effect with modified ASTM-G32. The peak-to-peak amplitude was $30{\mu}m$ and the distance between the horn tip and specimen was 1 mm. The specimen after the experiment was cleaned in an ultrasonic, dried in a vacuum oven for more than 24 hours, and weighed with an electric balance. The surface damage morphology was observed with 3D analysis microscope. As a result of the investigation, differences were observed surface hardness and anti-cavitation characteristics depending on the development of oxide film with applied current density.

• 대한인간공학회지
• /
• 제33권6호
• /
• pp.553-563
• /
• 2014

Objective: The purpose of this study was to evaluate the effect of gender (male, female) and grip spans (45, 50, 60, 70, 80mm) on total grip strength, resultant force, finger force and subjective discomfort rating. Background: In order to prevent musculoskeletal disorders, studies of hand tools need to be preceded based on grip strength, finger force, and subjective discomfort rating. However, experimental apparatus using tools such as pliers that reflect the actual work place was almost non-existent. Method: Fifty-Two (26 males and 26 females) participants were recruited from the student population. In this study, a pair of revised pliers, which can change grip span from 45 to 80mm was applied to estimate total grip strength, resultant force and individual finger forces. All participants were asked to exert a maximum grip force with three repetitions, and to report the subjective discomfort rating for five grip spans of pliers (45, 50, 60, 70, 80mm). Results: There were significant differences of total grip strength, resultant force, individual finger forces and subjective discomfort rating according to grip span. The lowest total grip strength was obtained from the grip span of 80mm for both genders. For resultant force, the highest resultant force was exerted at grip spans of 50, 60 and 70mm for females and 50 and 60mm for males. The lowest subjective discomfort rating was observed in the 50mm for both genders. Conclusion: Based on the result, 50mm and 60mm grip spans which provide the highest force and lowest discomfort rating might be recommendable for the male and female pliers users. Application: The findings of this study can provide guidelines on designing a hand tool to help to reduce hand-related musculoskeletal disorders and obtain better performance.