• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1905-1907
• /
• 1997

The experiments of laser-guided de discharge were carried out by using pulsed Nd:YAG laser radiation at low air pressure ranging from 0.3 to 20 torr. The minimum laser-guided de discharge voltages($V_{MD}$) at given pressure and distances between anode and cathode electrode were obtained. In order to generate TEM(transverse electromagnetic waves) modes, a pinhole was installed between a rod and a half mirror, and its diameter was adjusted from 6mm to 1.7mm. And then, we investigated the characteristics of laser-guided de discharge corresponding to different TEM modes. As a result, it was found that $V_{MD}$ at $TEM_{00}$ mode was lower than $V_{MD}$ at multimodes.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.184-193
• /
• 2003

Cyclic sweep voltametry was performed to investigate the electrochemical behavior of heavy metal ions and the organic additives in surface finishing process. And electrolysis using parallel plate electrode electrolyzer was carried out to simulate the treatment of real waste water. Results showed that more than 99 percent of Cu was recovered and selective recovery of Cu in mixed waste water was possible, but the possibility of economical recovery of Ni and Cr were very low due to the evolution of hydrogen gas. Electrochemical oxidation of cyanide and organic additives on anode showed very excellent removal rate. The complete removal of several hundred ppm of cynide was possible within several tens minutes and organics within 2 or 3 hours. Even in case of concentrate waste water, the complete removal of COD by using NaCl and air stirring seemed to be possible.

• 기술사
• /
• 제44권1호
• /
• pp.48-52
• /
• 2011

The KEPCO Research Institute has developed Molten Carbonate Fuel Cell(MCFC) since 1993. Recently, an 125-kW MCFC system was operated at Boryeong thermal power plant, Korea from December, 2009 to March, 2010, This system is composed of an 125-kW stack, mechanical balance of plant (MBOP), and Power Conditioning System. The stack has 200 unit cells of which effective area is 10,000 cm2. Especially, MBOP is mainly made up of ejector and catalytic combustor which help this system to be supplied with cathode inlet gas using anode tail gas and fresh air. After the pretreatment of this system was performed for about 20 days, initial load operation was performed at January. 2010. Moreover, this system had been operated for 3,270 hours.

• 한국결정성장학회지
• /
• 제10권1호
• /
• pp.55-61
• /
• 2000

리튬이온전지의 음극재료로서 hard carbon에 PVC를 이용한 탄소를 코팅함으로써 비가역용량 감소와 가역용량 증가 등 전기화학적 특성이 향상되었다. 이러한 특성 향상은 PVC코팅에 의한 표면개질로 대기와의 반응을 억제함에 기인한 것으로 생각되며, 또한 Ni 첨가에 의해 PVC 탄소의 흑연화 정도를 조절할 수 있었으며, 이들과 관련된 전기화학적 특성을 비교 고찰하였다.

• 한국분말재료학회지
• /
• 제17권1호
• /
• pp.59-64
• /
• 2010

8 mol% Y-doped $SrTiO_3$ powder was synthesized by Pechini method from titanium isopropoxide, strontium nitrate, yttrium nitrate, citric acid and ethylene glycol. A $Y_2Ti_2O_7$ pyrochlore phase-free perovskite powder was obtained by calcining a polymeric resin, which was prepared from a precursor solution, at $500^{\circ}C$ in an air atmosphere. Low temperature calcination could lead to a fine-grained microstructure. In the case of a solid-state reaction, an extended heat-treatment at high temperature in a reduced atmosphere needed to obtain a single phase perovskite $SrTiO_3$.

• Bulletin of the Korean Chemical Society
• /
• 제18권1호
• /
• pp.61-65
• /
• 1997

The electrochemical properties of LixCoyNi1-yO2 compounds (y=0.1, 0.3, 0.5, 0.7, 1.0) prepared by citrate sol-gel method have been investigated. The LixCoyNi1-yO2 compounds were annealed at 850 ℃ for 20 h after preheating at 650 ℃ for 6 h, in air. The x-ray diffraction (XRD) patterns for LixCoyNi1-yO2 have shown that these compounds have a well developed layered structure (R&bar{3} m). From the scanning electron microscopy of LixCoyNi1-yO2, particle size was estimated less than 5 μm. The Li//LixCoyNi1-yO2 electrochemical cell consists of Li metal anode and 1 M LiClO4-propylene carbonate (PC) solution as the electrolyte. The differences in intercalation rate of the LixCoyNi1-yO2 in the first charge/discharge cycle were less than 0.05 e-. The first discharge capacities of LixCoO2 and LixCo0.3Ni0.7O2 were ∼130 mAh/g and ∼160 mAh/g, respectively.

• 한국수소및신에너지학회논문집
• /
• 제32권5호
• /
• pp.410-416
• /
• 2021

The initial electrochemical performance of ceramic fuel cell with thin-film electrolyte was evaluated in terms of peak power density ratio, open circuit voltage ratio, and activation/ohmic resistance ratios at 500℃. Hydrogen and air were used as anode fuel and cathode fuel, respectively. The peak power density ratio reduced as ~17% for 40 minutes, which rapidly decreased in the early stage of the performance evaluation but gradually decreased. The open circuit voltage ratio decreased with respect time; however, its time behavior was remarkably different with the reduction behavior of the peak power density ratio. The activation resistance ratio increased as ~15% for 40 minutes, which was almost similar with the time behavior of the peak power density ratio.

• 한국수소및신에너지학회논문집
• /
• 제32권5호
• /
• pp.340-346
• /
• 2021

The initial electrochemical performance of ceramic fuel cell with thin-film electrolyte fabricated by plasma-enhanced atomic layer deposition method was evaluated in terms of peak power density ratio, open circuit voltage ratio, and activation/ohmic resistance ratios at 500℃. Hydrogen and air were used as anode fuel and cathode fuel, respectively. The peak power density ratio reduced as ~52% for 30 min, which continually decreased as time increased but degradation rate gradually decreased. The open circuit voltage ratio decreased with respect time; however, its behavior was evidently different from the reduction behavior of the peak power density. The activation resistance ratio increased as ~127% for 30 min, which was almost similar with the reduction behavior of the peak power density ratio.

• 대한기계학회논문집B
• /
• 제34권6호
• /
• pp.643-648
• /
• 2010

출구부가 폐쇄된 데드앤드 모드 운전은 연료이용률이 높고, 부가장치 소모동력이 작기 때문에 소형연료전지 분야에 널리 적용되고 있다. 하지만 수증기나 질소 등과 같은 불순물의 축적으로 인해 성능이 저하되는 단점을 가지고 있다. 본 논문에서는 이러한 성능 저하의 요인 중 수분 축적의 영향을 알아보기 위해 부하 방식에 따른 거동, 퍼징 전후 분극 성능, 수분 축적 분포, 공기극 상대습도에 따른 성능을 알아보았다. 본 실험에 적용된 운전 조건에서의 성능 거동은 정전압 부하(0.4V)보다 정전류밀도 ($600mA/cm^2$)부하에서 보다 안정적으로 나타났다. 가시화 창을 통해 수소극에 축적된 대부분의 수분은 출구부에 가까운 부분에 분포함을 알 수 있었다. 또한 공기극 상대습도(0.15, 0.4, 0.75 RH)가 높아질수록 성능 유지 시간은 감소한 반면 성능 감소율은 증가하였다. 특히, 상대습도 0.15에서의 성능 기준으로 평균출력밀도는 51% 증가하였고, 평균성능유지시간은 25% 감소하였다.

• 전기화학회지
• /
• 제2권2호
• /
• pp.81-87
• /
• 1999

Polyacrylonitrile(PAN)섬유를 원료로 여러 가지 조건하에서 탄소섬유를 제조하여 리튬이온 이차전지 음극 활물질로 사용하여, 전지의 충$\cdot$방전 특성과 전기화학적 특성을 고찰하였다. 음극활물질 제조에 있어서 고려한 주요한 변수들은 탄화 열처리 온도(HTT : heat treatment temperature), 탄화시의 가스분위기와 안정화(stabilization)시 섬유 축방향으로 가해주는 장력이며, 제조된 탄소섬유의 물성 및 전기적 특성 역시 조사하였다. 본 연구에서 사용한 열처리 온도 범위는 $700^{\circ}C\~1500^{\circ}C$로서, 처리온도가 상승 할 수록 전도성은 비례하여 향상되었으나, 900"C 범위는 아직 낮은 전도성을 보였다. 또한 처리온도 증가에 따라 충 방전효율은 증가하는 반면, 충 방전용량은 감소되는 경향을 보였다. 그리고 탄화시의 가스 분위기에 따라서 제조되는 음극활물질의 전지특성에 영향을 받았다. 특히, 다른 가스 분위기 하에서 제조된 PAN계 전극들의 측정된 리튬이온의 확산계수 값은 전지의 충$\cdot$방전 특성과 일치하는 결과를 보였다. 탄화시 서로 다른 가스분위기에서 탄소섬유 표면상에 형성된 다양한 기능기그룹(surface functional group)들이 리튬이온과의 비가역적 반응이 진행되는 사실을 간접적으로 확인하게 해준다. 산화분위기에서의 안정화시의 PAN섬유에 가해지는 장력은 가교 결합 중에 형성되는 분자의 배향을 유지시켜 주는 역할을 하는데, 안정화처리 후에도 섬유의 길이변화가 없는 장력조건 (fixed-length condition)에서 충 방전효율 및 용량과 사이클 안정성이 우수한 것으로 나타났다.