• Journal of Powder Materials
• /
• v.15 no.4
• /
• pp.292-296
• /
• 2008

The electromagnetic (EM) wave absorption properties of the $Fe_{73}Si_{16}B_7Nb_3Cu_1$ nanocrystalline powder mixed with 5 to 20 vol% of Ni-Zn ferrites has been investigated in a frequency range from 100MHz to 10GHz. Amorphous ribbons prepared by a planar flow casting process were pulverized and milled after annealing at 425 for 1 hour. The powder was mixed with a ferrite powder at various volume ratios to tape-cast into a 1.0mm thick sheet. Results showed that the EM wave absorption sheet with Ni-Zn ferrite powder reduced complex permittivity due to low dielectric constant of ferrite compared with nanocrystalline powder, while that with 5 vol% of ferrite showed relatively higher imaginary part of permeability. The sheet mixed with 5 vol% ferrite powder showed the best electromagnetic wave absorption properties at high frequency ranges, which resulted from the increased imaginary part of permeability due to reduced eddy current.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.4
• /
• pp.339-343
• /
• 2006

We observed the application possibility of inductive coupler for the underground high-voltage power line communication by means of analysis of signal transmission characteristics and magnetic properties on annealing temperatures for high-permeability Fe-base amorphous alloys. The best electromagnetic and transmission characteristics were shown in nano-crystalline precipitated alloy annealed at temperature $510^{\circ}C$. The transmission characteristics in the low-frequency band depend on permeability of magnetic core materials and its properties of high-frequency band can be improved by impedance matching. Using the high pass filter embedded in the coupler, other noise signal band except for communication signals could be cut off.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1402-1405
• /
• 2006

Using a indium zinc oxide (IZO) alloy target with a ratio of 90:10 in wt%, highly transparent conducting oxide (TCO) thin films are prepared on polyethersulfone (PES) substrates by lowfrequency (LF) magnetron sputtering system. These films have amorphous structures with excellent electrical stability, surface uniformity and high optical transmittance. Experiments were carried out as a function of applied voltage. At optimal deposition conditions, thin films of IZO with a sheet resistance of 29 ohm/sq. and an optical transmission of over 82 % in the visible spectrum range were achieved. The IZO thin films fabricated by this method do not require substrate heating during the film preparation or any additional post-deposition annealing treatment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.2
• /
• pp.33-40
• /
• 1994

알루미늄 코팅막은 부식환경으로부터 강판을 보호하는 데에 자주 사용된다. 그러나 이 코팅막은 때때로 사용조건에 따라 제한을 받는다. 아무리 강판상에 치밀한 양질막을 코팅시켰다 할지라도, 사용중 이 피막이 손상을 받아서 강판이 노출되는 경우는 강판과의 갈바닉(Galvanic)작용으로 급격한 부식을 일으킨다. 본 연구는 내식성 개선을 목적으로 해서, 고밀착성의 코팅막을 제공하는 비평형프라즈마 프로세스인 이온프레이팅법에 의해 냉간압연강판상에 Al-Mg합금 코팅막을 제작했다. 제작된 막들은 우선, EMPA측정에 의해 원소조성분석을 한 후, 상구조분석 및 표.단면의 몰포로지(Molphology)를 X선 회절 및 주사형 전자현미경(SEM)에 의해 관찰했다. 또한, 이들막은 탈기시킨 3%NaCl용액중 양극분극 측정을 통해서 내식특성에 대한 평가를 행했다. 이들의 결과에 의하면, 알루미늄과 마그네슘의 조성비에 따라 주상, 미결정 및 아몰포스(Amorphous)조직을 보이는 금속간화합물이나 고용체의 Al-Mg박막이 나타났다. 이들 Al-Mg합금 코팅막은 강판과의 갈바닉 부식작용에 대한 방지 및 부동태 피막의 형성을 촉진하는 등의 좋은 내식성을 나타냈다.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.628-633
• /
• 1996

Large saturation magnetization $4pM_s$ is essentially required for soft magnetic thin layers used in magnetic recording devices. Amorphous Co-based alloys and Fe-Co alloys may be regarded as one of the candidates for soft magnetic materials which possess large $4\piM_s$. Some preparation process to improve soft magnetism of these films were performed in this study. Addition of Ta seemed to be effective to change the magnetostriction constant $\lambda$ from positive value to negative one. The magnetoelastic energy $K_e$ is strongly dependent on $\lambda$. $(Co_{95.7}Zr_{4.3})_{100-x}Ta_x$ films with $K_e$ of negative value have sufficiently soft magnetic characteristics. $Fe_{90}Co_{10}$ alloy exhibits extremely large $4\piM_s$, of about 24 kG. Addition of N and Ta to $Fe_{90}Co_{10}$ films improved the soft magnetism of them. The $Fe_{82.0}Co_{7.6}Ta_{10.4}$:N/Ti multilayered films exhibit better soft magnetic properties and better thermal stability than Fe-Co-Ta:N singlelayer films.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1365-1372
• /
• 2001

In the planar flow casting(PFC) process, the conditions of the melt puddle between nozzle and rotating wheel affect significantly the quality and dimensional uniformity of the downstream ribbon. For stable puddle formation, the nozzle is placed very close to the quenching wheel, so the surface-tension and wall-adhesion forces have an important effect upon the fluid flow.\`In this study the planar flow casting process has been mode]ed using the VOF method for free surface tracking. The transient puddle formation from the present analysis shows good agreements with the previous experimental results. Furthermore, the variation of melt temperature and the corresponding cooling rate of the melt have been examined. The present results also show how the melt puddle can be farmed on the rotating substrate, how the melt flows within the puddle, and how the changes of the process variables affect the puddle formation and its corresponding fluid flow and heat transfer behavior.

• Korean Journal of Crystallography
• /
• v.15 no.2
• /
• pp.104-109
• /
• 2004

The mechanical synthesis of thermoelectric material $FeSi_2$ by planetary ball mill has been investigated. The homogeneous and amorphous mixture of Fe-Si has been obtained by mechanical alloying for 850 rpm-40 min. The $\beta-FeSi_2$ powder could be synthesized by 1123 K-3 hr annealing heat treatment after mechanical alloying for 850 rpm-10, 20, and 40 min. The ceramic samples doped with the maximum content up to $10\;at.\;\%$ Co have exhibited semiconduction phenomena and maximum thermoelectric powder at 440K.

• Journal of Welding and Joining
• /
• v.9 no.4
• /
• pp.28-39
• /
• 1991

The change of microstructure in the bonded interlayer and mechanical properties of the joints were investigated during Transient Liquid Phase Diffusion Bonding(TLP bonding) of STS304/SM17C and STS304/SM45C couples using Ni base amorphous alloys added boron and prepared alloy as insert metal. Main experimental results obtained in this study are as follows: 1) Isothermal solidification process was completed much faster than theoretically expected time, 14ks at 1473K temperature. Its completion times were 3.6ks at 1423K, 2.5ks at 1473K and 1.6ks at 1523K respectively. 2) As the concentration of boron in the insert metal increased, the more borides were precipitated near bonded interlayer and grain boundary of STS304 side during isothermal solidification process, its products were $M_{23}P(C,B)_6}_3)$ The formation of grain boundary during isothermal solidification process was completed at structural carbon steel after starting the solidfication at STS304 stainless steel. 4) The highest value of hardness was obtained at bonded interface of STS304 side. The desirable tensile properties were obtained from STS304/SM17C, STS304/SM45C using MBF50 and experimentally prepared insert metal with low boron concentration.

• Journal of Korea Technology Innovation Society
• /
• v.8 no.3
• /
• pp.1027-1059
• /
• 2005

The purpose of this paper is to analyze the dynamic characteristics of innovation sources such as scientific knowledges, processing technologies and user's needs in advanced metals technology. The journal articles data of four advanced materials are analyzed; amorphous metals, superplastic materials, shape memory alloys and aluminum-lithium alloy. Some regularities are found from the analysis of the four materials. The innovation proceeds through close interactions among the innovation sources. As the innovation proceeds, the relative importance of each source changes: scientific knowledge initiates the innovation and becomes the most important source in the first phase, then the processing technologies increase importance in the second phase, and then scientific knowledge, again, becomes the leading factor of innovation. Scientific knowledge and processing technology take turns leading the innovation. The impacts of users' needs to the innovation increase more and more as innovation proceeds. The results of analysis imply to the policy makers that emphasis of policy, and therefore the allocation of sources for innovation, should vary along the phases in the life cycle of advanced metals technology.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.111-111
• /
• 2016

Two step PEO ceramic coatings were formed on AZ91 magnesium alloy in $ZrO_2$ nanoparticles and $K_2ZrF_6$ based colloidal electrolyte solution for various voltages. Surface and layers tructure of the coatings was analyzed using SEM (ScanningElectronMicroscope). Structure analysis revealed that surface of the coating was transferred from individual pancake or craters-based structure to cluster-based structure with increasing the voltage of the secondary step process. Further, it was confirmed that the cluster zone was richin Zr-based complexes and formed due to high intensives parks. Increase in the Zr contents as discovered from the EDS analysis confirmed the rise in amorphous form of the Zr-based species, which justified the results of XRD where no increase in the intensity of Zr-based species was observed with increase in voltage. Potentiodynamic polarizariotion and impedance spectroscopy techniques were used to evaluate the corrosion performance of the coatings. The highest corrosion resistance was found for coatings prepared at 240V. The same specimen was found having highest and uniform vickers hardness ~1070.5 HV. The superior mechanical and electrochemical properties of the said coating can be attributed to the defect-less microstructure and the optimal role of $ZrO_2$ nanoparticles in the secondary PEO process at 240V.