• ETRI Journal
• /
• 제28권1호
• /
• pp.1-8
• /
• 2006

A novel all-optical gain-controlled (AOGC) bidirectional amplifier is proposed and demonstrated in a compact structure. The AOGC function using fiber Bragg grating (FBG) pairs controls both directional signals independently, and combinations of optical interleavers and isolators suppress Rayleigh backscattering (RB) noise. The amplifier achieves high and constant gain with a wide dynamic input signal range and low noise figure. The performance does not depend on the input signal conditions, whether static-state or transient signals, or whether there is symmetric or asymmetric data traffic on bidirectional transmission. Transmission comparison experiments between invariable symmetrical and random variable asymmetric bidirectional data traffic verify that the all-optical gain control and bidirectional amplification functions are successfully combined into this proposed amplifier.

• ETRI Journal
• /
• 제29권4호
• /
• pp.536-538
• /
• 2007

We propose and describe the fabrication of a linear power amplifier (LPA) using a new analog feedforward method for the IMT-2000 frequency band (2,110-2,170 MHz). The proposed analog feedforward circuit, which operates without a pilot tone or a microprocessor, is a small and simple structure. When the output power of the fabricated LPA is about 44 dBm for a two-tone input signal in the IMT-2000 frequency band, the magnitude of the intermodulation signals is below -60 dBc and the power efficiency is about 7%. In comparison to the fabricated main amplifier, the magnitude of the third intermodulation signal decreases over 24 dB in the IMT-2000 frequency band.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2002년도 종합학술발표회 논문집 Vol.12 No.1
• /
• pp.413-422
• /
• 2002

A novel photonic bandgap(PBG) structure is proposed and measured for wide bandgap and compact circuit applications. The proposed structure realizes the ultra-wideband bandgap(2-octave) characteristics by superposing two different PBG structures into a coupled double-plane configuration. A low pass filter fabricated using 3-period of the PBG cells shows 2-octave 10 ㏈ stopband from 4.3 to 16.2 ㎓ and 0.2 ㏈ insertion loss in the passband. Moreover, we confirmed that 44∼70 % size reduction can be achieved using the proposed PBG structures. We expect this novel double-plane PBG structure is widely used for compact and wideband circuit applications, such as compact high-efficiency power amplifiers using harmonic tuning techniques.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.155-160
• /
• 2001

The road simulator system can simulate the longitudinal, lateral, and vertical movement changed by road conditions and vehicle dynamic characteristics while driving. This system provides the durability evaluation of vehicle suspensions. The system consists of hydraulic actuators, link mechanism, and servo controller. The hydraulic actuators are specially manufactured using low friction seals to endure high speed movement. The link mechanism is designed in order to minimize the dynamic effect during motion and remove the interference between 3axes actuators. The servo controller is composed of sensors, sensor amplifiers - displacement transducers and load cells, and an industrial PC with DSP board which calculates the control algorithm to control hydraulic actuators. The test results are included to evaluate the performance of this simulator comparing vehicle driving test.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.969-974
• /
• 2003

A simple and cost-effective method for the electrostatic suspension of thin plates like silicon wafers is proposed which is based on a switched voltage control scheme. It operates according to a relay feedback control and deploys only a single high-voltage power supply that can deliver a dc voltage of positive and/or negative polarity. This method possesses the unique feature that no high-voltage amplifiers are needed which leads to a remarkable system simplification relative to conventional methods. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping origination from the air between the electrodes and levitated object. Using this scheme, a 4-inch silicon wafer was levitated stably with airgap variation decreasing down to 1 $\mu\textrm{m}$ at an airgap of 100 $\mu\textrm{m}$

• 한국정밀공학회지
• /
• 제25권3호
• /
• pp.83-92
• /
• 2008

This paper develops the theory for a fault-tolerant, permanent magnet biased, homopolar magnetic bearing. If some of the coils or power amplifiers suddenly fail, the remaining coil currents change via a novel distribution matrix such that the same magnetic forces are maintained before and after failure. Lagrange multiplier optimization with equality constraints is utilized to calculate the optimal distribution matrix that maximizes the load capacity of the failed bearing. Some numerical examples of distribution matrices are provided to illustrate the theory. Simulations show that very much the same dynamic responses (orbits or displacements) are maintained throughout failure events (up to any combination of 3 coils failed for the 6 pole magnetic bearing) while currents and fluxes change significantly. The overall load capacity of the bearing actuator is reduced as coils fail. The same magnetic forces are then preserved up to the load capacity of the failed.

• 한국정밀공학회지
• /
• 제25권3호
• /
• pp.63-72
• /
• 2008

A new method for the electrostatic suspension of disk-shaped objects is proposed which is based on a time-optimal control scheme and deploys only high-voltage power supplies that can deliver dc voltages of positive and/or negative polarity. This method possesses the unique feature that no high-voltage amplifiers are needed which leads to a remarkable system simplification and objects can be suspended stably even in vacuum environment. Using this scheme, an aluminium disk used in a 3.5-inch HDD was suspended stably at an airgap of 0.3mm.

• 한국소음진동공학회논문집
• /
• 제17권11호
• /
• pp.1102-1111
• /
• 2007

The theory for a fault-tolerant control of homopolar magnetic bearings is developed. New coil winding law is utilized such that control fluxes are isolated for an 8-pole homopolar magnetic bearing. Decoupling chokes are not required for the fault tolerant magnetic bearing since C-core fluxes are isolated. If some of the coils or power amplifiers suddenly fail, the remaining coil currents change via a distribution matrix such that the same magnetic forces are maintained before and after failure. Lagrange multiplier optimization with equality constraints is utilized to calculate the optimal distribution matrix that maximizes the load capacity of the failed bearing. Some numerical examples of distribution matrices are provided to illustrate the theory. Simulations show that very much the same dynamic responses (orbits or displacements) are maintained throughout failure events while currents and fluxes change significantly.

• 전기전자학회논문지
• /
• 제11권3호
• /
• pp.122-128
• /
• 2007

Sinusoidal voltage-controlled oscillators (VCOs) based on Colpitts and Hartley oscillators are presented. They consist of a LC parallel-tuned circuit connected in a negative-feedback loop with an OTA-R amplifier and two diode limiters, where the inductor is simulated one realized with temperature-stable linear operational transconductance amplifiers (OTAs) and a grounded capacitor. Prototype VCOs are built with discrete components. The Colpitts VCO exhibits less than 1% nonlinearity in its current-to-frequency transfer characteristic from 4.2 to 21.7 MHz and ${\pm}$95 ppm/$^{\circ}C$ temperature drift of frequency over 0 to $70^{\circ}C$. The total harmonic distortion (THD) is as low as 2.92% with a peak-to-peak amplitude of 0.7 V for a frequency-tuning range of 10.8-32 MHz. The Hartley VCO has the temperature drift and THD of two times higher than those of the Colpitts VCO.

• 전자공학회논문지D
• /
• 제35D권10호
• /
• pp.13-21
• /
• 1998

휘드훠워드 선형 전력 증폭기에 사용하는 적응형 주 신호 제거회로의 주 신호 제거 특성을 해석하였으며 선형 증폭기의 특성을 개선하기 위한 주 신호 제거 오차 제어방법을 제안한다. 이 해석을 통해 정상상태에서 주 신호 제거 율을 정확하게 예측함으로써 부 증폭기의 규격조건 및 주 증폭기의 백 오프 조건 등을 계산할 수 있으며 효율 및 경제성을 고려한 휘드훠워드 선형 증폭기의 최적설계가 가능하다.