• Korean Journal of Remote Sensing
• /
• v.36 no.5_1
• /
• pp.679-692
• /
• 2020

We coupled a CFD model to the WRF-Chem model (WRF-CFD model) and investigated the characteristics of flows and carbon monoxide (CO) distributions in a building-congested district. We validated the simulated results against the measured wind speeds, wind directions, and CO concentrations. The WRF-Chem model simulated the winds from southwesterly to southeasterly, overestimating the measured wind speeds. The statistical validation showed that the WRF-CFD model simulated the measured wind speeds more realistically than the WRF-Chem model. The WRF-Chem model significantly underestimated the measured CO concentrations, and the WRF-CFD model improved the CO concentration prediction. Based on the statistical validation results, the WRF-CFD model improved the performance in predicting the CO concentrations by taking complicatedly distributed buildings and mobiles sources of CO into account. At 04 KST on May 22, there was a downdraft around the AQMS, and airflow with a relatively low CO concentration was advected from the upper layer. Resultantly, the CO concentration was lower at the AQMS than the surrounding area. At 15 KST on May 22, there was an updraft around the AQMS. This resulted in a slightly higher CO concentration than the surroundings. The WRF-CFD model transported CO emitted from the mobile sources to the AQMS measurement altitude, well reproducing the measured CO concentration. At 18 KST on May 22, the WRF-CFD model simulated high CO concentrations because of high CO emission, broad updraft area, and an increase in turbulent diffusion cause by wind-shear increase near the ground.

• Journal of computational fluids engineering
• /
• v.9 no.1
• /
• pp.41-47
• /
• 2004

A successful store separation analysis tool, MSAP(Multi-body Separation Analysis Program) has been applied to F/A-18C/JDAM CFD Challenge Ⅱ. The challenge was devised to challenge CFD community to use CFD methodologies to predict and match the trajectory of a JDAM MK-84 separating from F/A-l8C. Trajectory simulations for two flight conditions were performed. Comparison between computed and measured flight trajectories for both conditions shows a good agreement.

• 한국전산유체공학회:학술대회논문집
• /
• 2001.10a
• /
• pp.37-43
• /
• 2001

The methods of atmospheric boundary layer generation in test section were reviewed. To utilize conventional aerodynamic wind tunnels as atmospheric wind tunnels, boundary layer growth should be accelerated. To achieve this, improvement of boundary layer generation devices is required and it might be done by CFD. In this respect, CFD application cases in boundary generation devices were reviewed and potential areas were considered. Some cases are tried by Fluent 5 code.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.105-109
• /
• 2004

CFD simulation for Smart-UAV(TR-E2Sl) is performed to analyze its aerodynamic characteristics. Base geometry and several cases, decided by control surfaces being deflected, are simulated. To obtain the better lift characteristics, the elevator should be deflected between 10o and 20o with the incidence angle of the wing 1o.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.08a
• /
• pp.89-94
• /
• 2003

A successful store separation analysis tool, MSAP(Multi-body Separation Analysis Program) has been applied to F/A-18C/JDAM CFD Challenge II. The challenge was devised to challenge CFD community to use CFD methodologies to predict and match the trajectory of a JDAM MK-84 separating from F/A-l8C. Trajectory simulations for two flight conditions were performed. Comparison between computed and measured flight trajectories for both conditions shows a good agreement.

• Journal of Korea Society of Industrial Information Systems
• /
• v.29 no.1
• /
• pp.107-116
• /
• 2024

Copper Filter Dryer (CFD) are responsible for removing impurities from the circulation of refrigerant in refrigeration and cooling systems to maintain clean refrigerant, and defects in CFD can lead to product defects such as leakage and reduced lifespan in refrigeration and cooling systems, making quality assurance essential. In the quality inspection stage, human inspection and defect judgment methods are traditionally used, but these methods are subjective and inaccurate. In this paper, YOLOv7 object detection algorithm was used to detect defects occurring during the CFD Shaft pipe and welding process to replace the existing quality inspection, and the detection performance of F1-Score 0.954 and 0.895 was confirmed. In addition, the cause of defects occurring during the welding process was analyzed by analyzing the sensor data corresponding to the Timestamp of the defect image. This paper proposes a method for manufacturing quality assurance and improvement by detecting defects that occur during CFD process and analyzing their causes.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.1
• /
• pp.23-33
• /
• 2019

Unmanned Surface Vehicle (USV) is being developed to do maritime survey and maritime surveillance at Korea Research Institute of Ships & Ocean engineering (KRISO). The goal is that USV should be operated at the maximum speed of 45 knots and it should be operated at sea state 4. Therefore the planing hull of USV should be excellent in resistance performance and manoeuvring performance. It is needed to check its performance using Experimental Fluid Dynamics (EFD), Computational Fluid Dynamics (CFD) or analytic method before designing the hull. In this study, resistance performance was analyzed by EFD and CFD. EFD with heave and pitch was performed at high speed towing system in Seoul National University. CFD was performed using SNUFOAM based on openFOAM with dynamic mesh to calculate running attitudes. The results of CFD were compared with EFD results. The results of CFD were resistance, running attitudes and wave height. The flow distribution and pressure distribution were also analyzed. The results of numerical resistance was under estimated than EFD. Even though the results of CFD have a slight limitation, it can be successfully used to estimate the resistance performance of planing hull. In addition it can be used as a supplement for EFD results.

• Journal of Aerospace System Engineering
• /
• v.18 no.2
• /
• pp.40-46
• /
• 2024

This study suggests a method to enhance drone flight path planning and safety evaluation in urban areas using Computational Fluid Dynamics (CFD). As the use of drones in urban environments has been growing rapidly, there is a lack of established methods for path planning and safety evaluation, which leads to a risky approach relying on experimental methods. Therefore, this research takes into account the intricate 3D fluid dynamics between drones and buildings by employing CFD to quantitatively plan flight paths and evaluate their safety. To accomplish this, the study focuses on Gimcheon Innovation City as the target area and collects relevant terrain and building data, and selects prospective flight routes. CFD analysis is then carried out to gather essential data for flight simulations and safety assessment. The safety assessments are conducted based on environmental fluid dynamics when the drone operates along the proposed flight paths

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.1
• /
• pp.107-112
• /
• 2009

This study was conducted for verification and systematization of estimation method about the headloss using CFD(Computational Fluid Dynamics). Head loss which happens between the inlet and outlet of in-line mixer can be a major factor for the design and construction. Also, this Case studies about the sensitivity related to the velocity in the piping system. As result, program's default calculation function was used to get each side's total pressure and the differential of each total pressure could be defined as head loss from in-line mixer. In the case of adopting pipe surface friction factor and geometry loss, Calculation residual can be much more reduced. It was found that residual of value between CFD method and field test ranged about 3 through 18 precent.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.517-523
• /
• 2010

Recently, the rapid evolution of computational fluid dynamics (CFD) has enabled its key role in industries and predictive sciences. From diverse research disciplines, however, are there strong needs for integrated analytical tools for multi-phenomena beyond simple flow simulation. Based on the concurrent simulation of multi-dynamics, multi-phenomena beyond simple flow simulation. Based on the concurrent simulation of multi-dynamics, multi-physics and multi-scale phenomena, the multi-phenomena CFD technology enables us to perform the flow simulation for integrated and complex systems. From the multi-phenomena CFD analysis, the high-precision analytical and predictive capacity can enhance the fast development of industrial technologies. It is also expected to further enhance the applicability of the simulation technique to medical and bio technology, new and renewable energy, nanotechnology, and scientific computing, among others.