• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.3
• /
• pp.90-95
• /
• 1999

The durability of handmade paper prepared by potassium carbonate cooking of paper multiberry (Broussonetia Kazinoki Sieb).was investigated. The potassium carbonate paper before and after heat aging had better strength properties, breaking length and folding endurance than those of the soda paper, except of lower brightness .After 30 days of heat aging , these strength properties were still maintained . however, there was almost no difference in the infrared spectra and the crystallinities calculated by X-ray diffraction curves between the potassium carbonate paper and the soda a paper. The durability of the potassium carbonate paper was though to be due to decrease in the pulp damage caused by weak alkaline cooking condition. The results indicated that the paper prepared by the potassium carbonate cooling method could have better permanence than that prepared by the conventional soda cooking method.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.4
• /
• pp.24-33
• /
• 1991

The effects of thermomechanical treatments on microstructure and fatigue properties of 7050 Al alloy were investigated. The precipitation kinetics changed to a faster rate due to cold deformation employed in this special TAHA thermomechanical treatments including pre-aging, plastic deformation and two step final-aging. The G.P. zones in the under-aged condition were cut by dislocations and dissolved during the plastic deformation. During the low cycle fatigue, the T6' condition showed cyclic hardening behavior whereas the TMT5, TMT27 and T76 conditions showed cyclic softening at above 0.7% total strain amplitudes. The ${\Delta}K_{th}$ value of TMT27 was improved more than two times, compared with that of T76 condition. The T6' with small shearable precipitates resulted in the markedly high ${\Delta}K_{th}$ value. This is thought to be resulted from dislocation reversibility and roughness-induced crack closure due to planarity of slip.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.31-35
• /
• 2006

Degradation characteristics of filament-winded composites due to accelerated environmental aging have been evaluated under high temperature, water immersion and thermal impact conditions. Two kinds of laminated composites coated by an urethane resin have been used: carbon-fiber reinforced epoxy(T700/Epon-826, CFRP) and glass-fiber reinforced phenolic (E-glass/phenolic, GFRP). For tensile strength of $0^{\circ}$ composites, CFRP did high reduction by 25% under the influence of high temperature and water while CFRP showed little degradation. However for water-immersed $90^{\circ}$ composites both CFRP and GFRP showed high reduction in tensile strength. Bending strength and modulus of $90^{\circ}$ composites were largely reduced in water-immersion as well as high temperature environment. Urethane coating on the composite surface improved the bending properties by 20%, however hardly showed such improvement for water-immersed $90^{\circ}$ composites.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.47 no.2
• /
• pp.73-84
• /
• 2005

The main objective was to evaluate the tensile and bond properties of FRP rebar and durability performance after exposure of accelerated aging condition. Five types of FRP rebar include CFRP ISO, GFRP Asian, AFRP Technora, CFRP(D) and GFRP(D) rebars used in tensile and bond tests. Tensile test results of CFRP(D) and GFRP(D) were shown to possess acceptable tensile and durability performance compared with CFRP ISO, GFRP Asian, and AFRP Technora, Also, bond test results indicated that CFRP(D) and GFRP(D) rebars showed an ability to improve the bond strength.

• Journal of Korea Foundry Society
• /
• v.15 no.4
• /
• pp.351-359
• /
• 1995

The effects of In and Be additions on the aging behaviors and mechanical properties in the Al-Cu-Li alloy were investigated using the transmission electron microscope, the scanning electron microscope, hardness and tensile strength measurement. The aging is promoted and the double hardness peak is appeared by the addition of In and Be in the Al-Cu-Li alloy. The strength is increased, but the elongation and toughness are decreased by the addition of In in the Al-Cu-Li alloy. And the Al-Cu-Li-In-Be alloy has good combination with the strength, the elogation and toughness than Al-Cu-Li-In alloy.

• Journal of Environmental Science International
• /
• v.13 no.4
• /
• pp.421-427
• /
• 2004

With the help of mechanical mixing method such as Banbury mixer and open 2 roll mill, ethylene propylene diene terpolymer (EPDM) was blended with the chloroprene rubber (CR) then mechanical properties and ozone resistance test of blends were subsequently investigated. It was noted that the hardness increased with an increasing of CR contents. Generally the hardness was increased with heat aging time most likely due to the post cure. In ozone resistance test of blend, after 8 hours a portion of fine crack is obtained for pure CR. It is confirmed that ozone resistance is greatly improved by addition of 25wt% EPDM to CR.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.772-775
• /
• 2003

The development of new improved type of dielectric materials on the conception of multiphase structure has been carried out in this paper. Metal alkoxides solutions were used for application of thin film by electrophoretic deposition technique. We succeeded in preparation of amorphous and composite dielectric films from Al alkoxides. Specific features of the preparation technique were considered. Microstructure of the films was examined as well as their dielectric properties. TEM analyses reveals that films deposited from aging sols and heat-treated at temperatures as low as $400^{\circ}C$ contain small whiskers of ${\delta}-Al_2O_3$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.114-114
• /
• 2010

산불에 노출되는 경우 열충격으로 작용하는 패턴과 특성을 검토하여 가속열화시험에 반영하는 것이 필요하다. 본 연구에서는 산불환경을 모의하여 복합열화시험을 실시하기위해 복합가속열화 챔버를 구축하였다. 온도는 주로 $200^{\circ}C$에서 최대 $1000^{\circ}C$까지 변화를 주면서 예비시험과 본시험 실하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.2
• /
• pp.151-157
• /
• 2013

In this paper, properties of pattern using LBG (Linde-Buzo-Gray) Algorithm was explored including the exactness of K-means algorithm and process time of EM (Expectation Maximization) algorithm in order to develop analysis algorithm of partial discharge pattern in a cable using acoustic data analysis system. Partial discharge was measured by generating inner fault due to lamination of XLPE which is used for cable insulation material. Discharge pattern was analysed by changing the number of swarm article to 2, 4, and 6 in order to interpret swarm structure and properties.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.115-118
• /
• 2003

This research aims to measure mechanical tensile properties of CFRP composites for cryogenic tank material. Through the cryogenic chamber, tensile tests are peformed under cryogenic temperature for graphite/epoxy fabric specimen aged at $-150^{\circ}C$ for 30hrs with load and graphite/epoxy unidirectional specimen 3-cycled from RT to $-100^{\circ}C$ with load. For graphite/epoxy fabric specimen, tensile modulus showed to increase after aging at cryogenic temperature(CT) while to decrease after aging at room temperature(RT) and tensile strength is more decreased after CT-aged than at RT-aged. For graphite/epoxy unidirectional specimen, tensile modulus was almost not changed after 3-cycling but strength showed the trend of decrease as increase the number of cycling.