• 한국세라믹학회지
• /
• 제28권4호
• /
• pp.338-346
• /
• 1991

The alumina-titania composite powders coated with Al2O3 were prepared by the method of hydrolysis-deposition of mixed aluminium salt solution of Al2(SO)4-Al(NO3)3-Urea. The effects of coating-process parameters on the characteristics of coated composite powders were also investigated. As the content of TiO2 dispersed in deionized water increased, the coated composite powders were found to be more uniform in size and unagglomerated. When TiO2 powders were coated for 30 min, the optimum TiO2 content in the coating process was 400 mg/ι. The size of TiO2 particle was increased approximately from 0.7${\mu}{\textrm}{m}$ to 1.0${\mu}{\textrm}{m}$ through coating of Al2O3. The IEP of coated composite powders was pH=8.3 identical to the value of aluminium hydroxides and the zeta-potential showed nearly similar values each other. When heat treating coated composite powders at 130$0^{\circ}C$, only two phases of TiO2(rutile) and Al2TiO5 were observed. These results showed that the suface of TiO2 could be uniformly coated with the aluminium hydroxide.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.66-78
• /
• 1998

the microstructure and mechanical properties of seeded and ball-milled dry gels prepared by boehmite sol-gel method were discussed. The densification of seeded gels was improved with increasing seed content namely the number of seed The number of seed was 1.09, 3.35, 5.72${\times}$1012/cm3 boehmite when seeded with 1, 3, 5wt% respectively The ball milled gel contained about 0.5wt% seed and the number of seed was 4.72${\times}$1012/cm3 boehmite. The sintered density of 5wt% seeded gel was below 80% when sintered at 1300$^{\circ}C$ for 1h. On the other hand that of ball milled gel was very improved and reached to 97% In the case of 3wt% seeded gels the density over 97% was attained when sintered at 1500$^{\circ}C$for 1h. and the grain of the sintered body was several micrometers in size. However the sintered body of ball milled gel showed grain size of submicrometer when sintered at 1300$^{\circ}C$ for 1h. And this specimen showed highest harness value of 1900kg/mm2 The fracture toughness increased with increasing sintering temperature. The sintered body of ball milled gel showed the largest grain size and the highest fracture toughness without regard to sint-ering temperature.

• 한국세라믹학회지
• /
• 제37권3호
• /
• pp.211-218
• /
• 2000

The attrition-milled powder mixtures of Al and Al2O3 were oxidized below 140$0^{\circ}C$ for 1 hr and post-sintered at 150$0^{\circ}C$ and 1$600^{\circ}C$ for 2 hr. During attrition milling, ZrO2 was added to the system by grinding effect of ZrO2 balls. The average particle size of the powder mixtures was decreased by the attrition milling as the aluminum content decrease. Above 120$0^{\circ}C$, sintering behaviro was observed on the fine Al2O3 particles resulted from the oxidation of Al. The specimens heat-treated at 140$0^{\circ}C$ for 1 hr showed the bending strength of 166 MPa and hardness of 220 MPa. The specimens post-sintered at 1$600^{\circ}C$ for 2hr had a linear shrinkage of 9~12% and a relative density of about 95%. After the post-sintering, the specimens having 55 vol% Al content revealed the bending strength of 513 MPa and hardness of 718 MPa. The Weibull modulus to the bending strength was about 16.

• 한국결정학회지
• /
• 제8권2호
• /
• pp.89-96
• /
• 1997

본 연구는 fine ceramics의 합성법을 traditional ceramics의 합성에 적용하는 연구의 일환으로 내화재료용 mullite합성법을 개발하고자 한다. 출발원료로는 알루미나 함량이 높은 하동 kaolin 과 boehmite를 사용하였으며 합성법은 gel coating법을 사용하였다. 그 결과 1350℃에서 미반응 silica와 corundum이 존재하지 않는 단일상의 mullite를 합성할 수 있었으며 1700℃로 소성한 분말의 경우 mullite 생성율은 80%로 나타났다. 이 때 부피비중은 2.56, 흡수율은 1.9%, 상온꺽임강도는 169 MPa의 값을 나타내어 우수한 내화재료로의 활용이 가능하다고 생각된다.

• 한국세라믹학회지
• /
• 제44권5호
• /
• pp.184-189
• /
• 2007

In this study, a novel-processing route for producing microcellular cordierite ceramics has been developed. The proposed strategy for making the microcellular cordierite ceramics involves three steps: (i) fabricating ceramic-filled preceramic foams by heating a mixture of polysiloxane, expandable microspheres, talc, and alumina in a mold, (ii) cross-linking the foamed body, and (iii) transforming the body into microcellular cordierite ceramics by sintering. Cu jig was used for near net shaping in the foaming step. The experimental variables such as the shape of foaming jig and the content of expendable microsphere were investigated. By controlling the content of expendable microsphere, it was possible to make the porous cordierite ceramics with cell density of ${\sim}1.0{\times}10^9\;cells/cm^3$.

• 한국수소및신에너지학회논문집
• /
• 제32권6호
• /
• pp.464-469
• /
• 2021

A reforming catalyst for hydrogen production from ammonia is being studied. Non-novel metal based Ni catalysts for use in ammonia reforming processes are being developed. In this study, the ammonia reforming characteristics according to Ni content of the alumina pellet supported catalyst in the mid-temperature region were investigated under different space velocity. 20 Ni and 3,000 h^-1 showed the best catalytic activity with ammonia conversion of 63% among all conditions.

• 한국농공학회논문집
• /
• 제48권1호
• /
• pp.51-60
• /
• 2006

This study was conducted to investigate experimentally the drying shrinkage and the strength properties of redispersible SBR and PAE powder-modified mortars. Polymer-cement ratio, content of shrinkage-reducing agent and antifoamer content were manipulated as the experimental variables. The peculiarity of this study is to obtain a high early-age strength by using the portland cement and alumina cement with the ratio of 8 : 2. Until 7 days of age, the drying shrinkage remarkably increased up to $1\~2\times10^{-4}$, while it tended to decrease as the ratio of polymer to cement ratio and the content of shrinkage-reducing agent increased. Polymer-cement ratio was effective in improving the flexural, tensile and adhesive strengths: As the ratio increased, the strengths correspondingly increased. The flexural strength was in the range of $7\~11$ MPa, the tensile strength was $3.5\~5$ MPa and the adhesive strength was $1.2\~3.9$ MPa. On the other hand, the compressive strength tended to decrease as the polymer-cement ratio increased, and it was in the range of $23\~39$ MPa. All strengths, flexural, tensile, adhesive and compressive strengths, decreased as the content of powder shrinkage-reducing agent increased. It turned out that the polymer-cement ratio influenced more on the behavior of drying shrinkage and the properties of strength than the powder shrinkage-reducing agent did.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.38.1-38.1
• /
• 2009

Plasma etching is an essential process for electronic device industries and the particulate contamination during plasma etching has been interested as a big issue for the yield of productivity. The oxynitride glasses have a merit to prevent particulate contamination due to their amorphous structure and plasma etching resistance. The YSiAlON oxynitride glasses with increasing nitrogen content were manufactured. Each oxynitride glasses were fluorine-plasma etched and their plasma etching rate and surface roughness were compared with reference materials such as sapphire, alumina and quartz. The reinforcement mechanism of plasma etching resistance of the YSiAlON glasses studied by depth profiling at plasma etched surface using electron spectroscopy for chemical analysis. The plasma etching rate decreased with nitrogen content and there was no selective etching at the plasma etched surface of the oxynitride glasses. The concentration of silicon was very low due to the generation of SiF4 very volatile byproduct and the concentration of aluminum and yttrium was relatively constant. The elimination of silicon atoms during plasma etching was reduced with increasing nitrogen content because the content of the nitrogen was constant. And besides, the concentration of oxygen was very low on the plasma etched surface. From the study, the plasma etching resistance of the glasses may be improved by the generation of nitrogen related structural groups and those are proved by chemical composition analysis at plasma etched surface of the YSiAlON oxynitride glasses.

• 한국광물학회지
• /
• 제30권4호
• /
• pp.173-178
• /
• 2017

본 연구는 알루미나 기반의 기능성 세라믹 필터의 물리적 특성(강도와 기공률)에 대하여 소결온도와 영가철(ZVI) 함량의 영향을 파악하는 것이다. 기능성 세라믹 필터의 제조공정은 다양한 소결온도($1150^{\circ}C$, $1250^{\circ}C$)와 ZVI 함량(10, 20, 30, 50%)조건에서 수행하였다. 소결온도와 ZVI 함량의 증가됨에 따라 기능성 세라믹 필터의 강도는 증가하였지만 기공률은 감소하였다. 기능성 세라믹 필터의 강도와 기공률은 50%의 ZVI 함량과 $1250^{\circ}C$의 조건에서 각각 99.01 MPa과 34.5%로 나타났다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권3호
• /
• pp.50-61
• /
• 1995

In recent years, many ceramic researchers have discoved various methods of joining ceramic to metal. However, most of these joining methods are perfomed under vacuum and pressured circumstances. So, when we join ceramic to metal,the proceedings are very complicated and require a very high cost. The purpose of this study is to develop a new joining method of an alumina ceramic to an aluminum metal in air atmosphere. The joining condition, such as copper metallizing, nickel plating, brazing, etc. was investigated through the shear strength test of the trial joint. The results obtained from the above experimenta are summarized as follows : 1) In the case of the $Al_2O_3$/$Al_2O_3$joint, the shear strength of the joint was affected by the various foctor such as kaolin content, copper metallizing thickness, firing temperature, firing time. 2) The better shear strength of the $Al_2O_3$/Al joint was obtained when Ni plating was conducted under higher current density than existing plating condition. 3) The shear strength of the $Al_2O_3$/Al joint increases with the Ni plating thickness is confined to the range of this paper. 4) The shear strength of the thermal-shocked specimen($Al_2O_3$/Al joint) was far more deteriorated than that of the as-bonded specimen.