• Journal of Mechanical Science and Technology
• /
• v.16 no.9
• /
• pp.1065-1071
• /
• 2002

The friction and wear behaviors of magnetron sputtered MoS$_2$ films were investigated through the use of a pin and disk type tester. The experiments were performed for two kinds of specimens (ground (Ra 0.5 $\mu\textrm{m}$) and polished (Ra 0.01 $\mu\textrm{m}$) substrates) under the following operating condifions : linear sliding velocities in the range of 22～66 mm/s (3 types), normal loads varying from 9.8～29.4 N(3 types) and atmospheric conditions of air, medium and high vacuum (3types). Silicon nitride pin was used as the lower specimen and magnetron sputtered MoS$_2$ on bearing steel disk was used as the upper specimen. The results showed that low friction property of the MoS$_2$ films could be identified in high vacuum and the specific wear rate in air was much higher than that in medium and high vacuum due to severe oxidation. It was found that the main wear mechanism in air was oxidation whereas in high vacuum accumulation of plastic flow and adhesion, were the main causes of wear.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.2
• /
• pp.61-69
• /
• 2012

Alloys of Fe-(5, 10, 15)Al and Fe-(10, 20, 30, 40)Cr were corroded at 700 and $800^{\circ}C$ for 70 hr in either atmospheric air or 1 atm of Ar+$1%SO_2$ gases. In these atmospheres, Fe-5Al and Fe-10Cr alloys displayed poor corrosion resistance. In atmospheric air, Fe-5Al alloys formed oxide nodules, while Fe-10Cr alloys formed thick scales and internal oxides. In Ar+$1%SO_2$ gases, Fe-5Al and Fe-10Cr alloys formed thick, nonadherent bi-layered scales, which grew primarily by the outward diffusion of Fe ions and inward diffusion of oxygen and sulfur ions. By contrast, in atmospheric air and Ar+$1%SO_2$ gases, Fe-(10, 15)Al and Fe-(20, 30, 40)Cr alloys displayed good corrosion resistance by forming $Al_2O_3$ and $Cr_2O_3$ layers on the surface, respectively.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.237-245
• /
• 2018

Potential air ingress scenarios during accidents in nuclear reactors or spent fuel pools have raised the question of the influence of air, especially of nitrogen, on the oxidation of zirconium alloys, which are used as fuel cladding tubes and other structure materials. In this context, the reaction of zirconium with nitrogen-containing atmospheres and the formation of zirconium nitride play an important role in understanding the oxidation mechanism. This article presents the results of analysis of the interaction of the oxygen-preloaded niobium-bearing alloy $M5^{(R)}$ with nitrogen over a wide range of temperatures ($800-1400^{\circ}C$) and oxygen contents in the metal alloy (1-7 wt.%). A strongly increasing nitriding rate with rising oxygen content in the metal was found. The highest reaction rates were measured for the saturated ${\alpha}-Zr(O)$, as it exists at the metal-oxide interface, at $1300^{\circ}C$. The temperature maximum of the reaction rate was approximately 100 K higher than for Zircaloy-4, already investigated in a previous study. The article presents results of thermogravimetric experiments as well as posttest examinations by optical microscopy, scanning electron microscopy (SEM), and microprobe elemental analyses. Furthermore, a comparison with results obtained with Zircaloy-4 will be made.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.10 no.1
• /
• pp.47-55
• /
• 1990

This paper presents experimental results which explore the capability of a CW laser speckle photography for tile measurement of in-plane displacement at high temperature. The serious restrictions on the application of the method seem to be the ambient air turbulence and the change of surface texture caused by the oxidation, as they tend to decorrelate the double exposured speckle patterns. In order to assess only the effect of air turbulence, a ceramics-coated stainless steel plate is heated in air and Ar-laser specklegrams are made with combination of temperature and lateral translation displacement. The slight reduction in visibility of Young's fringes is observed at $1000^{\circ}C$. The analyses of Young's fringes are carried out by a image processing system using a TV-camera and computers, and the result agrees well with the micrometer reading. Futhermore, uncoated stainless steel and Hastelloy X plates are tested and the effect of oxidation is also evaluated. The experimental results demonstrate that a CW laser speckle photography is applicable at temperatures up to $1000^{\circ}C$.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.237-244
• /
• 2000

Phenolic resin used as a precursor of carbonized matrix for carbon-carbon composites was modified by addition of molybdenum disilicide (MoSi$_2$) in various concentrations of 0, 4, 12 and 20% by weight to improve the anti-oxidation properties of the composites. The green body was manufactured by a prepreg method and was submitted to carbonization up to 110$0^{\circ}C$. In this work, the oxidation behavior of carbon-carbon composites with MoSi$_2$ as an oxidation inhibitor was investigated at the temperature range of 600-100$0^{\circ}C$ in an air environment. The carbon-carbon composites with MoSi$_2$ showed a significantly improved oxidation resistance due to both the reduction of the porosity formation and the formation of mobile diffusion barrier for oxygen when compared to those without MoSi$_2$. Carbon active sites should be blocked, decreasing the oxidation rate of carbon. This is probably due to the effect of the inherent MoSi$_2$ properties, resulted from a formation of the protective layer against oxygen attack in the composites studied.

• Journal of the Korean Ceramic Society
• /
• v.36 no.5
• /
• pp.555-563
• /
• 1999

Impregnation of phosphorous additiers into graphite bulk was studied with the goal of enhancing the effectiveness of oxidationprotection. In addition graphite acid washing was carried out prior to the impregnation further to improve oxidation resistance. Observation of the oxidation rate for raw graphite(Raw) impregnated graphite with tri-butyl phsophate on raw block(RP) and impregnated graphite on acid-treated graphite(AP) in air are reported. The phsophorus residue adsorbed on the graphite surface at active sites was determined by FTIR, XRS, TGA techniques. AP with tri-butyl phosphate was found to result in both 30% reduction in oxidation rate at 1000$^{\circ}C$ compared to Raw and increase of 120$^{\circ}C$ in oxidation temperature From the samples of oxidation rate of each specimen in Arrhenius plot it can be said that the present oxidation resistance origninates from the change of chemical reaction modesw neigther by acid-washing treatment nor phsophate impregnation

• Journal of Korean Society for Atmospheric Environment
• /
• v.27 no.5
• /
• pp.534-544
• /
• 2011

The secondary aerosol forming potential of ambient air was first measured with the Potential Aerosol Mass(PAM) chamber at Gosan supersite on Jeju island from October 22 to November 5, 2010. PAM chamber is a small flowthrough photo-oxidation chamber with extremely high OH and $O_3$ levels. The OH exposure in the PAM chamber was $(2{\pm}0.4){\times}10^{11}{\sim}(6{\pm}1.2){\times}10^{11}$ molecules $cm^{-3}$ s and was similar to 2 to 5 days of aging in the atmosphere. By periodically turning on and off UV lamps in the PAM chamber, ambient aerosol and newly formed aerosol (e.g. called as PAM aerosol) was alternately measured. Aerosol number and mass concentration in the range of 10~487 nm in diameter was measured by SMPS 3034. With UV lamps on, the nucleation mode particles smaller than 50 nm in diameters were formed. Their number concentration was greater than 105 $cm^{-3}$, leading to increase in aerosol mass by 0~8 ${\mu}gm^{-3}$. The variations of PAM and ambient aerosols were greatly dependent on characteristics of air masses such as precursor concentrations and degree of aging. This preliminary results suggests that PAM chamber is useful to assess the aerosol formation potential of air mass and its impact on the air quality. The further analysis of data with gaseous and particulate measurements will be done.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.20 no.3
• /
• pp.214-219
• /
• 1991

The damaging effect of peroxidized lipid on amino acid was studied in rice bran by determining the free amino acid content in abiological system. The content of free amino acid in the rice bran stored in the controlled atomsphere of $35^{\circ}C$ with relative humidity of 65% for 180 days, increased during the first 60 days of storage, and then decreased as the lipid peroxidation proceeded. The content of free amino acid in the sample exposed to the air of $25-30^{\circ}C$ with relative humidity of 70-90% for 100 days decreased rapidly in the beginning period of the storage. The lipid oxidation developed much faster in the rice bran exposed to the air than in the rice bran stored in the controlled atmosphere. The correlation coefficients between the total content of free amino acid and degree of peroxidation for the samples of both conditions were above -0.8, which is significant(p<0.05). The changes in the concentration of serine, glutamic acid, proline, methionine, lysine, histidine, and arginine were significantly correlated with the degree of lipid oxidation(p<0.05) for the samples stored in the controlled atmosphere and the open air. It was observed that peroxidized lipid has damaging effects on protein in the bilogical system of rice bran.

• Korean Journal of Chemical Engineering
• /
• v.35 no.12
• /
• pp.2403-2412
• /
• 2018

The present study was aimed at evaluating the effect of variable sodium carbonate ($Na_2CO_3$) loading during wet air oxidation (WAO) pretreatment of rice straw in reducing biomass recalcitrance. The research study was intended to increase the cellulose recovery, hemicellulose solubilization, lignin removal in the solid fraction and limiting the generation of inhibitors in the liquid fraction while reducing the chemical input. The operating condition of $169^{\circ}C$, 4 bar, 18 min and 6.5 g/L $Na_2CO_3$ loading resulted in maximum cellulose recovery of 82.07% and hemicellulose solubilization and lignin removal of 85.43% and 65.42%, respectively, with a total phenolic content of 0.36 g/L in the liquid fraction. The crystallinity index increased from 47.69 to 51.25 along with enzymatic digestibility with an increase in $Na_2CO_3$ loading from 0 to 6.5 g/L as a result of removal of barriers for saccharification via effective cleavage of ether and ester bonds cross-linking the carbohydrates and lignin as indicated by FT-IR spectroscopy. A further increase in the $Na_2CO_3$ loading to 9.5 g/L did not significantly increase the sugar release. Thus, it was concluded that 6.5 g/L $Na_2CO_3$ during WAO is sufficient to increase the delignification and deacetylation, leading to significant changes in apparent cellulose crystallinity inter alia improvement in cellulose accessibility and digestibility of rice straw.

• Carbon letters
• /
• v.5 no.4
• /
• pp.164-169
• /
• 2004

Carbon-ceramic composites refer to a special class of carbon based materials which cover the main drawbacks of carbon, particularly its proneness to air oxidation, while essentially retaining its outstanding properties. In the present paper, the authors report the results of a systematic study made towards the development of C-SiC-$B_4C$ composites, which involves the effects of compositional parameters, namely, carbon-to-ceramic and ceramic-to-ceramic ratios, on the oxidation behaviour as well as other characteristics of these composites. The C-SiC-$B_4C$ composites, heat-treated to $1400^{\circ}C$, have shown that their oxidation behaviour at temperatures of 800~$1200^{\circ}C$ depends jointly on the total ceramic content and the SiC : $B_4C$ ratio. Good compositions of C-SiC-$B_4C$ composites exhibiting zero weight loss in air at temperatures of 800~$1200^{\circ}C$ for periods of 4~9 h, have been identified. Composites with these compositions undergo a weight gain or a maximum weight loss of less than 3% during the establishment of a protective layer at the surface of carbon in a period of 1~6 h. Significant improvement in the strength of C-SiC-$B_4C$ composites has been observed which increases with an increase in the total ceramic content and also with an increase in the SiC : $B_4C$ ratio.