• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.4
• /
• pp.199-202
• /
• 2011

Ga doped ZnO thin films were deposited with RF magnetron sputtering on glass substrate without intentional substrate heating and then the effect of post deposition annealing temperature on the structural, optical and electrical properties of the films was investigated. The post deposition annealing process was conducted for 30 minutes in a vacuum of $1{\times}10^{-3}$ Torr and the vacuum annealing temperatures were 150 and $300^{\circ}C$, respectively. As increase annealing temperature, GZO films show the increment of the prefer orientation of ZnO (002) diffraction peak in the XRD pattern and the optical transmittance in a visible wave region was also increased, while the electrical sheet resistance was decreased. The figure of merit obtained in this study means that GZO films which vacuum annealed at $300^{\circ}C$ have the highest optoelectrical performance in this study.

• Journal of Powder Materials
• /
• v.13 no.1 s.54
• /
• pp.25-32
• /
• 2006

The alumina dispersion-strengthened (DS) C15715 Cu alloy fabricated by a powder metallurgy route was annealed at temperatures ranging from $800^{\circ}C\;to\;1000^{\circ}C$ in the air and in vacuum. The effect of the annealing on microstructural stability and room-temperature mechanical properties of the alloy was investigated. The microstructure of the cold rolled OS alloy remained stable until the annealing at $900^{\circ}C$ in the air and in vacuum. No recrystallization of original grains occurred, but the dislocation density decreased and newly formed subgrains were observed. The alloy annealed at $1000^{\circ}C$ in the air experienced recrystallization and grain growth took place, however annealing in vacuum at $1000^{\circ}C$ did not cause the microstructural change. The mechanical property of the alloy was changed slightly with the annealing if the microstructure remained stable. However, the strength of the specimen that was recrystallized decreased drastically.

• Journal of Magnetics
• /
• v.12 no.1
• /
• pp.49-52
• /
• 2007

We investigated annealing effect of microforged powders on magnetic properties and electromagnetic absorption behaviors for ferromagnetic Fe-Cr metal alloy powder-polymer composites. The coercive properties greatly decreased with annealing temperature and the magnetic permeability had significantly increased after microforging and subsequent annealing treatment, due to a reduction in lattice strain of the microforged powders. The power loss in the far field regime also had greatly increased after microforging and subsequent annealing treatment in frequency range from 50 MHz to 6 GHz. As a result, the electromagnetic absorption of ferromagnetic Fe-Cr alloy metal powder-polymer composites was highly improved because of the relaxation of the internal strain during annealing process.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.274-277
• /
• 2000

Thin Film Transistor(TFTs) were fabricated from poly-Si crystallized by a two-step annealing process on glass substrates. The combination of low-temperature(500$^{\circ}C$) Metal-Induced Lateral Crystallization(MILC) furnace annealing and high -temperature (700$^{\circ}C$) rapid thermal annealing leads to the improvement of the material quality The TFTs measured with this two-step annealing material exhibit better characteristics than those obtained by using conventional MILC furnace annealing.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.70-71
• /
• 2003

• Korean Journal of Optics and Photonics
• /
• v.20 no.1
• /
• pp.34-40
• /
• 2009

In-situ pulse laser (Nd-YAG, 2nd harmonics 532 nm) annealing used in physical vapor deposition of $MgF_2$, $SiO_2$ and ZnS thin films was shown to be effective in improving their surface roughness properties. Total integrated scattering (TIS) measurements of $MgF_2$ and $SiO_2$ samples deposited on glass substrates revealed that the laser irradiation of films at an energy of approximately $140\;mJ/cm^2$ at 532 nm with a repetition frequency of 10 Hz and pulse duration of 5 ns during the deposition resulted in total scatterings that were minimum. But in case of the ZnS samples, measurements revealed minimum total scattering at a laser energy of approximately $62\;mJ/cm^2$. Atomic Force Microscopy (AFM) has been used to evaluate the effect of pulse laser annealing on the surface roughness for thin film samples. The results were similar to the TIS measurements, indicating that surface roughness was decreased when the irradiated annealing pulse laser energy increased. But it also increased when the irradiated annealing pulse laser energy was over some limit that depended on the materials.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.335.2-335.2
• /
• 2016

The fixed negative charge of the Al2O3 passivation layer gives excellent passivation performance for both n-type and p-type silicon wafers. For the best passivation quality, annealing is known to be a prerequisite step and a lot of studies concerning annealing effect on the passivation characteristics have been performed. Meanwhile, for manufacturing a crystalline silicon solar cell, firing process is applied to the Al2O3 passivation layer. Therefore, study on not only annealing effect but also on firing effect is necessary. In this work, Al2O3 passivation performance (minority carrier lifetime) for p-type silicon wafer was evaluated with Quasi-Steady-State Photoconductance(QSSPC) measurement after annealing at different temperatures. For the samples which showed different aspects, C-V measurement was performed for the cause - whether it is due to the chemical effect or field-effect. The change in Al2O3 passivation property after firing processes was investigated and the mechanism for the change could be estimated.

• Transactions of Materials Processing
• /
• v.13 no.5
• /
• pp.449-454
• /
• 2004

The annealing behavior of a 5083 Al alloy deformed at cryogenic temperature was investigated, focusing on the evolution of microstructures and mechanical properties. Especially, the effects of annealing temperature, $150~300^{\circ}C$, and time, 3∼60min., on microstructures and mechanical properties of the sheets received 85% reduction at cryogenic temperature were investigated. The optimization of the annealing conditions resulted in a mixture of equiaxed grains and elongated subgrains, exhibiting a good combination of uniform elongation and high strength.

• Corrosion Science and Technology
• /
• v.14 no.6
• /
• pp.296-300
• /
• 2015

ALDC8 (Al-Si-Cu) alloy has been often corroded with pattern of intergranular corrosion in corrosive environments. Thus, in order to improve its corrosion resistance, the effect of annealing heat treatment to corrosion resistance and hardness was investigated with parameters of heating temperatures such as $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$ for 1hr. The hardness was varied with annealing temperature and slightly decreased with annealing heat treatment. However, the relation between annealing temperature and hardness agreed not well each other. Corrosion potential was shifted to noble direction and corrosion current density was also decreased with increasing annealing temperature. Moreover, both AC impedance at 10 mHz and polarization resistance on the cyclic voltammogram curve were also increased with increasing annealing temperature. Furthermore, intergranular corrosion was somewhat observed in non heat treatment as well as annealing temperatures at $100^{\circ}C$, $200^{\circ}C$ and $300^{\circ}C$, while, intergranular corrosion was not nearly observed at annealing temperature of $400^{\circ}C$, $500^{\circ}C$. Consequently, it is considered that the annealing heat treatment of ALDC8 alloy may be an available method not only to inhibit its intergranular corrosion but also to improve its corrosion resistance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.3
• /
• pp.190-194
• /
• 2003

Dielectric thin films of (P $b_{0.72}$,L $a_{0.28}$) $Ti_{0.93}$ $O_3$ (PLT(28)) have been deposited on Pt(111)/Ti/ $SiO_2$/Si(100) substrates in-situ by pulsed laser deposition using different annealing and deposition Processes. We have investigated the effect of hydrogen annealing on the ferroelectric properties of PLT thin films and found that the annealing process causes the diffusion of hydrogen into the ferroelectric film resulting in the destruction of polarization. We have tried to form the film by a two-step deposition process In order to improve electrical property. Two-step process to grow PLT films was adopted and verified to be useful to enlarge the grain size of the film and to reduce the leakage current characteristics. Structural properties and electrical properties including dielectric constant, ferroelectric characteristics, and leakage current of PLT thin films were shown to be strongly influenced by grain size. The film deposited by using two-step Process including pre-annealing treatment has a strongly(111) orientation. However, the films deposited by using single -step process with hydrogen annealing process show the smallest grain size. The film deposited by using two-step process including pre-annealing treatment shows the leakage current density of below 10$^{-7}$ A/c $m^2$ for the field of smaller than 100 kV/cm. However, the films deposited by using single-step process with hydrogen annealing process and pre-annealing process show worse leakage current density than the film deposited by using two-step process including pre-annealing treatment.tment.