• E2M - 전기 전자와 첨단 소재
• /
• 제10권5호
• /
• pp.481-486
• /
• 1997

This paper describes the anisotropic etching characteristics of Si in acqueous TMAH/IPA solutions. The etch rates of (100) oriented Si crystal planes decrease with increasing TMAH concentration and IPA concentration. Etchant concentration and etch temperature have a large effect on hillock density. Hillock density strongly increase with lower TMAH concentration and higher etch temperature. The etched (100) planes are covered by pyramidal-shaped hillocks below TMAH 15 wt.%, but very smooth surface is obtained TMAH 25 wt.%. The addition of IPA to TMAH solution leads to smoother surfaces of sidewalls etched planes. Undercutting ratio of pure TMAH solution is much higher than KOH. But, addition of IPA to TMAh the underrcutting ratio reduces by a factor of 3∼4. Therefore, acqueous TMAH/IPA solution is able to use as anisotropic etchant of Si because of full compability with IC fabrication process.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제11권4호
• /
• pp.223-228
• /
• 2011

In this paper, a novel range-free localization algorithm for anisotropic networks is proposed. In the proposed method, the characteristics of the given network are considered and each sensor node estimates the relation between the hop counts and the geographical distances. Unlike most of the previous localization algorithms, the proposed method performs well not only in the isotropic network but also in the anisotropic networks. The proposed method is applied to both isotropic and anisotropic network topologies and the simulation results demonstrate that the method exhibits excellent and robust performances.

• 한국전산유체공학회지
• /
• 제8권4호
• /
• pp.6-15
• /
• 2003

It is an aim of this study to perform extensive numerical study for analyzing the anisotropic turbulence effects on spatial and temporal behaviors of droplet for impinging sprays. The turbulence model of Durbin is used for comparisons with the k-ε model. The turbulence-induced dispersions of droplets are considered to describe the anisotropy of turbulence effectively and spray/wall interactions are simulated using the model of Lee and Ryou. Present study investigates the overall and the internal structures of impinging diesel sprays such as spray shapes, radius and height of wall sprays, Sauter mean diameter (SMD), local droplet velocity, and local gas velocity and compared the results with experimental data by two adopted turbulence models. When the anisotropy effect of turbulence is included, better predictions for both gas and droplet tangential velocities are obtained, compared to the k-ε model. It is concluded that anisotropic effect of turbulence should be considered for simulating impinging diesel sprays.

• 한국농공학회지
• /
• 제44권1호
• /
• pp.103-115
• /
• 2002

During this study, various stress path tests in previous isotropic and anisotropic (compression and tension) stress histories are performed on weathered granite soil sampled at Iksan, Jeonbuk. Yielding points are determined from various stress-strain curves(stress ratio-shear strain, volumetric strain, normalized energy and dissipated total energy curves). The shape and characteristics of isotropic and anisotropic yielding curves are examined. The main results are summarized as follows . 1) Yielding curries defined from stress ratio - normarized energy and dissipated total energy curves show almost perfect ellipse. 2) Directions of plastic strain incremental vector are not perpendicular to yielding curve. 3) Normarized energy and dissipated total energy spread with similar tendency with respect to yielding currie in stress space.

• Computers and Concrete
• /
• 제5권4호
• /
• pp.417-434
• /
• 2008

This paper deals with damage induced anisotropy modeling for concrete-like materials. A thermodynamics based constitutive relationship is presented coupling anisotropic damage and elasticity, the main idea of the model being that damage anisotropy is responsible for the dissymmetry tension/compression. A strain written damage criterion is considered (Mazars criterion extended to anisotropy in the initial model). The biaxial behavior of a family of anisotropic damage model is analyzed through the effects of yield surface modifications by the introduction of new equivalent strains.

• Structural Engineering and Mechanics
• /
• 제61권2호
• /
• pp.221-230
• /
• 2017

In this paper, we investigated the propagation of thermoelastic surface waves in fibre-reinforced anisotropic general viscoelastic media of higher order of nth order including time rate of strain under the influence of rotation. The general surface wave speed is derived to study the effectsof rotation andthermal onsurface waves. Particular cases for Stoneley, Love and Rayleighwaves are discussed.The results obtained in this investigation are more general in the sense that some earlier published results are obtained from our result as special cases. Our results for viscoelastic of order zero are well agreed to fibre-reinforced materials. Comparison was made with the results obtained in the presence and absence of rotation and parameters for fibre-reinforced of the material medium. It is also observed that, surface waves cannot propagate in a fast rotating medium.Numerical results for particular materials are given and illustrated graphically. The results indicate that the effect of rotation on fibre-reinforced anisotropic general viscoelastic media are very pronounced.

• 한국지진공학회논문집
• /
• 제2권2호
• /
• pp.77-85
• /
• 1998

이방성 재료에서의 표면파 진행과 산란에 대한 연구를 수행하였다. 두 개의 이방성 4분 무한 영역의 계면에서의 표면파 산란거동을 해석하기 위한 이론을 제안하였다. Green 함수법을 이용하여 계면에서의 표면파 산란계수를 결정하기 위한 방정식을 유도하였다. 수치계산을 수행하였으며 이방성과 비균질성이 산란 거동에 미치는 영향을 비교하였다.

• 마이크로전자및패키징학회지
• /
• 제12권1호
• /
• pp.17-20
• /
• 2005

In this paper, we presented the quasi-static characteristics of novel microstrip lines with anisotropic grooved dielectric in finite metal. A quasi-static mode-matching method has been used to analyze this new structure and the simulation results are validated through comparison with other available results. The results in this paper show that it is possible to control the propagation characteristics of microstrip lines with the use of anisotropic grooved dielectric in finite metal. Also anisotropic grooved dielectric in microstrip line can be newly added to the design parameters of high performance three dimensional monolithic microwave circuits and other microwave applications.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.729-736
• /
• 2000

For nonhomogeneous and anisotropic rocks such as schist, shale, etc, a method to determine the anisotropic elastic constants was proposed. Many authors have investigated in detail the behavior elastic constants of anisotropy rocks(Pinto 1970, Amadei 1983, 1992, Amadei & Savage 1989). They concluded that equations of elastic constants E$_1$, E$_2$ and G$_2$ can be derived from the measured strains in arbitrary three directions. And, modulus of elasticity varies according to the inclination of discontinuity in specimens. If we attach three strain gages in accordance with the directions of anisotropy on the rock specimen under uni-axial compression and diametral compression tests, anisotropy elastic constants can be determined by these equations. With this method, the degree of anisotropy will be easily evaluated by simple laboratory test. This paper presents the results of elastic constants due to the angle of bedding planes of anisotropic rock, such as shale, in uni-axial compression and diametral compression tests

• 한국통신학회논문지
• /
• 제29권1C호
• /
• pp.50-58
• /
• 2004

본 논문은 수정된 이방성 확산 펄터를 이용한 영상 개선 방법을 제안하였다. 이를 위하여 최소 신뢰 스케일을 기반으로 하는 센서 잡음 추정과 스케일 스페이스 방법을 도입하였다. 이때 이방성 필터는 구해진 임계값 함수와 국부 기울기에 의해 수정되었다. 모의 실험을 통해 제안한 방법이 평탄 영역에서의 잡음을 거의 증폭시키지 않으면서도 뛰어난 에지 향상을 보임을 증명할 수 있었다.