• Journal of the Korean Society of Marine Environment & Safety
• /
• v.15 no.1
• /
• pp.49-55
• /
• 2009

Typhoons are usually influencing at least 3 or 4 times per year in Korean peninsula and they accompanied with strong winds and heavy rains and then brought tremendous loss of properties and lives. Especially typhoon "MAEMI" resulted in a lot of marine accidents of vessels such as sinking, stranding, collision etc. at anchoring or on berthing in pier. If the typhoon comes up to expected area influencing the incidents, the vessel tries to escape from the route of typhoon or anchor in sheltering anchorage. However, consideration of the anchoring or judgement of ship's safety against strong winds is decided only by the experience of operators without detail evaluation of the safety. Therefore, this paper evaluated the safety of T.S. HANBADA by comparing the external forces with the holding powers. Furthermore, based on this evaluation, the anchoring manual was produced for the maximum endurable wind velocity, the general precautions and the actions taken on the ship with steps.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.2
• /
• pp.8-16
• /
• 2015

Prestressed concrete (PSC) is a method in which prestressed tendon is placed inside and/or outside the reinforced concrete member and the compressive force applied to the concrete in advance to enhance the engineering properties of concrete member which is weak under tension. In this paper we suggested the precast PSC girder assembled with segments of portable size and weight at the factory. The segments of precast PSC girder will be delivered and assembled as a unit of PSC girder at the site. Consequently, we suggested new-type of precast segmented PSC girder with different shapes of segment cross-section (i.e., I-shape, Box-shape). To mitigate the problems associated with the field splice between the segments of precast PSC girder anchor system is attached near the neutral axis of the girder and relatively uniform compression throughout the girder cross-section is applied. Prior to the experimental investigation, analytical investigation on the structural behavior of precast PSC girder was performed and the serviceability (deflection) and safety (strength) of the girder were confirmed. In addition, 4-point bending test on the girder was conducted to investigate the structural performance under bending. From the experimental investigation, it was found that the precast PSC girder spliced with 3 and 5 segments has sufficient in serviceability and safety conditions and it was also observed that the point where the segments spliced has no defects and the girder behaves as a unit.

• Journal of Navigation and Port Research
• /
• v.31 no.6
• /
• pp.485-490
• /
• 2007

The purpose in having a control rod on a buoy system is to control the motion of it. The system may be composed entirely of a single circular cylinder and a long mooring anchor cable. A control rod has one function to perform in meeting its purpose, and that is to develop a control force in consequence of its orientation and movement relative to the water. The forces and moments generated as a result of the effects of mutual interference. then determine the stability characteristics of the body. In this paper, the study of control-rod-attached buoy's 2-dimensional section was accomplished. model tests and numerical simulations had been carried out with different diameters of control rods. and varying the Reynolds number $Re=5,000{\sim}25,000$ based on the cylinder diameter(D=50mm) to predict the performance of the body and the 2 frame particle tracking method Iud been used to obtain the velocity distribution in the flow field. 50mm circular cylinder Iud been used during the whole experiments and measured results had been compared with each other.

• The korean journal of orthodontics
• /
• v.48 no.5
• /
• pp.304-315
• /
• 2018

Objective: The purpose of this study was to analyze initial displacement and stress distribution of the maxillofacial complex during dentoskeletal maxillary protraction with various appliance designs placed on the palatal region by using three-dimensional finite element analysis. Methods: Six models of maxillary protraction were developed: conventional facemask (Type A), facemask with dentoskeletal hybrid anchorage (Type B), facemask with a palatal plate (Type C), intraoral traction using a Class III palatal plate (Type D), facemask with a palatal plate combined with rapid maxillary expansion (RME; Type E), and Class III palatal plate intraoral traction with RME (Type F). In Types A, B, C, and D, maxillary protraction alone was performed, whereas in Types E and F, transverse expansion was performed simultaneously with maxillary protraction. Results: Type C displayed the greatest amount of anterior dentoskeletal displacement in the sagittal plane. Types A and B resulted in similar amounts of anterior displacement of all the maxillofacial landmarks. Type D showed little movement, but Type E with expansion and the palatal plate displayed a larger range of movement of the maxillofacial landmarks in all directions. Conclusions: The palatal plate served as an effective skeletal anchor for use with the facemask in maxillary protraction. In contrast, the intraoral use of Class III palatal plates showed minimal skeletal and dental effects in maxillary protraction. In addition, palatal expansion with the protraction force showed minimal effect on the forward movement of the maxillary complex.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.19-30
• /
• 2000

The major design parameters of the anchored sheet-pile wall include the determination of required penetration depth, the force acting on the anchor, and the maximum bending moment in the piling. Blum solved the fixed earth supported wall using the equivalent beam method, assuming that the wall can be separated into upper and lower parts of the point of contraflexure. Design charts help designer by simplifying the design procedure. But they have some difficulties under some Geotechnical and geometrical conditions. For example, the conventional design charts can compute design parameters only when the ground water table exists above the dredge line. In this paper, the design charts which can be used for the ground water table existing under the dredge line are presented. And simplified formulae are developed by regression analysis. It is found that simplified formulae are not only very useful for the practice of design but also they can evaluate the result of numerical methods or design charts.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6B
• /
• pp.544-550
• /
• 2006

Next-generation wireless/mobile networks are envisioned to have an IP-based infrastructure. One of the research challenges for next-generation all IP-based networks is the design of intelligent mobility management technologies that have a seamless mobility and minimal signaling overhead. Recently, HMIPv6 was proposed by the IETF for efficient mobility management. HMIPv6 reduces the amount of signaling and improves the performance of MIPv6 in terms of handover latency. However the MAP can be a single point of performance bottleneck when there are a lot of local movements. HMIPv6 can cause signaling overhead due to the unnecessary location update of idle mobile nodes. Therefore, in this paper, we propose the dynamic paging Mobile IPv6 that reduces the signaling cost of the unnecessary location updates using IP paging and organizes dynamically optimal MAP area according to user's mobility and traffic. We show performance results that are obtained from the average total location update cost and packet delivery cost.

• Structural Engineering and Mechanics
• /
• v.57 no.3
• /
• pp.507-528
• /
• 2016

Reduced beam section (RBS) moment resisting connections are among the most economical and practical rigid steel connections developed in the aftermath of the 1994 Northridge and the 1995 Kobe earthquakes. Although the performance of RBS connection has been widely studied, this connection has not been subject to in the skewed conditions. In this study, the seismic performance of dogbone connection was investigated at different angles. The Commercial ABAQUS software was used to simulate the samples. The numerical results are first compared with experimental results to verify the accuracy. Nonlinear static analysis with von Mises yield criterion materials and the finite elements method were used to analyze the behavior of the samples The selected Hardening Strain of materials at cyclic loading and monotonic loading were kinematics and isotropic respectively The results show that in addition to reverse twisting of columns, change in beam angle relative to the central axis of the column has little impact on hysteresis response of samples. Any increase in the angle, leads to increased non-elastic resistance. As for Weak panel zone, with increase of the angle between the beam and the column, the initial submission will take place at a later time and at a larger rotation angle in the panel zone and this represents reduced amount of perpendicular force exerted on the column flange. In balanced and strong panel zones, with increase in the angle between the beam and the central axis of the column, the reduced beam section (RBS), reaches the failure limit faster and at a lower rotation angle. In connection of skewed beam, balanced panel zone, due to its good performance in disposition of plasticity process away from connection points and high energy absorption, is the best choice for panel zone. The ratio of maximum moment developed on the column was found to be within 0.84 to 1 plastic anchor point, which shows prevention of brittle fracture in connections.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.4B
• /
• pp.647-658
• /
• 2010

Many localization schemes estimate the locations of radio nodes based on the physical locations of anchors and the connectivity from the anchors. Since they only consider the knowledge of the anchors without else other nodes, they are likely to have enormous error in location estimate unless the range information from the anchors is accurate or there are sufficiently many anchors. In this paper, we propose a novel localization algorithm with the location knowledge of anchors and even one-hop neighbors to localize unknown nodes in the uniform distance from all the one-hop neighbors without the range information. The node in the uniform distance to its all neighbors reduces the location error relative to the neighbors. It further alleviates the location error between its actual and estimated locations. We evaluate our algorithm through extensive simulations under a variety of node densities and anchor placement methods.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.5
• /
• pp.26-34
• /
• 2016

The failure modes of steel column-base plate connection arranged on the basis of AISC Design Guide-#1 and -#10 are base plate tension and compression side flexural yielding, yielding, pull-out and shear failure of anchor rod, concrete crushing in concrete footing and steel column yielding. The bending moment capacity and failure mode in this connection are predicted using limit-state function and we compare these results and test result. In the case that thickness of base plate is relatively thick, bending moment capacity and failure mode in steel column-base plate connection accurately predicted. But in the case that thickness of base plate is relatively thin and axial force do not exist, prediction of failure mode in this connection is somewhat inaccurate.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.05a
• /
• pp.169-174
• /
• 2007

The purpose in having a control rod an a buoy system is to control the motion of it. The system may be composed entirely af a single circular cylinder finder and a lang mooring anchor cable. A control rod has one function to perform in meeting its purpose, and that is to develop a control force in consequence of its orientation and movement relative to the water. The forces and moments generated as a result of the effects of mutual interference, then determine the stability characteristics of the body. In this paper, the study of control-rod-attached buoy's 2-dimensional section was accomplished. model tests and numerical simulations had been carried out with different diameters of control rods. and varying the Reynolds number $Re=5,000{\sim}25,000$ based an the cylinder diameter(D=50mm) to. predict the performance af the body and the 2 frame particle tracking method had been used to obtain the velocity distribution in the flaw field 50mm circular cylinder had been used during the whale experiments and measured results had been compared with each other.