• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.475-480
• /
• 2018

We investigated the tribological properties of amorphous carbon (a-C) films deposited with CrC interlayers of various thicknesses as the adhesive layer. A-C and CrC thin films were deposited using the unbalanced magnetron (UBM) sputtering method with graphite and chromium as the targets. CrC films as the interlayer were fabricated under a-C films, and various structural, surface, and tribological properties of a-C films deposited with various CrC interlayer thicknesses were investigated. With various CrC interlayer thicknesses under a-C films, the tribological properties of CrC/a-C films were improved; the increased film thickness exhibited a maximum high hardness of over 27.5 GPa, high elastic modulus of over 242 GPa, critical load of 31 N, residual stress of 1.85 GPa, and a smooth surface below 0.09 nm at the condition of 30-nm CrC thickness.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2002.11a
• /
• pp.54-58
• /
• 2002

The present paper is to investigate the phase stability and soft magnetic properties of amorphous CoNbZr films when Pd is added as a substitution for CoNbZr alloys. The films were prepared by a RF magnetron sputtering method. The CoNbZrPd films deposited on Si wafers exhibited amorphous structures being independent upon the amount of Pd added in the films. On the addition of 4.34% Pd, the excellent soft magnetic characteristics of the films were observed with a coercive force of 0.54 Oe and an anisotropy field of 11 Oe, whereas a coercive force of 1 Oe and an anisotropy field of 3.5 Oe were shown in the film without the addition of Pd. The increased anisotropy field and low coercive force of the films may be attributed to the occupancy of Pd in the preferred sites parallel to the external magnetic field applied on the deposition process. A permeability of about 1100 was kept constant in the operation frequency ranging up to 100 MHz, which can be explained by the Landau-Lifshitz formula.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.89-93
• /
• 1995

Effects of hydrogenation in amorphous silicon rile growths on Solid Phase Crystallization (SPC) was investigated using x-ray diffractometry, energy dispersive Spectroscopy, and Raman spectrum. Interdiffusion of barium(Ba) and aluminum(Al) compounds of corning substrate was observed in both of rf sputtering and LFCVD films under the low temperature(580$^{\circ}C$) annealing. Low degree of crystallinity resulted from the interdiffusion was obtained. Highly applicable degree of crystallinity was obtained through the mechanical damage induced surface activation on amorphous silicon films. X-ray diffraction intensity of (111) orientation was used to characterize the degree of crystallinity of SPC. Nucleation and growth rate in SPC could be controllable through the employed surface treatment. IIydrogenated LPCVD films showed the superior crystallinity to non-hydrogenated sputtering films. Insignificant effects of activation treatment in sputtered film was of activation treatment in sputtered film was observed on SPC.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.123-123
• /
• 2008

In this work, amorphous carbon thin films were deposited for hard mask applications by a reactive particle beam (RPB) assisted sputtering system at room temperature. The depositing characteristics of the films were investigated as functions of operating parameters such as reflector bias voltage and RF plasma power. It was confirmed that the deposition rate increased with increasing the reflector bias voltage and RF plasma power. By an atomic force microscope (AFM), it was revealed that the surface roughness was also increased. The total stress in films was determined by the use of the substrate curvature and its result will be discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.190-191
• /
• 1994

In this paper, We study on the fabrication of amorphous this film of zeromagnetostriction material and the magnetic properties. This films are fabricated by using sputtering method with input power of 400∼607[W], Ar gas pressure of 3∼ 9[mTorr] and target composition of Fe$\sub$4.7/ Co$\sub$74.3/Si$_2$B$\sub$19/. Sample this films with diameter of 14[mm ] and thickness of 27-30[$\mu\textrm{m}$] were obtained through experiments. When we analyzed the magnetic properties before and after annealing with sample thin films, we confirmed that magnetic domain wall amorphous thin films consisted for Neel magnetic domain wall with the width of about 1[$\mu\textrm{m}$].

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.477-477
• /
• 2012

The effects of argon neutral beam (NB) energy on the amorphous carbon (a-C) films were investigated, while the a-C films were deposited by neutral particle beam assisted sputtering (NBAS) system. The deposition characteristics of these films were studied as a function of NB energy (or reflector bias voltage). The film structures were investigated by Raman spectroscopy. The hardness was measured by nano-indentation tests and the optical band gap was measured by UV-visible spectroscopy.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.330-333
• /
• 2005

We investigated the liquid crystal (LC) alignment phenomena using a-C:H and a-C:F:H thin films. Homogeneous alignment is obtained using ion beam treated hydrogenated amorphous carbon (a-C:H) thin films. Homeotropic alignment is obtained using F treated a-C:H thin films, namely, fluorinated amorphous carbon (a-C:F:H) thin films. We investigated the relationship between the surface properties of amorphous carbon based alignment layer and LC alignment phenomena.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.497-500
• /
• 1987

Photoconductive properties of B-doped hydrogenated amorphous silicon thin films prepared by the RF glow discharge decomposition of $SiH_4-B_2H_6$ gas mixtures have been investigated. Experimental results showed that the B-doped hydrogenated amorphous silicon thin films have high photosensitivity and good optical absorption. Therefore these thin films can be used for the photoconductive layer of the vidicon target.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.255-260
• /
• 1998

Behavior of solid phase crystallizations (SPC) of RF sputtered and LPCVD amorphous hydrogenated silicon film were investigated. LPCVD films showed the higher degree of crystallinity and larger grain size than sputtered films. The applicable degree of crystallinity was also obtained from sputtered films. The deposition method of amorphous silicon film influenced the behavior of post annealing SPC. Observed degree of crystallinity of sputtered films strongly depended on the partial pressure of hydrogen in deposition. The higher deposition temperature of sputtering provided the better crystallinity after SPC. Due to the high degree of poly-crystallinity, the retardation of larger grain growth was observed on sputtering film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.340-343
• /
• 2004

The phase transition between amorphous and crystalline states in chalcogenide semiconductor films can controlled by electric pulses or pulsed laser hem: hence some chalcogenide semiconductor films can be applied to electrically write/erase nonvolatile memory devices, where the low conductive amorphous state and the high conductive crystalline state are assigned to binary states. This letters researched into the characteristic of phase change transition in differential Chalcogenide thin films materials. The electrode used Al and experimented on 100nm, 300nm, 500nm respectively.