• Journal of Conservation Science
• /
• v.29 no.4
• /
• pp.321-332
• /
• 2013

Namwon Singyeri Maaeyeoraejwasang (Rock-Carved Seated Buddha Statue) is composed mainly foliated granite and is different metamorphic grade and weathering degree on rock location. As the results of deterioration evaluation, upper part of the buddha statue was estimated that granularity decomposition was serious and rock strength was lower than lower part. Furthermore organism assessed most effect of among weathering factors. Chl. a amount of organism species were calculated $0.2{\mu}g/cm^2$ of crustaceous lichen, $1.1{\mu}g/cm^2$ of foliose lichen, $2.3{\mu}g/cm^2$ of bryophyte. Organism was taken treatment in order of amount of Chl. a and pre-cleaning, dry cleaning, wet cleaning in sequence. It should be establish conservation plan that strengthening in consideration of lithology characteristics and setting in good condition environment to conserve long-term of Maaeyeoraejwasang.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.1
• /
• pp.22-32
• /
• 2023

In general, when scrap is dissolved in an electric arc furnace, the amount of electric furnace steel dust (EAFD) generated is about 1.5% of the scrap charge amount, and the electric furnace steel dust collected by the bag filter is charged into the Rotary Kiln or Rotary Hearth Furnace (RHF), and the zinc component is recovered as crude zinc oxide, at which time a clinker of Fe-Base is generated. In this research, first, for the efficient resource conversion of electric furnace steel dust, a reduction and roasting experiment was conducted and the reaction kinetics was examined. As a result of the experiment, it was observed that the reduction and roasting reaction was actively conducted in the range of 1100~1150℃, and melting occurred in the range of 1250℃. In the past, this clinker was widely used as a roadbed material for road construction and an Fe-Source for cement production, but in recent years, it has been mainly reclaimed due to strengthening environmental standards. However, landfill treatment is by no means a desirable treatment method due to environmental pollution caused by leachate, expensive landfill costs, and waste of Fe resources. Therefore, in order to more actively recycle the Fe component in the clinker, first of all the clinker was pulverized into an optimal particle size, and anthracite and binder (starch) were added to the magnetic material obtained by specific gravity and magnetic separation for briquet. As a experimental results, it was possible to efficiently separate clinker as Fe component and other slag component by specific gravity and magnetic force. As a results of loading and dissolving the manufactured briquet clinker in an electric arc furnace, it was observed that the unit of power and production yield were clearly improved and the carbon addition effect in molten metal was also somewhat.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.36 no.4
• /
• pp.143-152
• /
• 2020

This study analyzes in detail greenhouse gas emissions in building sector. To this end, this study used data on building characteristics (including building type, region, and construction year) and monthly energy consumptions (including electricity, city gas, and district heat) for all buildings from 2015 to 2018. These data were collected from the National Building Energy Database and the energy consumptions were converted into greenhouse gas (GHG) emissions. The total amount of GHG emissions from the building sector has increased steadily from 2015 (118.1MtCO2eq.) to 2018 (132.6MtCO2eq.). On the other hand, the more recently constructed buildings had lower GHG intensities. This result shows that strengthening building design criteria was effective on the reduction of GHG emissions in buildings, and that the increased buildings contributed to increasing GHG emissions of the building sector. In addition, sales facilities are thought to have the largest reduction potential as they had the highest amount of GHG emissions and GHG intensity. This study is expected to help establish new policies for GHG reduction in building sector as well as to evaluate the effects of existing policies.

• Journal of Plant Biology
• /
• v.9 no.1_2
• /
• pp.17-21
• /
• 1966

The mutual relationships of boron, Ca and sucrose were studied in relation to in vitro pollen growth and pollen bursting, by using conventient pollen from Crinum asiaticum for experiment. Crinum pollen are paticularly sensitive to Ca. Addition of very small amount of boron to cultural media was apparently synergistic to the action of sucrose and Ca in pollen germination and tube elongation. This action was extended to a higher level of boron concentraton. Combined application of boron, Ca and sucrose always gave the better results in pollen growth and protection against pollen bursting much more than when used singly. This indicated that there is a direct relationship between better growth of pollen and increased rigidity of pollen cell wall. A higher level of Ca concentration tended to increase bursting rate of pollen grains and decrease that of pollen tubes, while boron always depressed the rate of bursting. This was considered due to increased failure in pollen germination at high level of Ca that favors pollen tube elongation. The fact that Ca show an antagonistic effect on the suppressive action of high level of boron in pollen growth and shows different effect in response to pollen bursting from boron, suggested mode of Ca and boron action in the presence of sucrose is quiate different, although to increase in rigidity of pollen cell wall by them is in common nature. It was postulated therefore that Ca acts on pectins of pollen cell wall largely as "non-metabolic" and boron as "metabolic" promoter is pollen growth and protecting pollen bursting, since boron and Ca have common nature in strengthening the pollen cell wall but act differently.but act differently.

• Computers and Concrete
• /
• v.19 no.1
• /
• pp.51-58
• /
• 2017

The paper presents the experimental investigations for studying the effect of ground granulated blast furnace slag (GGBFS) on the time-dependent deflection of reinforced concrete (RC) beams due to creep and shrinkage. The RC beams were reinforced with 2-10 mm bars at tension side and subjected to constant sustained two-point loading for the period of 150 days. The amount of cement replacement by GGBFS was varied from 0 to 60% with an increment of 20%. The total deflection was measured at different ages of up to 150 days under sustained loads. The experiments revealed that the time-dependent deflection of the reinforced concrete RC beams containing GGBFS was higher than that of plain concrete RC beams. At 150 days, the average creep and shrinkage deflection of RC beams containing 20%, 40% and 60% GGBFS was 1.25, 1.45 and 1.75 times higher than the plain concrete beams. A new model, which is an extension of authors' earlier model, is proposed to incorporate the effect of GGBFS content in predicting the long-term deflection of RC beams. Besides validating the new model with the current data with higher percentage of tension reinforcement, it was also used to predict the authors' earlier data containing lesser percentage of tension reinforcement with reasonable accuracy.

• Journal of the Korean Society of Safety
• /
• v.23 no.6
• /
• pp.131-137
• /
• 2008

SCP(Sand Compaction Pile) method that forms a composite ground by driving compacted sand piles into the soft ground. This method is one of the soil improvement techniques for reinforcing and strengthening soft ground deposits. This thesis describes the investigation on the behavior of soft ground reinforced with SCP by low improvement ratio. Direct shear test and consolidation test carried out to verified behavior of composite ground reinforced with SCP. Test results were discussed with reference to the amount of consolidation settlement, variation of shear resistance with area replacement ratio and effect of the stress concentration. And, laboratory model loading test carried out to verified the effect of the location and failure mode of reinforced embankment. Residual shear strength varies with the area replacement and constrict load in the low replacement ratio. Calculated stress concentration ratio overestimate than proposed valve by experimental, theoretical and analytical method. As regards the location, improving right below of the top of the slope was more effective than below of the toe of the slope. This thesis carried out to obtain fundamental information of behavior of the composit ground. Hereafter, centrifuge test that reproduce stress state of the in-situ must be necessary through the further study about pile penetration, reinforce position and construct time.

• Management & Information Systems Review
• /
• v.27
• /
• pp.101-129
• /
• 2008

This study introduced the inclusion of Global Value Chain (GVC) as a strategy for the globalization of domestic industries. In addition, this study intended to highlight direct foreign investment as an important opportunity for enhancing the competitiveness of the domestic small and medium firms. That is, globalization could be realized not only through simple capital inflow, but also through domestic industry's participation in the overseas production network. The analysis of the trend and pattern of direct foreign investment revealed that the FDI inflows heavily dependent on the USA and Japan have been diversified steadily over time. In spite of recent decline trend of overall FDI amount, inflows from European countries in machinery and chemical industries have been rising. These rising and diversifying trends in these industries are promising since FDI inflows have the potential of playing an important role in achieving productivity growth of domestic industries, particularly in the area of comparatively fragile industries such as machinery and chemicals. In the same logic, it is crucial for future growth of Korea that the small and medium firms find their competitive edges through strengthening production networks with foreign multi-national companies. Thus, it is suggested that the policy of globalization of small and medium firms should be based on the firm understanding of GVC and FDI pattern of industries.

• Journal of the Korean Ceramic Society
• /
• v.28 no.5
• /
• pp.373-382
• /
• 1991

The effect of Ca/P mole ratio (Ca/P=1.60, 1.67, 1.75) in the initial solution on the mechanical properties of alumina added hydroxyapatite was investigated. Hydroxyapatite was synthesized by precipitation method using Ca(NO3)2$.$4H2O and (NH4)2HPO4 as starting materials and 5 wt% of ${\alpha}$-Al2O3 was added to precipitation solution. The powder was calcined at 800$^{\circ}C$ and sintered at 1,150∼1,400$^{\circ}C$ under water vapor atmosphere. With the increasing of Ca/P mole ration in the initial solution, the amount of tricalcium phosphate formed from the decomposition of hydroxyapatite reduced and the sinterability and mechanical properties were increased. The bending strength and Vickers hardness of the specimen sintered at 1,300$^{\circ}C$ with the Ca/P mole ratio of 1.75 in the initial solution were 230 MPa and 650 kg/$\textrm{mm}^2$, respectively. The improvement of mechanical properties was attributed to not only the effect of Ca/P mole ratio but also the strengthening of sintered body by Al substitution for P ions.

• Journal of Korea Foundry Society
• /
• v.37 no.4
• /
• pp.101-107
• /
• 2017

This study investigated the effect of Pd on the microstructure, tensile and creep properties of Mg-4Al-2Sn (AT42) alloy at a high temperature for transportation-related industrial applications. AT42-xPd (x = 0, 1 and 2 wt. %) alloys were prepared using a permanent mould casting method. The microstructures of the as-cast alloys were characterized by the presence of the intermetallic phases $Mg_{17}Al_{12}$, $Mg_2Sn$ and $Al_4Pd$. The addition of Pd was found to improve the tensile properties of AT42 at room and at elevated temperatures, and to increase the creep resistance at elevated temperatures. A small amount of Pd could markedly improve the tensile properties of AT42 by means of grain-refinement and the dispersion of secondary phase strengthening. Moreover, the thermally stable phase $Al_4Pd$ effectively improves the creep resistance of AT42 due to the strengthened grain boundaries and the suppressed formation of $Mg_{17}Al_{12}$.

• Steel and Composite Structures
• /
• v.42 no.6
• /
• pp.791-804
• /
• 2022

As a type of semi-rigid connection, the top and seat angle connections are popular in current structures owing to their good cyclic performance and simple erection. However, their stiffness and load bearing capacity are relatively insufficient. This study proposes two strengthening methods to further increase the stiffness and strength of bolted-angle joints while maintaining satisfactory energy dissipation capacity (EDC) and ductility. Cyclic loading tests were conducted on six joint specimens with different strengthened angle components. Based on the test results, the influence of the following important factors on the cyclic behavior of steel joint specimens was investigated: the position of the rib stiffeners (edge rib stiffeners and middle rib stiffener), steel strength grade of rib stiffeners (Q345 and Q690), and additional stiffeners or not. In addition, the finite element models of these specimens were built and validated through a comparison of experimental and numerical results. The stiffness and bearing capacity of the bolted-angle joints could be improved significantly by utilizing the novel strengthened joints proposed in this study. Moreover, this can be achieved with almost no increase in the amount of steel required, and the EDC of this joint could also satisfy the requirements of seismic codes from various countries.