• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.374-377
• /
• 2008

The prediction of the separation trajectories of the external stores released from a military aircraft is an important task in the aircraft design area having the objective to define the operational and release envelopes. This paper presents the results obtained for store separation by employing commercial sorftwares, FLUENT and CFD-FASTRAN. FLUENT treats the rigid body motion by employing the remeshing scheme. CFD-FASTRAN uses the chimera(overset) grid and interpolations. It was found that, for the prediction of the trajectories and behavior of the stores separated from the wing, both codes shows the good agreement with the experimental results.

• Structural Engineering and Mechanics
• /
• v.61 no.4
• /
• pp.441-451
• /
• 2017

The need of progress in engineering designs especially for aerospace structure is nowadays becoming a major industry request. The objectives of this work are to quantify the influence of material and operational uncertainties on the performance of the aerodynamic behavior of an Aircraft Wing, and to give a description of the most commonly used methods for reliability based design optimization (RBDO) to point out the advantages of the application of this method in the design process. A new method is proposed, called Safest Point (SP) that can efficiently give the reliability-based optimum solution for freely vibrating structures with and without fluid flow.

• International Journal of Aeronautical and Space Sciences
• /
• v.2 no.1
• /
• pp.93-102
• /
• 2001

Flight control design for the autonomous waypoint navigation of aircraft is presented in this study. The waypoints are defined in terms of desired longitude and latitude. The control design is conducted in longitudinal and lateral directions, respectively. The lateral control is based upon coordinated turn strategy for which no sideslip is allowed under the turning maneuver. The longitudinal control is mainly focused on altitude hold during navigation. Neural network control approach is applied to the altitude-hold mode control. Simulation of the proposed control strategy has been performed under various conditions. A graphical simulation tool was developed to visually demonstrate the control technique developed in this study. A method to simulate the gas turbine transient behavior is developed. The basic principles of the method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.191-195
• /
• 2011

The airframe ground vibration tests were conducted on the KC-100 aircraft according to the regulation requirement, KAS 23.629(a)(2) and the modal characteristics for the target modes were measured. To make FE model tuning, a design sensitivity approach with engineering judgment was implemented using MSC/Nastran and Attune, a genetic algorithm based parameter optimization software. Based on the comparison between initial prediction and test results, design variables such as beam cross-sectional properties and spring stiffnesses were devised. As the results, the correlation of the FE model to the GVT results was made appropriately, meeting the goal of matching the target frequencies within 5%.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.8 no.1
• /
• pp.83-95
• /
• 2000

Lift, drag, pitching moment, what we call longitudinal aerodynamic coefficient, effects airplanes directly, so the method to find the accurate result quickly is an important factor from the beginning of the aircraft design. There are different ways to find aerodynamic coefficient such as empirical methods, numerical analysis methods, wind tunnel tests, and finally through an actual flight tests, but choosing the best methods depends on the due date or the cost. The accuracy varies on each design level, but all this methods have relationship to complement and balance each other, so by combining proper methods, the best result can be obtained. At this paper, empirical methods and numerical analysis method were experimented, compared, and reviewed to find the availability of each method and by combining two methods accurate result was obtained. So, we applied this methods to predict the aerodynamic coefficient on cruise configuration aircraft, and was able to obtain more accurate result on the low speed longitudinal aerodynamic coefficient. Also by watching there result, we are able to predict the errors before the actual wind tunnel test.

• Journal of Aerospace System Engineering
• /
• v.7 no.2
• /
• pp.47-54
• /
• 2013

This paper describes and analyzes the HIRF protection standards of the helicopter category focused on external RF environments. In addition, this paper presents an ideal process of airplane design to accomplish the successful certification. Furthermore, this paper proposes practical recommendations to reduce RF energy on aircraft using specific EMI/EMC techniques such as shielding, grounding and filtering methods. Most of the proposed methods in this paper were key issues during the certification process of KC-100 small airplane which is Korea's first trial aircraft for civil airplane certification.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.514-519
• /
• 2003

The aircraft engine is usually supported by rolling element bearings and has a small damping rate, which is vol y sensitive to external force. The high-performance requirement of the rotors leads to complex assembly designs and are more flexible. Squeeze film dampers (SFDs) are introduced to provide damping while crossing the critical speeds and stability to the rotor s :stem. Hence, the focus of the present investigation is on the decision of an optimal size of the flexible rotor system supported by the squeeze film dampers to minimize the maximum transmitted load and unbalance response over a range operating speeds. The enhanced genetic algorithm (EGA), which was developed by authors, is used in the optimization process. This algorithm is based on the synthesis of a modified genetic algorithm and simplex method. The results show significant benefits in using EGA when compared with nonlinear programming (NLP).

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.75-78
• /
• 2004

Traditionally aluminum alloy have been used in manufacturing of aircraft structures, and semi-monocoque structural concept have been mainly applied in structural design of fuselage and wing. However, recently monocoque structural concept is applied in many small-size aircraft structures manufactured with composite materials. In such case appling monocoque structural concept, in initial conceptual design stage on wing, it is not easy to analyze shear flow using classical shear flow analytical method because composite skin structure can support span-wise tension/compression stress as well as sectional shear stress. In this study, an extended shear-flow analytical method to apply to composite monocoque structural concept was developed through extending the classical shear-flow analytical method.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.110-116
• /
• 2005

A single-piece-machined-part has superior characteristics to an assembly of several pieces of part especially for aircraft components. It is necessary to develop high efficient 'multi-head router machine' for machining a large size single-piece-part on a large scale. In this type machine, many cutting chips are generated. These chips should be removed automatically f3r productivity and part precision. In this study, the design evaluation of the cutting chip collecting apparatus for 'multi-head router machine' was complemented using performance test and finite element analysis.

• Journal of Advanced Navigation Technology
• /
• v.17 no.6
• /
• pp.664-671
• /
• 2013

In this paper, in an aircraft power can be measured by wireless AEMS (aircraft electric power measurement monitoring system) system is proposed. AEMS has been design based on current commercialized power measuring systems analysis with improvement and connects it with most talked about item, smart phone and monitoring system. And also adopting real time power measuring system, constitute more practical power measuring system by controlling electricity usage in real time.