• Journal of Radiation Protection and Research
• /
• 제43권3호
• /
• pp.114-119
• /
• 2018

Background: The retrospective dosimetry using RTL quartz can be improved by information for an optical sensitivity of sample connected with the equivalent dose determination. Materials and Methods: The quartz sample from a volcanic rock of Japan was used. After correcting the thermal quenching effect, RTL peaks of quartz were separated by the CGCD method cooperated with the general order kinetics. The number of overlapped glow peaks were ascertained by the $T_m-T_{stop}$ method. The optical sensitivity was examined by comparing the change of intensity on RTL glow peaks measured after exposure to light from a solar simulator with various illumination times. Results and Discussion: Seven glow peaks appeared to be overlapped on the RTL glow curve. The general order kinetics model was appropriate to separate glow peaks. After exposure to light from a solar simulator from a few minutes to 416 hr, the signals for peaks P4 and P5 decayed following the form of $f(t)=a_1e^{-{\lambda}1t}$, while the signals for peaks P6 and P7 decayed by the form of $f(t) = a_1e^{-{\lambda}1t}+a_2e^{-{\lambda}2t}+a_3e^{-{\lambda}3t}$. Conclusion: For dosimetric peaks, the times taken to reduce the RTL signal to half of its initial value were 70 sec for the peak P4, 54 s for the peak P5, 9,840 sec for the peak P6 and 26,580 sec for the peak P7, respectively. We conclude that the optical sensitivity of peaks P4, and P5 gives much higher than that of peaks P6 and P7.

• Preventive Nutrition and Food Science
• /
• 제10권1호
• /
• pp.17-21
• /
• 2005

This study was carried out to determine whether detection of minerals separated from irradiated mussel could be could be done by thermoluminescence (TL) method. After the minerals were separated by sodium polytungstate solution (2.0 g/mL) from irradiated mussel, organic compounds remaining in the minerals were removed by acid-base treatment and dried at 50℃ overnight, and then the minerals were measured through TL. The TL intensities of separated minerals at different irradiation doses during storage conditions of room and darkroom were obtained. TL intensity of first glow curves for minerals separated from irradiated mussel showed linear increase from the control to 5 kGy and slight increase from 5 kGy to 10 kGy. Since glow curve ratios of G2, G3 and G4, calculated from re-irradiated minerals measured immediately after irradiation and after storage of three months were over 0.5, detection of irradiation was possible. G1, which showed the glow curve ratios above 0.1, was classified as non-irradiated samples because the unique first glow curve was not found within the recommended temperature interval (150-230℃). Hence, on the basis of TL intensity, and glow curve ratio and shape, it is possible to correctly identify irradaited mussels after mineral separation during storage.

• Preventive Nutrition and Food Science
• /
• 제6권1호
• /
• pp.23-28
• /
• 2001

A study was carried out to establish a detection method of irradiated shellfish through thermoluminescence (TL). The TL intensity of first glow curves for irradiated bloody, freshwater, and short-neck shellfish increased from control until 5 kGy and increased slightly room 5 kGy until 10 kGy. Maximum TL temperatures of all irradiated samples tested were below 23$0^{\circ}C$, within temperature interval of 150~25$0^{\circ}C$ recommended for evaluation. Since just in control, glow curve ratios of G3 and G4 calculated from re-irradiated (1 kGy) bloody, freshwater and shortneck were over 0.5, detection in control was possible. However, as glow curve ratios after three months were below 0.5, detection by glow curve ratios after three months was impossible. Gl, which calculated from unirradiated samples, exhibited below 0.1, they were classified as unirradiated. In all samples, all the irradiated shellfish could be classified correctly as irradiated by hemaximum TL temperatures and shape of the second glow curve because those were shown in a lower temperature region than those of the first glow curve.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.489-489
• /
• 2012

The vibrational distribution of $N_2$ (B, v') in after-glows in $N_2$ RF flowing plasma was investigated. The optical emission of the after-glow was studied as function of distance from plasma. In a tube 2.1 cm, the gas pressure varied 8 Torr with 1000sccm nitrogen gas flowing late.. The discharges were excited by two ring-electrode powered by RF 13.56 MHz 100 Watt. $N_2$ (B, v') vibrational distribution was analyzed to see depends of position in after-glow. Dissociation rate of $N_2$ varied showing maximum in the late after-glow region. We studied $N_2$ RF capacitive flowing plasmas and afterglows by emission spectroscopy and by NO titration to determine the density of N-atoms.

• 한국응용과학기술학회지
• /
• 제19권3호
• /
• pp.174-180
• /
• 2002

In recent days, the study of a new phosphorescent phosphor has been performed in order to overcome the defect of sulfide phosphor and increase the brightness and long after-glow characteristic of phosphorescent phosphor. Particularly, sulfide phosphor usually used is so chemically unstable that the study of oxide phosphors are processing. $Eu^{2+}$, $Nd^{3+}$ doped Ba-Al-O phosphors sintered at $600{\sim}1500^{\circ}C$ for 2hours had the PL emission spectrum and after-glow over $1200^{\circ}C$. In this system, as the mole concentration of alumina increases, emission bands of phosphors moved from 500nm to 380nm. The optimum concentration of flux was 5wt% and after-glow characteristics of phosphors were found at the host material molar ratio ($BaCO_{3}:Al_{2}O_{3}$), 1:1 and 1:3.

• 한국식품과학회지
• /
• 제32권3호
• /
• pp.525-530
• /
• 2000

국내에서 생산된 농산물의 방사선 조사유무를 확인하기 위하여 TL을 측정하였다. 모든 시료의 first glow curve는 조사선량이 증가할수록 TL intensity도 증가하는 경향을 보여 주었다. 당근, 생강, 감자, 고구마의 상관계수는 0.8522, 0.9968, 0.9612, 0.9071의 높은 값을 나타내었으며, first glow curve의 최대발광온도점은 $176.16{\sim}190.08^{\circ}C$사이에 있었고, second glow curve는 $143.84{\sim}146.56^{\circ}C$ 사이에서 나타났다. Glow curve ratio 1은 감자와 고구마를 제외하고 모두 0.1보다 작은 수치를 보여 비조사시료로 확인되었으며, 감자(0.1840)와 고구마(0.1655)는 0.1보다 큰 수치를 보였으나 독특한 first glow curve가 나타나지 않은 점으로 보아 비조사시료로 확인되었다. 그리고 모든 시료의 glow curve ratio 2는 0.7159보다 높은 수치를 나타내어 조사시료로 확인되었다. Glow curve의 모양을 분석한 결과 second glow curve의 모양이 first glow curve의 유사하였고, 더 낮은 온도에서 나타났다. 따라서 glow curve ratio와 glow curve의 모양에 의해 정확하게 조사유무를 확인할 수 있었고 TL을 이용하여 방사선 조사된 농산물의 검지가 가능함을 확인할 수 있었다.

• Preventive Nutrition and Food Science
• /
• 제7권2호
• /
• pp.188-194
• /
• 2002

This study was carried out to observe changes in several detection factors derived from thermoluminescence (TL) of minerals separated from irradiated Korean perilla and sesame seeds during storage under normal room and darkroom conditions. The TL intensities of the first glow curves increased from 0 to 5 kGy but only slightly increase from 5 to 10 kGy. Maximum TL temperatures of the first glow curves in all irradiated samples were around 20$0^{\circ}C$, ranging from 150 to 25$0^{\circ}C$. Since the control (0 day of storage) glow curve ratios of G3 and G4, calculated from re-irradiated (1 kGy) sample were over 0.5, detection of irradiation was possible. However, because Gl ratios were below 0.1, they were classified as non-irradiated. There was n unique first glow curve shape that could be clearly seen in all irradiated samples, regardless of storage conditions, that was never seen in non-irradiated samples. In all samples, the maximum TL temperatures and shape of the second glow curve was in a lower temperature range than that of the first glow curve. Therefore, detection of irradiated Korean perilla and sesame seeds was possible fur up to 3 months after irradiation, regardless of storage conditions, by examining several TL detection factors; including TL intensity, glow curve ratios maximum TL temperatures, and the shapes of glow curves.

• 대한안전경영과학회지
• /
• 제25권1호
• /
• pp.61-66
• /
• 2023

The purpose of this study is to compare and analyze the flame retardant performance of Japanese cypress(Chamaecyparis obtusa) plywood, commonly used in indoor decoration, furniture, and tableware, by treating it with three different fire retardants with different primary ingredients. The experiment was conducted in compliance with Article 31, Paragraph 2 of the Enforcement Decree of the Fire Facilities Installation and Management Act and Articles 4 and 7-2 of the Flame Retardant Performance Standards. After flame time, after glow time, char length, and char area were measured. As a result, first, after flame time was measured at 0 seconds regardless of whether the flame retardant treatment was applied. Second, after glow time was relatively long, measuring 22.7 seconds without treatment, which is likely due to the weak fire resistance and high concentration of carbon monoxide generated by the chemical characteristics of the Japanese cypress itself. Third, it was confirmed that the effects of the primary ingredient, phosphorus, in the flame retardant treatment varied depending on the technological development of the manufacturers of the same species of Japanese cypress plywood. In the future, it is expected that the results of this study will provide fundamental data to select flame retardant treatments that show high flame retardant performance according to the botanical characteristics of the wood.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.911-914
• /
• 1992

We have investigated the micro-discharge in plasma display panel using 2 dimensional 2 fluid MHD equations. Plasma display utilizes the physical phenomena of the normal glow or abnormal glow and is considered to be able to provide the largest display area among various flat panel. 2 fluid, 2 dimensional Magneto-Hydro-Dynamic equations are applied to Computational field of 100${\times}$800${\mu}m^2$. Time varing glows and after-glows were investigated for 11 $\mu$sec. We obtained the distribution of the microscopic variables such as the density, temperature, velocity of Ne+Ar0.1% gas plasma. During the first 6$\mu$ sec, glow discharge dued to DC pulse was investigated. Time varing phenomena of after-glow was also investigated during the last 5 $\mu$set. From results, it was found that the driving efficiency of a DC Plasma Display Panel could be improved when the diffusion of ions and electrons are controlled by the pulses applied to the auxiliary anode.

• 한국방사선학회논문지
• /
• 제8권4호
• /
• pp.181-187
• /
• 2014

본 연구는 방사선 치료 영역의 선량 측정을 위하여 상용화된 열형광선량계의 가열 온도에 따른 형광 곡선의 특성을 분석하였다. 본 연구에 사용된 열형광선량계는 LiF:Mg${\cdot}$Ti, LiF:Mg${\cdot}$Cu${\cdot}$P, $CaF_2$:Dy, $CaF_2$:Mn(Thermo Fisher Scientific Inc., USA)이었다. 선원과 고체 팬텀 표면(RW3 slab, IBA Dosimetry, Germany)간 거리를 100cm로 하여 기준점 깊이에서 6MV, 15MV X선과 6MeV, 12MeV 전자선을 각각 100MU 조사하였다. 방사선 조사 후 열형광 판독기(Hashaw 3500, Thermo Fisher Scientific Inc., USA)를 사용하여 $50^{\circ}C$에서 $260^{\circ}C$까지 $15^{\circ}C/sec$의 가온율로 가열하여 형광 곡선을 분석하였다. 트랩 준위에 포획된 전자가 정공과 결합하면서 빛을 방출하는 형광 피크(glow peak)는 2개 또는 3개의 피크가 나타났으며 방사선 조사 후 TLD의 온도를 일정하게 증가시켰을 때 최대 형광 피크를 나타내는 형광 온도의 경우 각각의 에너지에 따라 $LiF:Mg{\cdot}Ti$ 선량계는 $185.5{\pm}1.3^{\circ}C$, $LiF:Mg{\cdot}Ti$ 선량계는 $135.0{\pm}5.1^{\circ}C$, $CaF_2$:Dy 선량계는 $144.0{\pm}1.6^{\circ}C$, $CaF_2$:Mn 선량계는 $294.3{\pm}3.8^{\circ}C$ 근처에서 최대 형광 피크를 각각 나타났다. 방사선 조사 후 포획 전자의 형광 방출 확률은 가열 온도에 의존하게 되므로 방사선 치료 영역의 선량 측정에서 방사선 조사 후 열형광선량계에 일정한 가온율을 적용함으로써 고유한 물리적 특성에 따른 측정 정확도를 향상시킬 수 있을 것으로 판단되었다.