• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.2
• /
• pp.87-96
• /
• 2004

Studies were conducted to select the candidate buffer material for a high-level waste (HLW) repository in Korea. This paper presents the hydraulic properties, the swelling properties, the thermal properties, and the mechanical properties as well as the radionuclide release-retarding capacity of Kyungju bentonite as part of those studies. Experimental results showed that the hydraulic conductivities of the compacted bentonite were very low and less than $10^{-11}$m/s. The values decreased with increasing the dry density of the compacted bentonite. The swelling pressures were in the range of 0.66 MPa to 14.4 ㎫ and they increased with increasing the dry density. The thermal conductivities were in the range of 0.80 ㎉/m $h^{\circ}C$ to 1.52 ㎉/m $h^{\circ}C$. The unconfined compressive strength, Young's modulus and Poison's ratio showed the range of 0.55 ㎫ to 8.83 ㎫, 59 ㎫ to 1275 ㎫, and 0.05 to 0.20, respectively, when the dry densities of the compacted bentonite were 1.4 Ms/㎥ to 1.8 Mg/㎥. The diffusion coefficients in the compacted bentonite were measured under an oxidizing condition. The values were $1.7{\times}10^{-10}$m^2$/s to 3.4{\times}10^{-10}$m^2$/s for electrically neutral tritium (H-3), 8.6{\times}10^{-14}$m^2$/s to 1.3{\times}10^{-12}$m^2$/s for cations (Cs, Sr, Ni), 1.2{\times}10^{-11}$m^2$/s to 9.5{\times}10^{-11}$m^2$/s for anions (I, Tc), and 3.0{\times}10^{-14} $m^2$/s to 1.8{\times}10^{-13}$m^2$/s $for actinides (U, Am), when tile dry densities were in the range of 1.2 Mg/㎥ to 1.8 Mg/㎥. The obtained results will be used in assessing the barrier properties of Kyungju bentonite as a buffer material of a repository in Korea.n Korea.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.46 no.2
• /
• pp.179-184
• /
• 2020

Elasticity and softness of the skin depend on the level of moisture present in the stratum corneum, which is known to be affected by various environmental changes, such as cold and hot winds and dry environments. However, not many studies have been conducted on changes in skin moisture and the degree of recovery due to individual skin differences. In the present study, we aimed to investigate the effect of warm air heating on skin hydration levels and develop moisturizing formulas to improve lowered skin hydration levels. In order to deliver warm air heating condition, heating dryer (40 ℃, 6 m/s, 30 cm apart from forearm) was applied into inner forearm of healthy subjects (male: 10, female: 39, age: 25 - 63) Among 49 subjects, 26 subjects showed significantly lowered skin hydration levels until 30 min after warm air heating exposure (lowered group). In addition, moisturizing cream with high water holding capacity was applied to forearm of 10 subjects in lowered group for 3 weeks and skin hydration levels after warm air heating were significantly improved at the levels of before application of warm air heating. From this study, we found out that there is a skin type that skin hydration levels are significantly decreased under warm air heating condition (dehydrated skin) and this dehydrated skin can be improved by moisturizing formulas with high water holding capacity.

• Journal of Life Science
• /
• v.24 no.6
• /
• pp.618-625
• /
• 2014

Rice flour is used in many food products. However, dough made from rice lacks extensibility and elasticity, making it less suitable than wheat for many food products such as bread and noodles. The high-molecular weight glutenin subunits (HMW-GS) of wheat play a crucial role in determining the processing properties of the wheat grain. This paper describes the development of marker-free transgenic rice plants expressing a wheat Glu-Dy10 gene encoding the HMG-GS from the Korean wheat cultivar 'Jokyeong' using Agrobacterium-mediated co-transformation. Two expression cassettes, consisting of separate DNA fragments containing Glu-1Dy10 and hygromycin phosphotransferase II (HPTII) resistance genes, were introduced separately into Agrobacterium tumefaciens EHA105 for co-infection. Each EHA105 strain harboring Glu-1Dy10 or HPTII was infected into rice calli at a 3: 1 ratio of Glu-1Bx7 and HPTII. Among 290 hygromycin-resistant $T_0$ plants, we obtained 29 transgenic lines with both the Glu-1Dy10 and HPTII genes inserted into the rice genome. We reconfirmed the integration of the Glu-1Dy10 gene into the rice genome by Southern blot analysis. Transcripts and proteins of the Glu-1Dy10 in transgenic rice seeds were examined by semi-quantitative RT-PCR and Western blot analysis. The marker-free plants containing only the Glu-1Dy10 gene were successfully screened in the $T_1$ generation.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1379-1385
• /
• 2007

In domestic transitional zone design, there is regulation to prevent generation of irregular substructure behaviors that negatively influence in prevention of plasticity settlement on approach section and contact section as well as relieve overall track rigidity by reducing sectional foundation and track stiffness difference, but design guideline that considers dynamic behavior of transitional track in actual service line is very insignificant. Therefore in this study, characteristics of transitional track dynamic behaviors by substructure stiffness are researched and measured dynamic response of transitional track by substructure stiffness in order to prove correlation between substructure and track and calculate elasticity(stiffness) and track load of transitional track by using measurement and formula to provide basic information for developing design guideline considering dynamic behavior of service line transitional track.

• Journal of Korean Society of Forest Science
• /
• v.96 no.4
• /
• pp.455-461
• /
• 2007

This research was processed on morphological and physical characteristics of 'Yongdong' cultivar nuts. (1)Morphological properties of 'Yongdong' cultivar nuts were significantly different from the control, native species, in respect of all properties. (2) 'Yongdong' cultivar nuts showed higher figures than the native species on 9 items of morphological properties (kernel weight, size, length and width of pad on suture and etc.), whereas other 6 items (height of pad on suture, thickness of shell and septem, fragment numbers of isolated kernel, roundness index, and etc.) showed lower figures than those of the control. (3) In physical properties of the nut shells, 'Yongdong' cultivar was superior to the control at all items with the exception of compressive prove distance. Accordingly, it was also verified as effective cultivar of shelled walnut with suture line direction applied the minimum strength. (4) 'Yongdong' cultivar, 21.9 kg, was approximately twice lower than the control, 42.6 kg, on maximum compressive weight. It was demonstrated that the 'Yongdong' cultivar characterized by easily crushing shell by small strength was great in cracking properties. (5) On the study of yield strength, the native species being twice higher than 'Yongdong' cultivar showed the properties of the small elasticity and the shell hardness. While, the suture line of 'Yongdong' cultivar having the lowest yield strength 15.6 kg and 16.0 kg was identified the shell crushed easily. (6) The movement distance of the compressive prove of 'Yongdong' cultivar, 4.2 mm, was longer than that of the control, 2.7 mm. Subsequently, it means that the amount of loss possibly occurring to distribution process was not great, whereby productive value was high. (7) The compressive strength of the suture line of 'Yongdong' cultivar, $9.1kg/cm^2$, was much lower than total average of that $12.4kg/cm^2$. It was also statistically different with other properties. (8)The hardness examination by the compressive position revealed that the suture line of 'Yongdong' cultivar, $149.8kg/cm^2$, was lowest in contrast with the control, $300.9kg/cm^2$.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.6-13
• /
• 2018

Utilizing the heat of cooling water discharge of coal-fired power plant, pipeline investment costs for businesses that supply heat to agricultural facilities near power plants increase in proportion to installation distance. On one hand, the distance from the power plant is a factor that brings difficulties to secure economic efficiency. On the other, if the installation distance is short, there is a problem of securing the heating demands, facility houses, which causes economical efficiency to suffer. In this study, the economic efficiency of 1km length of standard heat pipeline was evaluated. The sensitivity of the heat pipe to the new length variation was analyzed at the level of government subsidy, amount of heating demand and the incremental rate of pipeline with additional government subsidy. As a result of the analysis, it was estimated that NPV 131 million won and IRR 15.73%. The sensitivity analysis showed that NPV was negative when the length of heat pipe facility exceeded 2.6 km. If the government supports 50% of the initial investment, the efficiency is secured within the estimated length of 5.3 km, and if it supports 80%, the length increases within 11.4 km. If the heat demand is reduced to less than 62% at the new length of the standard heat pipe, it is expected economic efficiency is not obtained. If the ratio of government subsidies to initial investment increases, the elasticity of the new bloc will increase, and the fixed investment, which is the cost of capital investment for one unit of heating demand, will decrease. This would result in a reduction in the cost of production per unit, and it would be possible to supply heat at a cheaper price level to the facility farming. Government subsidies will result in the increased economic availability of hot plumbing facilities and additional efficiencies due to increased demand. The greater government subsidies to initial investment, the less farms cost due to the decrease in the price per unit. The results of the study are significant in terms of the economic evaluation of the effectiveness of the government subsidy for the thermal power plant heat utilization project. The implication can be applied to any related pilot to come.

• Korean journal of food and cookery science
• /
• v.23 no.4 s.100
• /
• pp.461-468
• /
• 2007

The quality characteristics of bread made from domestic Korean wheat flour that contained different amounts of cactus Chounnyuncho (Opuntia humifusa) powder were investigated. The water absorption and peak time, as determined by a farinograph, increased with increasing amounts of cactus powder, while stability, elasticity, and weakness decreased (p<0.05). RVA(Rapid Visco Analyzer) analysis showed that wheat flour retrogradation was retarded by increasing cactus powder content (p<0.05). The fermentation time of the bread increased with increasing cactus powder content, while the fermented volume and baking loss decreased (p<0.05). According to the sensory test, the most preferred bread contained 3% cactus powder (p0.05).

• KDI Journal of Economic Policy
• /
• v.12 no.3
• /
• pp.27-45
• /
• 1990

Two opposing views prevail regarding the economic impact of rural out-migration on the rural areas of origin. The optimistic neoclassical view argues that rapid rural out-migration is not detrimental to the income and welfare of the rural areas of origin, whereas Lipton (1980) argues the opposite. We developed our own alternative model for rural to urban migration, appropriate for rapidly developing economies such as Korea's. This model, which adopts international trade theories of nontraded goods and Dutch Disease to rural to urban migration issues, argues that rural to urban migration is caused mainly by two factors: first, the unprofitability of farming, and second, the decrease in demand for rural nontraded goods and the increase in demand for urban nontraded goods. The unprofitability of farming is caused by the increase in rural wages, which is induced by increasing urban wages in booming urban manufacturing sectors, and by the fact that the cost increases in farming cannot be shifted to consumers, because farm prices are fixed worldwide and because the income demand elasticity for farm products is very low. The demand for nontraded goods decreases in rural and increases in urban areas because population density and income in urban areas increase sharply, while those in rural areas decrease sharply, due to rapid rural to urban migration. Given that the market structure for nontraded goods-namely, service sectors including educational and health facilities-is mostly in monopolistically competitive, and that the demand for nontraded goods comes only from local sources, the urban service sector enjoys economies of scale, and can thus offer services at cheaper prices and in greater variety, whereas the rural service sector cannot enjoy the advantages offered by scale economies. Our view concerning the economic impact of rural to urban migration on rural areas of origin agrees with Lipton's pessimistic view that rural out-migration is detrimental to the income and welfare of rural areas. However, our reasons for the reduction of rural income are different from those in Lipton's model. Lipton argued that rural income and welfare deteriorate mainly because of a shortage of human capital, younger workers and talent resulting from selective rural out-migration. Instead, we believe that rural income declines, first, because a rapid rural-urban migration creates a further shortage of farm labor supplies and increases rural wages, and thus reduces further the profitability of farming and, second, because a rapid rural-urban migration causes a further decline of the rural service sectors. Empirical tests of our major hypotheses using Korean census data from 1966, 1970, 1975, 1980 and 1985 support our own model much more than the neoclassical or Lipton's models. A kun (county) with a large out-migration had a smaller proportion of younger working aged people in the population, and a smaller proportion of highly educated workers. But the productivity of farm workers, measured in terms of fall crops (rice) purchased by the government per farmer or per hectare of irrigated land, did not decline despite the loss of these youths and of human capital. The kun having had a large out-migration had a larger proportion of the population in the farm sector and a smaller proportion in the service sector. The kun having had a large out-migration also had a lower income measured in terms of the proportion of households receiving welfare payments or the amount of provincial taxes paid per household. The lower incomes of these kuns might explain why the kuns that experienced a large out-migration had difficulty in mechanizing farming. Our policy suggestions based on the tests of the currently prevailing hypotheses are as follows: 1) The main cause of farming difficulties is not a lack of human capital, but the in­crease in production costs due to rural wage increases combined with depressed farm output prices. Therefore, a more effective way of helping farm economies is by increasing farm output prices. However, we are not sure whether an increase in farm output prices is desirable in terms of efficiency. 2) It might be worthwhile to attempt to increase the size of farmland holdings per farm household so that the mechanization of farming can be achieved more easily. 3) A kun with large out-migration suffers a deterioration in income and welfare. Therefore, the government should provide a form of subsidization similar to the adjustment assistance provided for international trade. This assistance should not be related to the level of farm output. Otherwise, there is a possibility that we might encourage farm production which would not be profitable in the absence of subsidies. 4) Government intervention in agricultural research and its dissemination, and large-scale social overhead projects in rural areas, carried out by the Korean government, might be desirable from both efficiency and equity points of view. Government interventions in research are justified because of the problems associated with the appropriation of knowledge, and government actions on large-scale projects are justified because they required collective action.

• Korean Journal of Agricultural Science
• /
• v.8 no.1
• /
• pp.97-107
• /
• 1981

This study was carried out in order to provide the basic data necessary to develop the effective and desirable cooking method on large scale for investigating the physical characteristics of cooked rices and studying optimum cooking conditions by pressure in kettle cooking rices. Milyang-15, local Japonica type and Milyang-23, high yielding Indica type major varieties cultivated in Korea were used as cooking sample after polishing 70% and 90% respectively, and the results obtained are summarized as follows. 1. The average moisture content of cooked rice by open kettle and pressure kettle method in typical households were 65.17% and 64.52%, respectively. 2. In water absorption capacity of rice grain Milyang-23 was 4.5% higher than Milyang-15, and maximum water content after absorption in Milyang-23 was 29.14%. 3. The expansion volume of cooked rice was changed proportionally by water absorption, heating temperature and time, and maximum expansion volume of cooked rice was 3.2 times greater than rice grain. 4. The gelatinization degree of cooked rice intensively concerning in hardness of rice grain was increased as water-to-rice ratio, heating temperature and time increased, and it was 0.44 in Milyang-23 and 0.64 in Milyang-15 under the optimum cooking conditions as 160% water-to-rice ratio, $0.2kg/cm^2$ cooking pressure and 25 minutes cooking time. 5. The hardness of cooked rice was decreased as water-to-rice ratio, heating temperature and time increased, and it showed 2.35kg/wt in 90% polished Milyang-23 and 2.0kg/wt in 90 polished Milyang-15 under optimum cooking conditions. For maintaining the same level of hardness of cooking rice Milyang-23 required 25% much more water than Milyang-15. 6. The elasticity of cooked rice was changed proportionally by water-to-rice ratio, heating temperature and time, and it appeared 19.2mm and 15.7mm in 90% polished Milyang-15 and Milyang-23 respectively. 7. The gumminess of cooked rice was decreased as water-to-rice ratio, heating temperature and time increased, and it showed 60 and 73 in 90% polished Milyang-23 and Milyang-15, respectively. 8. The optimum cooking time on differerent pressure in kettle took 25 minutes at $0.2kg/cm^2$, 20 minutes at $0.4kg/cm^2$, 15 minutes at $0.6kg/cm^2$, and 10 minutes at $0.8kg/cm^2$.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.4
• /
• pp.3-57
• /
• 1985

This research was conducted to examine the feasibility of developing fire retardant particleboard and complyboard. Particleboard were manufactured using meranti particle(Shorea spp.)made with Pallmann chipper, and complyboard meranti particle and apitong veneer (Dipterocarpus spp.). Particles were passed through 4mm (6 mesh) and retained on 1mm (25 mesh). Urea formaldehyde resin was added 10 percent on ovendry weight of particle. Face veneer for complyboard was 0.9, 1.6 and 2.3mm in thickness and spread with 36 g/(30.48 cm)$^2$ glue on one side. Veneers were soaked with 10 percent solution of five fire retardant chemicals (diammonium phosphate, ammonium sulfate, monoammonium phosphate, Pyresote and Minalith), and particles with 5, 10, 15 and 20 percent solution of five chemicals. Particleboard and complyboard were evaluated on physical and mechanical properties, and fire retardancy. The results obtained were summarized as follows. 1. Among five fire retardant chemicals treated to particleboard and complyboard, the retention of ammonium sulfate in 5 percent solution showed the lowest as 1.39 kg/(30.48 cm)$^3$ exceeding the minimum retention of 1.125 kg/(30.48 cm)$^3$ recommended by Forest Products Laboratory and Koch. 2. Particleboard and complyboard treated with diammonium phosphate showed higher modulus of rupture (MOR), modulus of elasticity (MOE), internal bond strength and screw holding power than those with the other chemicals. 3. MOR and MOE of complyboard treated with fire retardant chemicals were greater than those of fire retardant particleboard. 4. Thickness swelling of fire retardant complyboard was lower than that of fire retardant particleboard. 5. The moisture content of the boards treated with Pyresote and Minalith increased and with monoammonium phosphate reduced. 6. Fire retardant particleboard showed no ignition, and fire retardant complyboard started ignition, but time required to ignite was prolonged comparing the controlboard. Complyboard with only shell veneer treated showed ignition and lingering flame, but lingering flame time was shorter than controlboard. Complyboard with treated both core and veneer showed ignition but not lingering flame. 7. Flame length, carbonized area and weight loss were smaller than controlboard but had no significant difference among chemicals treated. 8. Temperature of unexposed surface of fire retardant particleboard was lowered with the increasing concentration of five chemicals. 9. Temperature of unexposed surface of fire retardant particleboard was lowered with the highest in Pyresote and the lowest in Minalith. 10. Temperature of unexposed surface of fire retardant complyboard was lower than that of controlboard.