• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.3
• /
• pp.229-236
• /
• 2017

In this study, a direct contact membrane module was manufactured to be used in a pilot scale membrane distillation process to treat $3m^3/day$ of the digestate produced from anaerobic digestion of livestock manure. In order to investigate the performance of the membrane module, permeate flux was measured with and without spacer inside the module under various condition of temperature difference and cross flow velocity (CFV) through the membrane surfaces. Flux recovery rate after chemical cleaning was also investigated by applying three different cleaning methods. Additionally, thermal energy consumption was theoretically simulated based on actual pilot plant operation conditions. As results, we observed flux of the module with spacer was almost similar to the theoretically predicted value because the installation of spacer reduced the channeling effect inside the module. Under the same operating condition, the permeate flux also increased with increasing temperature difference and CFV. As a result of chemical in-line cleaning using NaOCl and citric acid for the fouled membranes, the recovery rate was 83.7% compared to the initial flux when NaOCl was used alone, and 87% recovery rate was observed when only citric acid was used. However, in the case of using only citric acid, the permeate flux was decreased at a rapid rate. It seemed that a cleaning by NaOCl was more effective to recover the flux of membrane contaminated by the organic matter as compared to a cleaning by citric acid. The total heat energy consumption increased with increasing CFV and temperature difference across the membrane. Thus, further studies should be intensively conducted to obtain a high permeate flux while keeping the energy consumption to a minimum for a practical application of membrane distillation process to treat wastewater.

• Journal of Korean Society on Water Environment
• /
• v.35 no.4
• /
• pp.362-369
• /
• 2019

In this study, biodegradation efficiency improvement of mixed sludge for the anaerobic digestion process in wastewater treatment plant was investigated. In order to release the organic material contained in the sludge cell and promote the hydrolysis step, mixed sludge of 7% TS (Total Solids) was physically shear-treated at a shear strength of 1,000 ~ 4,000 rpm and a maximum of 120 mins. As a result of the comparison between mixed sludge before and after the treatment, the concentration of $SCOD_{Cr}$(Soluble Chemical Oxygen Demand-chromium method) was increased through the conversion of granular organic matter into dissolved organic matter as shear strength and treatment time increases. The solubilization efficiency increased rapidly after 30 min of solubilization application time, and they were 11.23 %, 20.10 %, 22.52 % and 25.43% at 120 min for each shear strength conditions, respectively. Additionally, the BMP(Biochemical Methane Potential) test was conducted with the optimized samples to determine the increase of methane production by the shear pre-treatment. Consequently, methane production of each samples were 0.275, 0.310, 0.323 and $0.335m^3/kg\;VS_{add}$, which indicates that methane production was increased to a maximum of 21.28% compared to the control without the solubilization process ($0.262m^3/kg\;VS_{add}$). As a result, the physical shear-treatment is a promising process for sewage sludge pre-treatment to reduce the organic waste and increase the energy production.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.29 no.4
• /
• pp.67-76
• /
• 2021

Biogasification is a technology that produces environmentally friendly fuel using methane gas generated in the process of stably decomposing and processing organic waste. Biogasification is the most used method for energy conversion of organic waste with high moisture content, and is a useful method for organic waste treatment following the prohibition of direct landfill (2005) and marine dumping (2013). Due to African Swine Fever (ASF), which recently occurred in Korea, recycling of wet feed is prohibited, and consumers such as dry feed and compost are negatively recognized, making it difficult to treat food waste. Accordingly, biogasification is attracting more attention for the treatment and recycling of food waste. Korea's energy consumption amounted to 268.41 106toe, ranking 9th in the world. However, it is an energy-poor country that depends on foreign imports for about 95.8% of its energy supply. Therefore, in Korea, the Renewable Energy Portfolio Standard (RPS) is being introduced. The domestic RPS system sets the weight of the new and renewable energy certificate (REC, Renewable energy certificate) of waste energy lower than that of other renewable energy. Therefore, an additional incentive system is required for the activation of waste-to-energy. In this study, the operation of an anaerobic digester that treats food waste, food waste Leachate and various organic wastes was confirmed. It was intended to be used as basic data for preparing the waste-to-energy incentive system through precise monitoring for a certain period of time. Four sites that produce biogas from organic waste and use them for power generation and heavy gas were selected as target facilities, and field surveys and sampling were conducted. Basic properties analysis was performed on the influent sample of organic waste and the effluent sample according to the treatment process. As a result of the analysis of the properties, the total solids of the digester influent was an average of 12.11%, and the volatile solids of the total solids were confirmed to be 85.86%. BOD and CODcr removal rates were 60.8% and 64.8%. The volatile fatty acids in the influent averaged 55,716 mg/L. It can be confirmed that most of the volatile fatty acids were decomposed and removed with an average reduction rate of 92.3% after anaerobic digestion.

• Journal of Distribution Science
• /
• v.16 no.2
• /
• pp.53-65
• /
• 2018

Purpose - The purpose of this study is to investigate the effect of gamma - irradiation on the effluent from food distribution in the large agricultural and marine products market. This study will contribute to the distribution process as well as the agricultural and fishery distribution facilities. Research design, data, and methodology - In order to reduce the odor, the smell was examined in the anaerobic digestion process by irradiating gamma rays to the wastewater of mixed food discharged from a large restaurant. An odor determination panel list was constructed to determine if the odor was present in the air dilution drainage and the odor concentration was analyzed by instrumental analysis. Results - It was confirmed that the sulfur content increased gradually from 3 months. Ammonia decreased from 33.57ppm at the initial measurement to 4.12 ppm at the end of the experiment. Methane production was highest at 100kGy when exposed to gamma rays of 0-200kGy at pH 12. In other words, it is considered that gamma irradiation doses are most effective at 100kGy and are suitable for large capacity wastewater treatment facilities in terms of economic feasibility. Conclusions - In pre-treatment of compound food wastewater, gamma irradiation is most cost effective when examined at 100kGy. The economic efficiency of the pre-treatment method by gamma irradiation is much higher than the wastewater treatment in the large-scale agricultural and marine products distribution market.

• Korean Journal of Environmental Agriculture
• /
• v.27 no.4
• /
• pp.406-412
• /
• 2008

Biogas plant with anaerobic digestion is receiving high attention as a facility for both livestock waste treatment and electric power generation. Objective of this study was to perform life cycle assessment (LCA) of a biogas plant which incorporates swine and food waste (7:3) as source materials for biogas production. In addition, the biogas production process was compared with the prevalent composting method as a reference in the aspects of green house gas (GHG) reduction potential and environmental impact. The biogas method was capable of reducing 52 kg $CO_2$ eq. emission per ton of swine/food waste, but the composting process was estimated to emit 268 kg $CO_2$ eq. into air. The biogas method was evaluated as more beneficial to the environment by mitigating the impact on abiotic depletion potential (ADP), global warming potential (GWP), ozone depletion potential (ODP), eutrophication potential (EP), and photochemical ozone creation potential (POCP), but not to acidification potential (AP).

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.4
• /
• pp.379-388
• /
• 2006

Two mesophilic trickling bed bioreactors filled with two different types of media, hydrophilic- and hydrophobic-cubes, were designed and conducted for hydrogen production under the anaerobic fermentation of sucrose. Each bioreactor consisted of the column packed with polymeric cubes and inoculated with heat-treated sludge obtained from anaerobic digestion tank. A defined medium containing sucrose was fed by the different hydraulic retention time(HRT), and recycle rate. Hydrogen concentrations in gas-phase were constant, averaging 40% of biogas throughout the operation. Hydrogen production rate was increased till $10.5\;L{\cdot}h^{-1}{\cdot}L^{-1}$ of bioreactor when influent sucrose concentrations and recycle rates were varied. At the same time, the hydrogen production rate with hydrophobic media application was higher than its hydrophilic media application. No methane was detected when the reactor was under a normal operation. The major fermentation by-products in the liquid effluent of the both trickling biofilters were acetate, butyrate and lactate. In order to run in the long term operation of both reactor filled with hydrophilic and hydrophobic media, biofilm accumulation on hydrophilic media and biogas produced should be controlled through some process such as periodical backwashing or gas-purging. Four sample were collected from each reactor on the opposite hydrogen production rate, and their bacterial communities were compared by terminal restriction fragment length polymorphism (T-RFLP) analysis of PCR products generated using bacterial 16s rRNA gene primers (8f and 926r). It was expressed a marked difference in bacterial communities of both reactors. The trickling bed bioreactor with hydrophobic media demonstrates the feasibility of the process to produce hydrogen gas. A likely application of this reactor technology can be hydrogen gas recovery from pre-treatment of high carbohydrate-containing wastewaters.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.8
• /
• pp.561-569
• /
• 2014

This study was carried out to get the characteristics of anaerobic digestion for chemical/biological sludge produced from municipal sewage treatment plant for phosphorus. Anaerobic mesophilic batch tests showed that the ultimate biodegradability of waste activated sludge showed 31%, PACl sludge 24%, Alum sludge 26%, respectively. At the S/I 1.0, 75% of total biodegradable volatile solids (TBVS) of waste activated sludge was degraded with an initial rapid decay coefficient, k1 of $0.1129day^{-1}$ and 74% of TBVS of PACl sludge with k1 of $0.0998day^{-1}$, and 76% of TBVS of Alum sludge with k1 of $0.1091day^{-1}$ for 20 days. During the operation of SCFMRs, the 3 reactor (Control, PACl, Alum) pH maintained 6.7~7.0 and the reactor alkalinity maintained 1,800~ 2,200 mg/L as $CaCO_3$. The average biogas production rates of SCFMRs fed with PACl sludge and Alum sludge were 0.089 v/v-d and 0.091 v/v-d, respectively, which was 27~28% lower than that of the control (0.124 v/v-d) at an HRT (hydraulic retention times) of 20 days. And the methane content during the operation ranged 70~76% in 3 reactor. The average TVS removal efficiency of SCFMRs fed with PACl sludge and Alum sludge were 19.6% and 19.9%, respectively, at an HRT of 20 days, which showed 4% lower than that of the control (23.8%). The average BVS removal efficiency of SCFMRs fed with PACl sludge and Alum sludge were 25.8% and 26.9%, respectively, at an HRT of 20 days, which was 8~9% lower than that of the control (34.5%).

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.2
• /
• pp.67-73
• /
• 2019

In this study, to optimize the production and utilization of biogas for organic waste resources, the precision monitoring of on-site facilities and the energy balance by facility were analyzed, and the solutions for field problems were investigated, and the design and operation guidelines for pretreatment facilities and generators were presented. Gas pre-treatment is required to solve frequent failures and efficiency degradation in operation of high quality refining facilities, and processing processes such as desulfurization, dehumidification, deoxidization, dust treatment, volatile organic compounds, etc. Since these processes are substances that are also eliminated from the high-quality process, quantitative guidelines are not presented in the gas pretreatment process, but are suggested to operate during the processing process as a qualitative guideline. In particular, dust, siloxane, and volatile organic compounds are the main cause of frequent failure of high-quality processes if they are not removed from the gas pretreatment process. Design of the biogas high-quality process. The operation guidelines provide quality standards [Methane content (including propane) of 95% or more] with 90% or more utilization of the total gas generation, two systems, and a margin of 10% or more. It also proposed installing gas equalization tank, installing thermal automatic control system for controlling equalization of auxiliary fuel, installing dehumidification device at the back of high quality for removing moisture generated in the process of gas compression, installing heat-resisting facilities to prevent freezing of facilities in winter and reducing efficiency, and installing membrane facilities in particular.

• Environmental Engineering Research
• /
• v.19 no.1
• /
• pp.83-89
• /
• 2014

The effects of initial solid concentration and microwave irradiation (MWI) time on the hydrolysis of waste activated sludge (WAS) were investigated. MWI time strongly influenced WAS hydrolysis for all initial solid concentrations of 8.20, 31.51, and 52.88 g VSS/L. For all WAS, the volatile suspended solids (VSS) solubilization degree ranged from 35.6% to 38.4% during a total MWI time of 10 min. Soluble chemical oxygen demand (SCOD) concentration increased at a rate proportional to the decrease of VSS during the MWI. However, the clearly different VSS solubilization patterns that were observed during the MWI were explained by the 2-step hydrolysis of WAS, consisting of the initial disintegration of the easily degradable part of the sludge, followed by the subsequent disintegration of the hardly degradable part of the sludge. WAS hydrolysis rates for 3 to 6 min of MWI were significantly lower than those for less than 3 min, or more than 6 min. From these results, 3 min MWI time and WAS of 31.51 g VSS/L (centrifugal thickener WAS) showed the most efficient hydrolysis of WAS at 36.0%. The profiles of total nitrogen (T-N) concentrations corresponded well to the SCOD increases in terms of the empirical formula of bacterial cell mass ($C_5H_7O_2N$). The negligible T-N increase and pH decrease during WAS hydrolysis by MWI will allow the application of this process to subsequent biological processes, such as anaerobic digestion.

• Journal of Korean Society on Water Environment
• /
• v.36 no.2
• /
• pp.137-147
• /
• 2020

A direct contact membrane distillation (DCMD) was applied to treat strong nitrogenous wastewater of anaerobic digestion supernatant (ADS) and human urine (HU). The ammonia transfer was evaluated in terms of specific ammonia transfer (SAT) value, which is the ratio of total ammoniacal nitrogen divided by the amount of water transferred. The acidification resulted in low SAT values and high quality of produced water. The ammonia transfer control in the acidic condition was stronger for HU than ADS due to higher alkalinity (pH 8.8) and ammonia concentration (5700 mg-N/L) of HU. Acidified HU at pH 4 exhibited a SAT value of 1.64 × 10^-5, which was significantly smaller than the SAT value of 3.00 × 10^-3 for the original HU. The low pH enhanced the water flux for ADS, but HU showed a steep decrease in water flux due to enhanced fouling. It was considered that the fouling intensity in acidic conditions depends on the characteristics of the wastewater source. The major foulants on the MD membrane were NaCl, CaCO₃ and CuSO₄ as recognized by the SEM-EDS. Acidified ADS and HU at pH 4 showed relatively high N content of 8.18 % and 28.03 %, respectively, as organic fouling.