• 한국분말재료학회지
• /
• 제11권6호
• /
• pp.451-461
• /
• 2004

Dry sliding wear behavior of electro-pressure sintered Co-Fe and Co-Ni compacts was investigated. Pin-on-disk wear tests were performed on the sintered Co-Fe, Co-Ni disks against alumina $(Al_2O_3)$ and silica $(SiO_2)$ balls at various loads ranging from 3N to 12N. A constant sliding speed of 0.1m/sec was employed. Wear rate was calculated by dividing the weight loss of a specimen by the measured specific gravity and sliding dis-tance. Worn surfaces and cross-sections of the specimens were examined using an SEM and EDS to investigate wear mechanism of the compacts. The wear behavior of the compacts were discussed as a function of their com-position. Effects of mechancial properties of the compact as well as oxide layers formed on wearing surface on the wear were also discussed.

• 한국연초학회지
• /
• 제36권1호
• /
• pp.12-19
• /
• 2014

A matrix solid-phase dispersion (MSPD) method was developed for extracting and cleaning-up the selected agrochemicals in tobacco using gas chromatography-mass spectrometry with selected ion monitoring (GC/MS-SIM). Different parameters of the method were investigated and optimized, such as the type of solid-phase (alumina, $C_{18}$ and Florisil) and eluent (acetone, acetonitrile, ethylacetate and n-hexane). The best results were obtained using 0.5 g of tobacco sample, 1.0 g of $C_{18}$ as dispersant sorbent, 1.0 g of Florisil as clean-up sorbent and acetonitile saturated with n-hexane as eluting solvent. The method was validated using tobacco samples fortified with agrochemicals at their different concentration levels. This method gave good linearity for the selected agrochemicals of ranging from $0.01{\mu}g/mL$ to $0.1{\mu}g/mL$. Recoveries of the selected agrochemicals in tobacco were more than 80 % and reproducibilities were found to be better than 10 % RSD. Those results suggested that the analytical procedure including MSPD method in combining with GC/MS could be applicable to the rapid determination often the selected agrochemicals in tobacco.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.32-38
• /
• 2009

Silicon nitride samples with aligned whisker seeds were prepared with different amounts of yttria and alumina as the sintering additives. Their sintering behaviors and the microstructural developments between $1850^{\circ}C$ and $2050^{\circ}C$ were examined. The sample with larger amount of the sintering additives showed faster densification and grain growth. Even though addition of the aligned whisker seeds slightly retarded densification of silicon nitride, it improved the flexural strength and the fracture toughness. Both the flexural strength and the fracture toughness of silicon nitride with the aligned whisker seeds were increased as the amount of the sintering additives was increased.

• 소성∙가공
• /
• 제20권7호
• /
• pp.479-484
• /
• 2011

Dry sliding wear behavior of AISI 52100 steel that has a pearlite or bainite microstructure was characterized to explore the effect of microstructure on the wear of the steel. Isothermal heat treatments were employed to obtain the different microstructures. Pin-on-disk type wear tests of the steel disk were performed at loads of 25~125N in air against an alumina ball. Sliding speed and wear distance used were 0.1m/sec and 300m, respectively. Worn surfaces, wear debris and cross-sections of the worn surfaces were examined with SEM to investigate the wear mechanism of the steel. Hardness of the steel was also evaluated. Wear rate of the steel was correlated with the hardness and the microstructure. On the whole, wear resistance increased with an increase in hardness. However, the pearlite microstructure showed superior wear resistance as compared to the bainite microstructure with a similar hardness. The effect of the microstructure on the wear rate was attributed to the morphological differences of the carbide in the microstructure, which was found to have a significant effect on strain hardening during the wear.

• 대한전자공학회논문지
• /
• 제9권5호
• /
• pp.27-33
• /
• 1972

This paper describes the computer-aided design, fabrication and performance of high Q and high gain active filters suitable for microminiaturization in the frequency range of 10-800MHz, based on the negative resistance operation of a transistor. 48 as high as 1000 and a transducer gain as high as 35dB can readily be obtained with a single-transistor amplifier and with an inductance as small as a few nH at higher frequencies and 150 nH at lower frequencies in tile above frequency range. The gain of the proposed active filter can be stoabilized within $\pm$ 1.5 dB over the temperature range -1$0^{\circ}C$ to +5$0^{\circ}C$ and the temperature dependence of the center frequency is tapicalla 50ppm/$^{\circ}C$. An experimental FM receiver utilizing these fitters and operating at a carrier frequency of 92 MH3 was built. The whole circuit was fabricated on eight alumina substrates of by the thick-film hybrid IC technique and the coils are constructed, for miniaturization, in a spiral form of 3 or 4 turns of enamel copper wire with an overall diameter of about 5mm. The test results are also reported in this paper.

• 한국디지털건축인테리어학회논문집
• /
• 제12권3호
• /
• pp.59-66
• /
• 2012

Autoclaved Lightweight Concrete(ALC) features such as a high performance insulation, the fire resistance, the advantage of easy handing construction, and lightweight panels applied the curtain wall system. ALC materials are certified as non-toxic environmental and eco-friendly productions. But ALC external panels mixed with blast furnace slag pounder and silica fume have to be coated with a stucco compound or plaster because of resisting the ambient environment. This study is that mixing tests to evaluate a performance analysis of exterior paints to be make-up pigments(organic or inorganic) coated with panel surface. Testing compared by KS F 2476; flow test, KS F 2426; compression strength test, KS F 2762; bond strength test. In results, the case of the inorganic binder, ratio of alumina cement : anhydrite is 90:10 to 80:20 at the highest level of intensity. In the case of the organic binder, adhesive strength rating at surface of ALC, the pullout strength is below 0.5 $N/mm^2$ but the normal concrete is over 2.0$N/mm^2$. A contents ratio of EVA resin is more than 3% and then bond strength is effectively.

• 한국세라믹학회지
• /
• 제43권4호
• /
• pp.242-246
• /
• 2006

[ ${\alpha}-Al_2O_3$ ] nanopowders were fabricated by the thermal decomposition and synthetic of Ammonium Aluminum Carbonate Hydroxide (AACH). Crystallite size of 5 to 8 nm were fabricated when reaction temperature of AACH was low, $8^{\circ}C$, and the highest $[NH_4{^+}][AlO(OH)_n{(SO_4){^-}}_{3-n/2}][HCO_3]$ ionic concentration to pH of the Ammonium Hydrogen Carbonate (AHC) aqueous solution was 10. The phase transformation fem $NH_4Al(SO_4)_2$, rhombohedral $(Al_2(SO_4)_3)$, amorphous-, ${\theta}-,\;{\alpha}-Al_2O_3$ was examined at each temperature according to the AACH. A Time-Temperature-Transformation (TTT) diagram for thermal decomposition in air was determined. Homogeneous, spherical nanopowders with a particle size of 70 nm were obtained by firing the 5 to 8 m crystallites, which had been synthesized from AACH at pH 10 and $8^{\circ}C,\;at\;1150^{\circ}C$ for 3 h in air.

• 한국전기전자재료학회논문지
• /
• 제17권4호
• /
• pp.378-383
• /
• 2004

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten(W) on SiO$_2$ layer, the Ti/TiN barrier layer is usually deposited onto SiO$_2$ for increasing adhesion ability with W film. Generally, for the W-CMP(chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidant on the polishing selectivity of W/Ti/TiN layer was investigated. The alumina(A1$_2$O$_3$)-based slurry with $H_2O$$_2$ as the oxidizer was used for CMP applications. As an experimental result, for the case of 5 wt％ oxidizer added, the removal rates were improved and polishing selectivity of 1.4:1 was obtained. It was also found that the CMP characteristics of W and Ti metal layer including surface roughness were strongly dependent on the amounts of $H_2O$$_2$ oxidizer.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 춘계학술발표회 논문집
• /
• pp.141-142
• /
• 2012

Recently, surface texturing by atmospheric laser processing has been received lots of attention to improve the tribological performance of various surfaces and this laser texturing of surfaces could be considered in a large extent to improve tribological performance of PVD coated surface. Surface texturing could be performed by various manufacturing techniques such as indentation with hard materials, ion etching, abrasive jet machining, lithography, and Laser Surface Texturing (LST). Out of all these techniques, however it is generally accepted that laser surface texturing (LST) by atmospheric laser processing offers the most promising process as LST is very fast, environmentally-friendly, easy to control the shape and size of the microdimples. In this work various preliminary experimental results from the laser texturing on the PVD-coated steel substrate will be presented. Our results indicated that laser texturing definitely affect the tribological performance of the surfaces and the size as well as pattern type of laser texturing are one of the key factors. From the wear tests against an alumina counterpart ball at room temperature under oil-lubricated condition, laser surface texturing on the CrZrSiN films reduced the friction coefficients by approximately more than 5 times in the case of narrow patterned surfaces.

• 한국광학회지
• /
• 제3권3호
• /
• pp.178-182
• /
• 1992

내경 1.6cm, 길이 50cm의 알루미나 세라믹 방전관을 사용하여 방전전극간의 거리가 45cm인 공쟁식 방전가열형 구리증기레이저를 제작하였다. 방전가열 및 여기를 위한 6kV, 500mA 정격의 직류 고전압 전원장치, 1.8H의 중전 인덕터와 5nF의 에너지저장 캐패시터를 포함하는 resonant charging 방식의 고전압 충전회로와 1-7kHz 범위의 펄스반복률로 동작하는 thyratron 구동회로가 각각 설계 제작되었다. 개발된 레이저장치는 방전관의 온도 $1350^{\circ}C$ 부근에서 발진을 시작하였고, 충전전압 12kV, 펄스반복률 4.5kHz, 네온완충기체압력 50mbar, 동작온도 $1460^{\circ}C$일 때 0.7W의 최대평균 출력을 얻었다.