• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.393-398
• /
• 2005

Suspended fine mineral particles are deposited at the areas with low flow velocity and low transportation capacity in rivers, reservoirs and lakes. It can be contaminated by heavy metals. Examples of problem fields art dredging of sediment, water pollutants, and maintenance of navigation channels and construction works. To deal with the settling problems it is necessary to understand tile physico-chemical characteristics of cohesive sediment under varying density of particle and ion addition(NaOH, HCl, NaCl), which is dissolved in river, because fine-grained cohesive sediment can lead to flocculation with the physico-chemical influences and takes different characteristics. Experiments with fresh and saline water are followed with fine-grained sediments(alumina and quartz) in settling columns. Settling velocity of suspended fine particles in still water was measured with a pressure sensor(maximum 10 mbar). Until the initial concentration of 20,000 mg/1 of alumina and quartz the settling velocity was on the increase. Above this initial concentration was it on the decrease. In an acid condition, which causes strong flocculation, average settling velocity of quartz powder was high. In an alkaline water low average settling velocity of it was observed. However, alumina behaved exactly contrarily.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.704-707
• /
• 1997

The preparation of alumina sol for fine chemical field from kaolin-derived aluminum sulfate solution is performed. Noncrystalline AlO(OH) was prepared by dropping ammonia water into aluminum sufate solution with stirring. Acetetic acid was added to form the electrical double layers on the particle surface of the slurry, which resulted in a stable sol. The influence of the reaction temperature, reaction time, acetetic acid concentration on the preparation of alumina sol were investigated. Dispersed colloid particles of AlO(OH) were prepared at the reaction temperature of $50{\sim}90^{\circ}C$ and 1.6 A/C = 1.6 (molar ratio), regardless of the reaction time. Stable alumina sol having a particle size of about 5~10 nm was prepared in the range 1~5 vol% alumina content.

• Tribology and Lubricants
• /
• v.33 no.5
• /
• pp.220-227
• /
• 2017

In this work, carbon nanotube and nano-size alumina particle are exploited as additive for lubrication experiment. We used pin-on-disk type tribometer to investigate the tribological characteristics of lubricants with respect to additives and rotational speed. We conducted more than 15 trials of tribotests for two hours for each specimen to obtain stable and accurate frictional force and to create measurable wear track on the substrate. We conducted tests at the boundary/mixed lubrication regime to evaluate the influence of additives on the tribological characteristics. We found that the friction coefficient decreased as the rotational speed increased and as additives were added. In particular, the reduction of friction by adding additives was more significant at low rotational speed than at high rotational speed. We speculate that the additives helped to separate and protect the two contacting surfaces at low speed, while the influence of additives was not significant at high speed since sufficiently thick lubricant film was formed. The wear of the substrate was also reduced by adding additives to the lubricant. However, in contrast to friction, the amount of wear at high rotational speed was less when alumina particles were added to the lubricant than the amount of wear at low speed. We speculate that the increased wear at low rotational speed is as a result of the intermittent abrasive wear caused by alumina particles with uneven shape, while the reduced wear at high speed is as a result of sufficient film thickness which prevented the abrasive wear.

• Journal of the Korean Ceramic Society
• /
• v.27 no.6
• /
• pp.755-762
• /
• 1990

The tungsten paste was printed on the surface of 92% alumina sheet which was made by type casting process. The printed tungsten was bonded on the Al2O3 by co-firing in reducing atmosphere. During the co-firing, the binder burn-out was easier in wet H2 atmosphere than in dry H2, which affected sintered density. In practically, the use of wet H2 above 100$0^{\circ}C$ was beneficial for density of alumina and bond strength. This phenomena occured more distinctly when atmosphere varied from dry H2 to wet H2 than varied dew point in wet H2. In wet H2, the improvement in bonding strength can be attributed to good glass migration into the metal layer due to inhibition of the tungsten particle growth, with increase of alumina density, at the temperatrue higher than 100$0^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.30 no.4
• /
• pp.299-308
• /
• 1993

Dispersant was used to avoid the agglomeration of aluminum hydrate precipitate and improve the sinterability of calcined alumina powder. The mean particle size of the aluminum hydrate precipitates was 0.26${\mu}{\textrm}{m}$ and 0.44${\mu}{\textrm}{m}$ when ball-milled with and without dispersant, respectively. After calcination at 110$0^{\circ}C$ for 5 hours, the size of the alumina powder without dispersant increased to 0.84${\mu}{\textrm}{m}$, while with dispersant slightly decreased to 0.22${\mu}{\textrm}{m}$. The most thermally active alumina powder was obtained from the sample calcined at 110$0^{\circ}C$ for 5 hours with the 1% dispersant concentration. Using the calcined alumina powder at the above optimized condition, the specimen showed fired density of 3.94g/㎤, 4-point MOR of 364MPa, and KIC of 3.26MPam1/2 after sintered at 155$0^{\circ}C$ for 3 hours.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.17-27
• /
• 2010

KSLV-I KM plume including alumina particle has been studied using the continuum solver. Alumina particles are assumed to have 7 different diameters, and the specific ratio of the plume gas is assumed to be 1.2, with which the internal nozzle flow characteristics are similar to those of the chemically equilibrium analysis results. The results showed that the expansion angle of the particles is smaller than that of the gas phase, and that the big sized alumina particles are gathered in the plume core and the expansion angles of the big sized particles are smaller than those of the light particles. When the emissivity of the particles are assumed to be 0.1, the radiative heat flux is equivalent to those measured during the flight test of KSLV-I.

• Journal of the Korean Ceramic Society
• /
• v.51 no.6
• /
• pp.560-565
• /
• 2014

Alumina nano-asperites were grown on plate-like alumina particles of which the surface had been covered with a capping agent to control the asperite formation sites on the particles. Utilized alumina source for asperite was nano sized ${\gamma}$-alumina, which was prepared by calcination of $Al(OH)_3$ at $600^{\circ}C$; silica suspension was used as the capping agent. Plate like alumina particles were covered by silica suspension and continuously heat-treated to $900^{\circ}C$ with nano sized ${\gamma}$-alumina, as the source material, under molten-salt atmosphere. Asperite growing site were controlled by the degree of coating of the capping agent; 10-20 nanosize of ${\theta}$-alumina were formed on the particle surface. On the other hand, alumina particles without capping agent were observed to undergo only step-like crystal growth during heat-treatment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.317-320
• /
• 1997

The paper reports on a study of the influence of the size of the particles of alumina trihydrate(ATH) filler on the surface aging characteristics of ehylene propylene diene terpolymer(EPDM). A fixed 100pph concentration of the filler of ATH was used (or all particle sizes from 0.7 to 20$\mu\textrm{m}$, It is show that hysteresis of contact angle and leakage current increase with increasing particle size, whereas tracking resistance decrease with increasing particle size.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.347-356
• /
• 1993

In joining alumina ceramics to metal by using Mo-Mn metallizing process the effects of metallizing thickness, temperature, and the composition of paste on the bond strength and the microstructure of joining interface were investigated. The bond strength variation in the range of metallizing temperature, 1350~155$0^{\circ}C$ was more than 150MPa above 145$0^{\circ}C$ and the optimum metallizing thickness was 30${\mu}{\textrm}{m}$. The optimum contents of Mn in Mo-Mn paste was 5% due to the bond strength decrease with the increase of addition. The effect of SiO2 addition in paste on bond strength was saturated around 200MPa. It was also observed that as the particle size of Mo decreased, the joinning with higher bond strength was shown in spite of low metallizing temperature.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.17-24
• /
• 1995

The TEA complex polymeric sol was prepared by the alkoxide sol-gel method. The purpsoe of this experiment was to vefity the particle shape in the sol from the investigation of the rheological properties. TEA retarded hydrolysis rate by the reaction with alkoxide enough to make a stable transparent sol in the wide range of composition. From the results of the viscosity change with time, the optimum mole ratio for spinning was selected as 0.5 mole of TEA, 3 mole of H2O and the optimum viscosity was 104 cPs. The rheological behavior of the sol showed that the particle shape in the sol was linear, which was adequate for fiber drawing.