• 한국전기전자재료학회논문지
• /
• 제32권5호
• /
• pp.357-360
• /
• 2019

We demonstrate an alignment technology using an imprinting process on an inorganic NiOx film. The aligned nanopattern was fabricated on a silicon wafer by laser interference lithography. The aligned nano pattern was then imprinted onto the sol-gel driven NiOx film using an imprinting process at an annealing temperature of $150^{\circ}C$. After the imprinting process, parallel grooves had been formed on the NiOx film. Atomic force microscopy and water contact angle measurements were performed to confirm the parallel groove on the NiOx film. The grooves caused liquid crystal alignment through geometric restriction, similar to grooves formed by the rubbing process on polyimide. The liquid crystal cell exhibited a pretilt angle of $0.2^{\circ}$, which demonstrated homogeneous alignment.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.1043-1046
• /
• 2000

By combination of X-ray lithography, electroplating and molding process, various microstructures have been produced. Specially, the alignment grooves for multi-fibers with submicron accuracy have been produced. This paper described a fabrication process of LICA molds and micro molding technique by using LIGA molds. The accuracy of the fabricated LIGA molds was less than 0.4${\mu}{\textrm}{m}$. The injection molded alignment grooves were very precise and had me surface roughness so that they could be successfully applicable to optical systems.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.594-598
• /
• 2019

HfZnO 박막 위 패턴 전사 기법을 이용하여 기존의 러빙법을 대체하는 배향 공정에 대하여 연구하였다. 정렬 패턴은 레이저 간섭 리소그래피를 이용하여 실리콘 웨이퍼 위에 제작하였다. 졸겔 공정을 이용하여 HfZnO 용액을 제작하였고, 유리기판 위에 스핀코팅하였다. 미리 제작한 정렬패턴을 스핀코팅된 HfZnO 위에 올려놓고, $100^{\circ}C$에서 30분간 소성하였다. HfZnO 박막에 평행한 그루브가 형성되었음을 atomic force microscopy 와 scanning electron microscopy로부터 확인할 수 있었다. HfZnO 박막을 이용하여 액정 셀을 제작하였으며, POM 분석으로부터 액정이 균일하게 정렬되었음을 확인할 수 있었다. 액정은 $0.25^{\circ}$의 프리틸트 각을 가졌으며, 수평배향 특성을 보여주었다. 액정 분자는 평행한 그루브에 의한 HfZnO 박막 표면 이방성에 의하여 균일하게 정렬되었음을 확인할 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• 제7권6호
• /
• pp.305-308
• /
• 2006

We have studied liquid crystal (LC) aligning capabilities for homeotropic alignment and the control of tilt angles on the $SiO_{x}$ thin film by electron beam evaporation method. A high tilt angle of about $86.5^{\circ}$ was obtained, and also the suitable tilt angle of the NLC on the $SiO_{x}$ thin film at $20{\sim}50\;nm$ thickness with e-beam evaporation can be achieved. The uniform LC alignment on the $SiO_{x}$ thin film surfaces with electron beam evaporation can be achieved. It is considerated that the LC alignment on the $SiO_{x}$ thin film by electron beam evaporation is attributed to elastic interaction between LC molecules and micro-grooves at the $SiO_{x}$ thin film surface created by evaporation.

• 한국전기전자재료학회논문지
• /
• 제16권12호
• /
• pp.1110-1114
• /
• 2003

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using thin plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The NLC pretilt angles generated are about 3$^{\circ}$ by the rubbing alignment method on thin plastic substrates, However, the pretilt angle are at about 1.7$^{\circ}$ lower on the glass substrate than on thin plastic substrate. We obtain that AFM (atomic force microscope) image of rubbed PI surface with polymer film has formed the micro-groove structure at the low curring temperature (120$^{\circ}C$). However, no grooves are obtained on the glass substrate at the same temperature. It is considered that this alignment may be attributed to roughness of micro-groove substrate. The tilt angle increases with increasing baking temperature for making polyimide layer using glass substrate. It was concluded that the pretilt angle in the polyimide surface is attributable to the increasing of imidization rato.

• ETRI Journal
• /
• 제27권4호
• /
• pp.446-448
• /
• 2005

Using tightly focused femtosecond laser pulses, we produce an optical waveguide and devices in transparent materials. This technique has the potential to generate not only channel waveguides, but also three-dimensional optical devices. In this paper, an optical splitter and U-grooves, which are used for fiber alignment, are simultaneously fabricated in a fused silica glass using near-IR femtosecond laser pulses. The fiber- aligned optical splitter has a low insertion loss, less than 4 dB, including an intrinsic splitting loss of 3 dB and excess loss due to the passive alignment of a single-mode fiber. Finally, we present an output field pattern, demonstrating that the splitting ratio of the optical splitter becomes approximately 1:1.

• Transactions on Electrical and Electronic Materials
• /
• 제8권6호
• /
• pp.274-277
• /
• 2007

In this study, liquid crystal(LC) aligning capabilities for homeotropic alignment on the $SiO_x$ thin film by electron beam evaporation method were investigated. Also, the control of pretilt angles and thermal stabilities of the nematic liquid crystal(NLC) treated on $SiO_x$ thin film were investigated. A high pretilt angle of about $86.5^{\circ}$ was obtained, and also the suitable pretilt angle of the NLC on the $SiO_x$ thin film at $10{\sim}50nm$ thickness with e-beam evaporation can be achieved. The uniform LC alignment and good thermal stabilities on the $SiO_x$ thin film surfaces with electron beam evaporation can be achieved. It is considered that the LC alignment on the $SiO_x$ thin film by electron beam evaporation is attributed to elastic interaction between LC molecules and micro-grooves at the $SiO_x$ thin film surface created by evaporation.

• 천문학논총
• /
• 제19권1호
• /
• pp.47-54
• /
• 2004

We present the detailed description on the fiber techniques adopted in the BOES: the design concepts and manufacturing of the v grooves, the procedures of the fiber polishing, adhering of the fibers to the v grooves, and the axis alignment of the fiber input and exit. The high efficiency and throughput of the BOES imply that the adopted fiber arts and the other optical components were well designed and properly treated. We learned that the relatively low efficiency of the 80 micron fiber comparing with the 200 and 300 micron fibers comes from the seeing and the guiding effects not from the poor fiber handling.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.439-441
• /
• 1996

A simple coupling method between APD(avalanche photodiode) arrays and SMF(single mode fiber) arrays on a Silicon carrier composed of V-grooves is proposed and carried out. Jacketed fibers embedded in V-grooves are used as alignment marks instead of patterned pedestals or solder bumps and a optical receiver module are packaged.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.378-378
• /
• 2007

In this study, liquid crystal (LC) aligning capabilities for homeotropic alignment on the $ZrO_x$ thin film by electron beam evaporation method were investigated. Also, the control of pretilt angles and thermal stabilities of the NLC treated on $ZrO_x$ thin film were investigated. The uniform LC alignment on the $ZrO_x$ thin film surfaces and good thermal stabilities with electron beam evaporation can be achieved. It is considerated that the LC alignment on the $ZrO_x$ thin film by electron beam evaporation is attributed to elastic interaction between LC molecules and micro-grooves at the $ZrO_x$ thin film surface created by evaporation. In addition, it can be achieved the good electro-optical (EO) properties of the VA-LCD on $ZrO_x$ thin film layer with. oblique electron beam evaporation.