• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2002년도 춘계 학술발표회 논문집
• /
• pp.143-150
• /
• 2002

This paper presents the application of continuous wavelet transform for determination of dynamic parameters of continuous beam subjected to moving load. Morlet wavelet is used as mother wavelet in wavelet transform. Dynamic parameters are estimated from the magnitudes and arguments of the wavelet coefficients obtained by wavelet transforming the response time histories of joints on the beam. This study shows that the estimated parameters such as natural frequencies, dmping ratios and mode shapes are to be well-compared with those of the finite element analysis.

• Tribology and Lubricants
• /
• 제18권3호
• /
• pp.181-186
• /
• 2002

A numerical analysis is undertaken to show the influence of bearing design parameters on the load capacity of air lubricated spiral grooved thrust bearing. The governing equation derived from the mass balance is solved by the finite difference method. Optimal values for various design parameters are obtained to maximize the load capacity. The design parameters are the groove angle, the groove width ratio, the groove height ratio, and the seal ratio.

• 한국농공학회지
• /
• 제40권1호
• /
• pp.57-67
• /
• 1998

A stochastic weather generator which simulate daily precipitation, maximum and minimum daily temperature, relative humidity was developed. The model parameters were estimated using stochastic characteristics analysis of historical data of 71 weather stations. Spatial variations of the parameters for the country were also analyzed. Model parameters of ungauged Sites were determined from parameters of adjacent weather stations using inverse distance method. The model was verified on Suwon and Ulsan weather stations and showed good agreement between simulated and observed data.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.257-262
• /
• 2001

A numerical analysis is undertaken to show tile influence of bearing design parameters on tile load capacity of air lubricated spiral grooved thrust bearing. The governing equation derived from the mass balance is solved by the finite difference method. Optimal values for various design parameters are obtained to maximize the load capacity. The design parameters are the groove angle, the groove width ratio, the groove height ratio, arid the seal ratio.

• 대한인간공학회지
• /
• 제10권2호
• /
• pp.15-22
• /
• 1991

Gait analysis techniques are widely used in Europe and the United States to investigate the loosening problems of total joint implantation and to improve the technologies in designing prosthetic devices. In Korea, however, the gait data are rarely found. Recently, as the standards of living become improved, the number of lower extremity operation patients increase rapidly. Therefore, a study on the gait characteristic parameters for Koreans is of great importance. In this study, time-distance gait parameters and ground reaction fore are analyzed using a FOANAS system developed by Pohang Institute of Science and technology (POSTECH). Gait parameters of Korean normal adults were preceded and comparisons were made for the distinction of sex and age.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.96-99
• /
• 2008

When the design modification is occurred, at present, design process based on 2-D spend more time and effort than that based on 3-D to modify related structural details. To improve and develop these processes, therefore, the design possibility of civil structures based on virtual model of 3-D must be investigated. We designed reinforced concrete pier of 3-D model, containing parameters. The parameters was defined as structural details like area of the section, reinforcement specification for design modification and structural analysis. In this paper, we researched about the processes modeling of reinforced concrete bridge pier based on parameters, the extracting data from the virtual model of 3-D, and the reflection of data to virtual model throughout structural analysis.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.235-243
• /
• 1998

For motor operation at low speeds and loads, torque pulsation by the cogging torque is often a source of vibration and control difficulty. In this paper, the magnetic field of a motor is calculated by finite element method. The periodic cogging torque is determined using Maxwell stress method and time stepping method, and then decomposed using fourier series expansion, The purpose of this paper is to characterize design parameters on the cogging torque and to design a permanent magnet motor with a cogging torque less vulnerable to vibration, without sacrificing the motor performance. The design parameters include stator slot width, permanent magnet slot width, airgap length and magnetization direction. A new design with a less populated frequency spectrum of the cogging torque is proposed after characterizing individual effect of design parameters. Magnet pole edge shaping, by gradually increasing the cogging torque with reduced higher harmonics.

• The Journal of Korean Physical Therapy
• /
• 제17권4호
• /
• pp.569-574
• /
• 2005

The purposes of this study were to present the basic reference data of age and specipic gait parameters for Parkinson's disease patients. The basic gait parameters were extracted from 20 patients of parkinson's disease and 20 healthy control subjects using VICON 512 Motion Analyzer. The temporal gait parameters and kinematic parameters is data of Parkinson' s Disease Patients. The results were as follows: (1) In patients' group, cadence, walking velocity were less than control group (p<.05). (2) In patients' group, maximum flexion of hip, maximum adduction of hip and maximum flexion of the knee were less than control group (p<.05). (3) In patients' group, maximum varus of the knee were more than control group (p<.05).

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.835-840
• /
• 2002

The purpose of this study is to analyze the reinforcement effect of the RC compressive member confined with carbon fiber sheets and to suggest better transverse confinement coefficient(k$_1$) than one's in the existing analysis equations. Showing amounts of CPS in terms of ratio of transverse reinforcement to cross-section, it comes to be possible to calculate the objective and quantitative reinforcement amounts and to estimate the overlapping length of CFS that can influence on all its confinement effect. The previous parameters were compared using the existing experimental test data, then analyzed for the merits and demerits of existing parameters through the coefficient of correlation(R). The proposed parameters were derived in such a way that established parameters and their combination were obtained from the analytical study and then determined by regression analysis using the previous test data.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.244-246
• /
• 2006

In this study, we search some parameters well-related to floating-sinking pulse by statistical analysis, because these pulses are frequently used in clinic. Pulse signals were acquired by 3D pulse analyzer and 30 subjects consist of 15 people diagnosed as floating pulse and 15 people diagnosed as sinking pulse by oriental doctors who have over 5 years clinical experience. Then, we made a representative beat template for each subject and, through a peak detection algorithm, we calculated several pulse parameters. To find the parameters related to floating-sinking pulse, we performed statistical testing with 17 parameters through the independence sampling, t-test. As a result, there is the biggest difference between pressure, the maximum pulse pressure, diastolic area(Ad) and float-sink data. (p < .05).