• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.74-82
• /
• 2017

This research presents the results of the strength and drying shrinkage properties to study the effect of ground granulated blast furnace slag(GGBFS), fly ash(FA) and calcium sulfoaluminate(CSA) for activated ternary blended slag cement. The activated ternary blended cement(ATBC) mortar were prepared having a constant water-cementitious materials ratios of 0.4. The GGBFS contents ratios of 100%, 80%, 70% and 60%, FA replacement ratios of 10%, 20%, 30% and 40%, CSA ratios of 0%, 10%, 20% and 30% were designed. The superplasticizer of polycarboxylate type were used. The activator was used of 10% sodium hydroxide(NaOH) + 10% sodium silicate($Na_2SiO_3$) by weight of binder. Test were conducted for mini slump, setting time, V-funnel, water absorption, compressive strength and drying shrinkage. According to the experimental results, the contents of superplasticizer, V-funnel and compressive strength increases with an increase in CSA contents for all mixtures. Moreover, the setting time, water absorption ratios and drying shrinkage ratio decrease with and increase in CSA. One of the major reason for the increase of strength and decrease of drying shrinkage is the accelerated reactivity of GGBFS with alkali activator and CSA. The CSA contents is the main parameter to explain the strength development and decreased drying shrinkage in the ATBC.

• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.324-329
• /
• 2005

The efficiency of reducing nitric oxide using urea combined with alkali salt additives is reported in this study. The inlet concentration of NO is 500 ppm with air flow rates of 3 and 5 L/min. Reduction of NO was studied from 650 to $1,050^{\circ}C$ with urea concentrations of 0.3 to 1 mol/L. The efficiency for the reduction of NO increased by 44% when urea is added alone. A further increase in efficiency was observed in the presence of NaOH as additive in fact, the efficiency was increased by more than 25% and 75% when 0.5 mol/L and 1 mol/L NaOH were added with the urea. The efficiency for the reduction of NO increased with all additives, but descended in the order NaOH, $Na_2CO_3$, $NaNO_3$, HCOONa, and CHCOONa. The maximum efficiency of NaOH and $Na_2NO_3$ are 74% and 73%, respectively. All these additives did not alter the comparatively wide operating temperature window for reducing NO. However, sodium compounds do not shift the maximum NO concentration towards lower temperatures when the NO removal activity enhances.

• Korean Journal of Food Science and Technology
• /
• v.19 no.5
• /
• pp.430-434
• /
• 1987

Fatty acid fraction rich in ${\omega}-3$ polyunsaturated fatty acids (${\omega}-3$, PUFA), especially eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) could be obtained by saponification of fish oil in ethanol containing alkali hydroxide followed by cooling and filtration of the resultant solution. Fatty acid compositions of fish oil and the concentrates suggest that the ratio of number of double bonds to carbon number in a fatty acid molecule is a more important factor than the degree of unsaturation or the chain length in determining the solubility of fatty acid salts in ethanol. Water content in ethano1 affected significantly the efficiency of the separation with respect to yield and content of EPA and DHA in the concentrates; the lower the water content, the higher the efficiency. It was, however, influenced little by cooling procedure and temperature which the saponified solution experienced during the crystallization. Under an optimal condition, the contents of EPA and DHA in the concentrate increased by 2.4 and 2.5 times, respectively, as compared with those in sardine oil.

• Journal of Sericultural and Entomological Science
• /
• v.35 no.1
• /
• pp.60-68
• /
• 1993

It has been known that the silk degumming treated by hot alkali solution is easy to handle but is liable to yield poor-quality silk due to the degree of degumming loss, incomplete-degumming or over-degumming. Therefore, many studies have been carried out on the silk degumming by enzyme in order to improve the quality of silk. However, no attention has been paid to the physicochemical analysis of enzymatic degummed silk. In this paper, two different degumming methods, soap and enzymatic, are compared in aqueous solution state of silk fibroin. The results can be summarized as follows: There was no significant difference between two solutions on the bases of polarizing microscopy, TEM observation and SDS-PAGE. Spherulite of silk fibroin was not observed in polarizing microscopy, however the leaf-shape fibril structure was developed upon solidification. The size of spherulites of silk fibroin in TEM observation were 30~120nm with a wide range of size distribution. The intrinsic viscosity of enzymatic degummed fibroin solution was lower than that of soap degummed solution. This can be explained that the silk fibroin was more degraded by enzymatic degumming method compared with the soap degumming method. SDS-polyacrylamide gel electrophoresis showed that the fibroin molecule was composed of large component of molecule weight above 50 kd and small component of molecule weight about 20 kd. There was no difference in crystallinity between two degumming methods on the bases of results of DSC thermograms and IR spectra.

• Resources Recycling
• /
• v.29 no.5
• /
• pp.28-37
• /
• 2020

In this study, the effect of precipitation temperature, ammonium chloride amount and addition method, vanadium and sodium hydroxide content of the solution on the precipitation of ammonium metavanadate were examined by using the sodium vanadate(NaVO₃) solution in alkali region as a starting material. As the pH of solution decreased, the addition amount of ammonium chloride and the vanadium content of the solution increased, the precipitation rate of ammonium metavanadate increased. In this research condition, the basic conditions for obtaining more than 90% of precipitation yield were 10,000mg/L of vanadium content, 2equivalents of ammonium chloride addition, room temperature, and 2 hours of precipitation time. The size of precipitated particles decreased with increasing precipitation rate. Especially when liquid ammonium chloride was injected into the solution, the precipitation rate was the slowest and the particle size of the precipitate was the largest. After the primary precipitation by adding ammonium chloride as a solid, the secondary precipitation was carried out by adding new reactants. At this time, the precipitation with added ammonium chloride solid was not affected by the precipitates present in the solution. However, when liquid ammonium chloride was added, new precipitate was deposited on the surface of the precipitate present in the solution, increasing its size. Due to the difference in ammonium metavanadate solubility to temperature, the precipitation temperature at the vanadium content of 10,000mg/L in the solution affected the precipitation rate of ammonium metavanadate and the precipitation temperature did not affect the precipitation rate at a high concentration of more than 30,000mg/L vanadium content in the solution.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.11
• /
• pp.1575-1581
• /
• 2011

Rapeseed cake, which is the organic waste remaining after rapeseed oil production, is readily available and considered an ecologically-friendly resource with very low cost and high dietary fiber content. This research was carried out for two reasons. First, it was done to analyze the liberated reducing sugar content of rapeseed cake. Second, it was done to investigate the effects on the sugar yield of the various concentrations of acidic and alkaline catalysts used for the hydrolysis of rapeseed cake and the concentrations of rapeseed cake in each catalyst. Several amounts of ground rapeseed cake, 0.5 g, 1 g, and 2 g, were put into 100 mL of catalysts such as sulfuric acid (0.5~2%), hydrochloric acid (0.5~2%), and sodium hydroxide (0.5~2%). Then they were hydrolyzed for 5 min at 121$^{\circ}C$. After hydrolysis, HPLC equipped with an RI detector was used to analyze liberated reducing sugars such as sucrose, glucose, galactose, fructose, and arabinose separated from rapeseed cake. The degradation rate of rapeseed cake was the highest in hydrochloric acid. As the catalyst concentrations used for hydrolysis of rapeseed cake increased, the degradation rate of rapeseed cake also significantly increased. Total reducing sugar content was the highest in hydrochloric acid, and it increased with the increase of catalyst concentrations. However, as the amount of rapeseed cake increased, the total reducing sugar content decreased, exceptionally sucrose in the case of sodium hydroxide.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.1
• /
• pp.3-10
• /
• 1984

Taro-UF mixed type resin system was developed for gluing plywoods. The taro adhesive that was activated with sodium hydroxide was mixed with the definite ratios of UF resin adhesive. At the sametime, wheat-UF mixed type resin was also applied with the same method as taro-UF mixed type resin The mixing ratios of taro or wheat adhesive: UF resin were 0:100, 10:90, 20:80, 30:70, 40:60, 50:50, 60:40, 80:20, and 100:0 by weight. In addition, the UF resins extended with wheat powder at the extending ratios of wheat powder UF resin, 10:90, 20:80, 30:70, 40:60, and 50:50 by weight, were also used. The dry and wet shear strengths of the plywoods of 30:70 (taro adhesive : UF resin) mixing ratio were highest. The dry shear strengths of the plywoods manufactured with the UF resin-mixing taro adhesive were higher than those of the plywoods with the UF resin-mixing wheat adhesive at 10:90, 20:80, 30:70, 40:60, 50:50, and 60:40 (taro or wheat adhesive: UF resin) mixing ratios. At all mixing ratios, the wet shear strengths of the plywoods manufactured with the UF resin-mixing taro adhesive were higher than those of the plywoods with the UF resin-mixing wheat adhesive. The dry and wet shear strengths of the plywoods manufactured with the UF resin-mixing wheat adhesive were higher than those of the plywoods with the wheat powder-extending UF resin at the mixmg ratios, 10:90, 20:80, 30:70, and 40:60 (wheat adhesive or wheat powder: UF resin). So, it was found that the plywoods manufactured with the UF resin-mixing taro adhesive and the UF resin mixing wheat adhesive had better shear strength than the plywoods with the wheat powder-extending UF resin. It was because the taro adhesive and wheat adhesive themselves took the bonding properties after being activated with alkali.

• Clean Technology
• /
• v.28 no.1
• /
• pp.46-53
• /
• 2022

The agglomeration characteristics of coal and silica sand were investigated under various conditions using mixed samples consisting of coal, silica sand, and potassium hydroxide, which is an agglomeration accelerator. The samples were prepared by either physically mixing or using aqueous solutions. The experiments using the physically mixed powder samples were performed with a two hour reaction time. The results showed that the number of aggregates generated increased as the reaction temperature and the total potassium content increased. The experiments using aqueous solutions were performed at 880 ℃, which is the operating temperature of a fluidized bed boiler, and at 980 ℃, which assumes a local hot spot. The amount of agglomeration generated as the reaction time increased and the total potassium content increased was identified. In the experiment performed at 880 ℃, the amount of aggregate generated clearly increased with the reaction time, and in the experiment performed at 980 ℃, assuming a local hot spot, a large amount of aggregate was generated in a relatively short time. The aggregates became harder as the potassium content increased. When the total potassium content was less than 1.37 wt.%, the aggregates were weak at both temperatures and collapsed even with a slight impact. Additionally, the surface characteristics of the silica sand and ash aggregates were observed by SEM-EDS analysis. The analysis revealed a large amount of potassium at the bonding sites. This result indicates that there is a high possibility of aggregation in the form of a eutectic compound when the alkali component is increased.