• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.89-95
• /
• 2000

The engine idle speed mode becomes worse as one drives a vehicle for several years. This is due to ageing of engine and power-train parts. In this case, unstable idle conditions such as engine stall and droop are frequently experienced when the engine gets heavy torque loads due to power steering pump and air conditioning compressor. The objective of this paper is to study on the idle speed control using PID controller under load disturbances. The input of the PID controller is an error of rpm. The output of the PID controller is an ISCV duty cycle. The dSPACE Controller Boards are used to interface with engine. The on-vehicle test is realized using by SIMULINK and BLOCKSETS tools. The real time interface control panel supplied by Control Desk S/W is designed to have good results in engine idle speed control.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.697-702
• /
• 1999

Among several non-destructive testing methods, ultrasonic pulse velocity method has been widely used for the evaluation of concrete strength. However, this method might not provide accurate estimated results since factors influencing the relationship between strength and wave velocity is not considered. In this study, the evaluation methods of concrete strength using compression wave velocities measured by either ultrasonic pulse velocity method or impact-resonance method are proposed. A basic equation is obtained by the linear regression with velocity vs. strength data at a specific age and then, ageing factor is employed in the equation to consider the difference of the increasing rate between wave velocity and strength. Strengths predicted by the proposed equation agree well with test results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.111-111
• /
• 2010

The mold transformers have been widely used in underground substations in large building and have some advantages in comparison to oil-transformer, that is low fire risk, excellent environmental compatibility, compact size and high reliability. In addition, the application of mold transformer for outdoor is possible due to development of epoxy resin. The mold transformer generally has cooling duct between low voltage coil and high voltage coil. A mold transformer made by one body molding method has been developed for small size and low loss, but it needs some cooling method because heat radiation between each winding is difficult. In this paper, the temperature distribution and thermal stress analysis of H class 100kVA pole cast resin transformer for power distribution are investigated by FEM program.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.309-314
• /
• 2000

Rubber is used as a primary suspension component in a vehicle or a mechanical structure. The aim of this study is to establish a procedure for measuring the material properties of rubber and to analyze the differences of material properties of virgin rubber and heat aged rubber. The effect of mechanical conditioning was shown and included in the procedures of tensile. compression. simple shear. and pure shear tests. In addition. using engine oil was recommended for compression test in order not to have barrelling. Moreover, based on the material properties of vil·gin rubber and heat aged rubber. equations of C10 and IRHD were proposed as a function of heat aging temperature and time.

• International Journal of Railway
• /
• v.6 no.1
• /
• pp.13-25
• /
• 2013

Railpad prevents damage of the tie and ballast by reducing the impact and high frequency vibration, which occurs when a vehicle load transfers to a tie. But elasticity of the railpad can decrease under vehicle load and over usable period. If that happens, railpad will become stiffer. Increase in stiffness of the railpad also translates into a rise in track maintenance cost because it accelerates the damage of the track. In this study, accelerated heat ageing test was performed to predict an expectable lifetime of the railpad. As a result, it was predicted to be about sixteen years at $25^{\circ}C$ that life time of railpad using NR rubber from Arrhenius relationship. Also, it was predicted to be about thirty-two days at $100^{\circ}C$. At this time, a standard rate of thickness change is approximately within 12%.

• Elastomers and Composites
• /
• v.13 no.2
• /
• pp.89-98
• /
• 1978

1. The effect of reactive type antioxidant, G-1 in comparism to ordinary antioxidant, SP, which are used for NR and SBR has teen studied, and its recipes are equal. The effects against ozone aye been shown that ill ordinary antioxidant, SBR, no an particular effect both for NR and SBR was found, where as in reactive type, considerable influence was recogniged particulary in dynamic ozone test. 2. The influence of reactive antioxidants on velcanization has been studied by means of Mooney viscometer and Rheometer. 3. The ageing properties of vulcanizates containing reactive antioxidant have been studied in terms of tensile strength.

• Journal of the Korean Society for Railway
• /
• v.7 no.4
• /
• pp.307-311
• /
• 2004

Arresters are the best protective device on electrical power systems against transient overvoltages generated by lightning and/or switching operation. Nonetheless, arresters are deteriorated by absorption of moisture in the environments of its use, repetition in the protective operation to overvoltages, and some defects at manufacturing. It is therefore important to estimate the electrical characteristic changes of ZnO blocks. In this paper, an accelerated ageing test by a standard lightning impulse current was carried out to extract parameters needed for arrester diagnosis, and leakage current components were measured. Total energy applied to the ZnO blocks at each time is about 1,050[J] in 8/20[${\mu}\textrm{s}$] impulse current. From the experimental results, we proposed electrical parameters and leakage current level to diagnose arrester soundness.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.1
• /
• pp.37-43
• /
• 2009

In this study, the physical properties of base paper for the manufacture of mulching mat for afforestation seedling were investigated. The base paper for mulching mat was prepared by stock conditions of PAE and AKD addition into the screened slurry of KOCC for the strengthening effects of wet tensile and burst strength. The optimum additions of PAE and AKD were considered at 2% and 0.5%, respectively. The accelerated aging by ISO 5630-1 and wet heat aging method under hot water for 2 kinds of commercial mulching and wet strength paper were compared with the base paper prepared for mulching mat manufacture. The accelerated aging test for the base paper prepared for mulching mat manufacture resulted in the same tendency of physical properties as two kinds of commercial products. However, the results of wet heat aging test under hot water indicated that the physical strength for base paper prepared was much higher than others. In addition, the opacity behavior for base paper prepared was enough effects to obstruct weeds growth by isolating transmission of sunlight.

• Journal of the Korean Society of Safety
• /
• v.27 no.3
• /
• pp.125-130
• /
• 2012

According to the Korea National Statistical Office data in 2010, the population over ages of 65 years would possess to 11.3% whole population of Korea in 2011 denoting Korea is already in the aging society. Old age is associated with inevitable time-dependent losses in physical capabilities. However the maintenance of physical capabilities is essential for continuing independence in old age. The work ability index(WAI) was constructed to reveal how well a worker is able to perform his work. This study focused on the discovery of an industrial and age-related influences on the work ability and job stress of workers in the shipbuilding, house managing, apartment construction industry. For this, the study conducted a job stress test using the Korean Occupational Stress Questionnaire Short Form, and employee performance evaluations using the Work Ability Index (WAI) of the Finnish Institute of Occupational Health (FIOH) on 3,228 workers in the shipbuilding, house managing and apartment construction industry. SPSS 12.0 K statistics program was used for statistics analysis and significance was verified with the Kruskal-Wallis test, a corporate body of nonparametric statistical analysis. As a result, employee performance had significant differences, depending on age, an industrial and years of service. The mean WAI score of the shipbuilding industry was lower than that of the other industry. Additionally, it was found that employee work ability decreased more as job stress increased.

• Journal of Fashion Business
• /
• v.19 no.5
• /
• pp.93-109
• /
• 2015

By the influence of ageing population, the well-being trend, and the increase of interest in health, people seems to be enjoying sports and outdoor life more. Followed by the change of consumers' life style, the interest in smart clothing grafting scientific technology has increased, and research on this subject is necessary. This study is to develop improved design of band type heating vests by grasping the weak point of currently sold heating vest designed by the manufacturer. Through this process, satisfaction of the consumer and the manufacturer can be increased. The results of this study are as follows: 1) Conducted a demand survey with the manufacturer and wearing evaluation test with the consumer on band type heating vests. 2) Suggested design drafts on band type heating vests for both genders reflecting demand survey results. 3) Conducted consumers' preference survey for design drafts. 4) Made the sample product, and then conducted an evaluation of wearing the actual product. Overall, the wearing test results showed high satisfaction for both genders.