The two dimensional size effect of specimen gauge section ($length{\;}{\times}{\;}width$) was investigated on the compressive behavior of a T300/924 $\textrm{[}45/-45/0/90\textrm{]}_{3s}$, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a $30mm{\;}{\times}{\;}30mm,{\;}50mm{\;}{\times}{\;}50mm,{\;}70mm{\;}{\times}{\;}70mm{\;}and{\;}90mm{\;}{\times}{\;}90mm$ gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.
Journal of the Korean Society for Aviation and Aeronautics
/
v.15
no.1
/
pp.38-53
/
2007
In a seminal judgment of November 2002 (Case C-476/98) relating to the compatibility with Community laws of the 'nationality clause' in the 1996 amending protocol to the 1955 U.S.-German Air Services Agreement, the European Court of Justice(ECJ) decided that the provision constituted a measure of an intrinsically discriminatory nature and was thus contrary to the principle of national treatment established under Art. 52 of the EC Treaty. The Court, rejecting bluntly the German government' submissions relying on public policy grounds(Art. 56, EC Treaty), seemed content to declare and rule that the protocol provision requiring a contracting state party to ensure substantial ownership and effective control by its nationals of its designated airlines had violated the requirement of national treatment reserved for other Community Members under the salient Treaty provision. The German counterclaims against the Commission, although tantalizing not only from the perusal of the judgment but from the perspective of international air law, were nonetheless invariably correct and to the point. For such a clause has been justified to defend the 'fundamental interests of society from a serious threat' that may result from granting operating licenses or necessary technical authorizations to an airline company of a third country. Indeed, the nationality clause has been inserted in most of the liberal bilaterals to allow the parties to enforce their own national laws and regulations governing aviation safety and security. Such a clause is not targeted as a device for discriminating against the nationals of any third State. It simply acts as the minimum legal safeguards against aviation risk empowering a party to take legal control of the designated airlines. Unfortunately, the German call for the review of such a foremost objective and rationale underlying the nationality clause landed on the deaf ears of the Court which appeared quite happy not to take stock of the potential implications and consequences in its absence and of the legality under international law of the 'national treatment' requirement of Community laws. Again, while US law limits foreign shareholders to 24.9% of its airlines, the European Community limits non-EC ownership to 49%, precluding any ownership and effective control by foreign nationals of EC airlines, let alone any foreign takeover and merger. Given this, it appears inconsistent and unreasonable for the EC to demand, $vis-{\grave{a}}-vis$ a non-EC third State, national treatment for all of its Member States. The ECJ's decision was also wrongly premised on the precedence of Community laws over international law, and in particular, international air law. It simply is another form of asserting and enforcing de facto extraterritorial application of Community laws to a non-EC third country. Again, the ruling runs counter to an established rule of international law that a treaty does not, as a matter of principle, create either obligations or rights for a third State. Aside from the legal problems, the 'national treatment' may not be economically justified either, in light of the free-rider problem and resulting externalities or inefficiency. On the strength of international law and economics, therefore, airlines of Community Members other than the designated German and U.S. air carriers are neither eligible for traffic rights, nor entitled to operate between or 'free-ride' on the U.S. and German points. All in all and in all fairness, the European Court's ruling was nothing short of an outright condemnation of established rules and principles of international law and international air law. Nor is the national treatment requirement justified by the economic logic of deregulation or liberalization of aviation markets. Nor has the requirement much to do with fair competition and increased efficiency.
Under the Aviation Safety Act of Korea, any person who intends to operate a drone is required to follow the operational conditions listed below, unless approved by the Minister of Land, Infrastructure, Transport and Tourism; (i) Operation of drones in the daytime, (ii) Operation of drones within Visual Line of Sight, (iii) Maintenance of a certain operating distance between drones and persons or properties on the ground/ water surface, (iv) Do not operate drones over event sites where many people gather, (v) Do not transport hazardous materials such as explosives by drone, (vi) Do not drop any objects from drones. Requirements stated in "Airspace in which Flights are Prohibited" and "Operational Limitations" are not applied to flights for search and rescue operations by public organizations in case of accidents and disasters. This paper analyzes legal issues as to definition and regulations of drones in Korean Aviation Safety Act. This paper, also, offers some implications and suggestions for regulations of drones under Korean Aviation Safety Act by comparing the regulations of drones in Japanese Civil Aeronautics Act.
In order to satisfy the intellectual curiosity of mankind to explore the unknown, National Aeronautics and Space Administration (NASA) in the United States and European Space Agency (ESA) in Europe are embarking on various R&D under the motto of the grand dream of pioneering space into a safe and sustainable environment. In the 2020s and 30s, it is expected that advanced giant observation equipment will be in operation, such as the development of a 10-meter-class telescope in space. In Korea, following the development of the 0.15 m Near-Infrared Imaging Spectrometer (NISS), Korea Astronomy and Space Science Institute (KASI) is also participating a 0.2 m Spectro-Photometer for the History of the Universe, Epoch of Reionization, and Ices Explorer (SPHEREx) as an international cooperation partner in small exploration telescope. However, domestic experience in the development and operation of the space telescopes is still insufficient, and there is no plan with long-term prospects for constructing telescopes. In order to answer questions about the unknown world that mankind has not experienced using our own equipment, planning and preparation for the construction of a space telescope through close cooperation among industry-university-institute-government is urgently needed. In this paper, the necessity, background, development goals, and expected effects of the development of the Korean Space Telescope are summarized conceptually, and a working group (WG) is also proposed. In the WG activities, Korea shall take the lead in establishing the Korean-style space telescope development plan, and will start a valuable step to establish the national direction in the field of space astronomy and related technologies. We hope that the WG will be another milestone in Korea's space development.
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.48
no.6
/
pp.443-453
/
2020
This study using the active vibration control technique attempts to alleviate numerically the airframe vibration of a UH-60A helicopter. The AVCS(Active Vibration Control System) is applied to reduce the 4/rev vibration responses at the specified locations of the UH-60A airframe. The 4/rev hub vibratory loads of the UH-60A rotor is predicted using the nonlinear flexible dynamics analysis code, DYMORE II. Various tools such as NDARC, MSC.NASTRAN, and MATLAB Simulink are used for the AVCS simulation with five CRFGs and seven accelerometers. At a flight speed of 158knots, the predicted 4/rev hub vibratory loads of UH-60A rotor excite the airframe, and then the 4/rev vibration responses at the specified airframe positions such as the pilot seat, rotor-fuselage joint, mid-cabin, and aft-cabin are calculated without and with AVCS. The 4/rev vibration responses at all the locations and directions are reduced by from 25.14 to 96.05% when AVCS is used, as compared to the baseline results without AVCS.
Through the use of finite element analysis and acoustic emission techniques we have evaluated the interfacial failure of a carbon fiber reinforced polymer (CFRP) repair patch on a notched aluminum substrate. The repair of cracks is a very common and widely used practice in the aeronautics field to extend the life of cracked sheet metal panels. The process consists of adhesively bonding a patch that encompasses the notched site to provide additional strength, thereby increasing life and avoiding costly replacements. The mechanical strength of the bonded joint relies mainly on the bonding of the adhesive to the plate and patch stiffness. Stress concentrations at crack tips promote disbonding of the composite patch from the substrate, consequently reducing the bonded area, which makes this a critical aspect of repair effectiveness. In this paper we examine patch disbonding by calculating the influence of notch tip stress on disbond area and verify computational results with acoustic emission (AE) measurements obtained from specimens subjected to uniaxial tension. The FE results showed that disbonding first occurs between the patch and the substrate close to free edge of the patch followed by failure around the tip of the notch, both highest stress regions. Experimental results revealed that cement adhesion at the aluminum interface was the limiting factor in patch performance. The patch did not appear to strengthen the aluminum substrate when measured by stress-strain due to early stage disbonding. Analysis of the AE signals provided insight to the disbond locations and progression at the metal-adhesive interface. Crack growth from the notch in the aluminum was not observed until the stress reached a critical level, an instant before final fracture, which was unaffected by the patch due to early stage disbonding. The FE model was further utilized to study the effects of patch fiber orientation and increased adhesive strength. The model revealed that the effectiveness of patch repairs is strongly dependent upon the combined interactions of adhesive bond strength and fiber orientation.
Park, Ill-Kyung;Kim, Seung-Jun;Choe, Ik-Hyun;An, Seok-Min;Yeo, Chan-Hong
Transactions of the Korean Society of Mechanical Engineers A
/
v.34
no.1
/
pp.117-124
/
2010
The bird strike to small aircraft has not been an issue because of its low speed and usage as a private aircraft. So, the compliance of the bird strike regulation is limited to large fixed-wing aircraft such as the commuter category in FAR Part 23 and the civil aircraft in FAR Part 25, generally. However, the forecast of dramatic increasing of VLJ(Very Light Jet), the usage of a composite material for an aircraft structure and flight time of general aviation due to Air-taxi for the point to point transportation, would rise up the need of bird strike regulations and a safety enhancement in normal and utility categorized aircraft. In this study, the safety of bird strike to small aircraft wing leading edge made of a metal and a composite material were compared using the explicit finite element analysis.
Rejected Takeoff Accidents are not common. but if occurred, it leads to big disaster From the year of 1959, when Jet Transport service opened, to the year of 2000, Rejected Takeoff accidents/incidents occurred total of 94 cases. All cases led to overrun, and major cause is to initiate stopping maneuvers over $V_1$, takeoff decision speed, according to National Transport Safety Board of America. Similar results are represented in Aviation Safety Reporting System of National Aeronautics and Space Administration. So I believe that it is worth studying if Airplane Flight Manual, which is the reference Performance criteria, is appropriate to operations of line pilots. The definition of $V_1$ has been revised a couple of times and Rejected Takeoff Certification Standards for Transport Airplanes was changed in 1998. It shows that up to now there are some portions unreasonable. This study focused on gathering the pilot's tendency for current Rejected Takeoff Procedures of K airlines and analyze the factors they concern. I chose B777 airplane and actually measured the recognition and reaction time of the rejected takeoff transitions through Simulators. And compared the results with the data of flight test and Airplane Flight Manual.
Korean Journal of Agricultural and Forest Meteorology
/
v.17
no.2
/
pp.102-107
/
2015
This study was conducted to classify agro-climatic zones in Northeast district of China. For agro-climatic zoning, monthly mean temperature and precipitation data from Global Modeling and Assimilation Office (GMAO) of National Aeronautics and Space Administration (NASA, USA) between 1979 and 2010 (http://disc.sci.gsfc.nasa.gov/) were collected. Altitude and vegetation fraction of East Asia from Weather Research and Forecasting (WRF) were also used to classify them. The criteria of agro-climatic classification were altitude (200 m, between 200-800 m, 800 m), vegetation fraction (60%), annual mean temperature ($0^{\circ}C$), temperature in the hottest month ($22^{\circ}C$), and annual precipitation (700 mm). In Northeast district of China, mean annual temperature, annual precipitation, and solar radiation were $3.4^{\circ}C$, 613.2 mm, and $4,414.2MJ/m^2$ between 2009 and 2013, respectively. Twenty-two agro-climatic zones identified in Northeast district of China by metrics classification method, from which the map of agro-climatic zones for Northeast district of China was derived. The results could be useful as information for estimating agro-meteorological characteristics and predicting crop development and crop yield of Northeast district of China as well as those of North Korea.
Base researches in geoscience and mineral resources, such as geological and geo-thematic mapping, geological survey and observation, have long-term, continuity and time-leasing characteristics and they are difficult to present the particular research stages or progressions in the research span. The Technology Readiness Levels (TRLs), developed by the U.S. National Aeronautics and Space Administration (NASA), is effective for presenting research maturity levels and progression in the development of new technologies. This study suggests adjusted definitions for the Technology Readiness Levels to fit Geo-technology (Technology in Geoscience and Mineral Resources). Base geological researches, including mapping, surveys and observation, can be also presented in research levels from TRL 1 (R&D planning, literature survey) to TRL 9 (geological information construction and service in all target areas) in terms of the final product's coverage. Moreover, not only development and construction of commercial products, geological disasters and environmental researches can also be presented in field demonstrations through public pilot applications. The modified commercialization or cemonstration TRLs in Geo-technology are TRL 5 (starting pilot field application), TRL 6 (pilot field operation) and TRL 7 (pilot field operation for a larger scale, greater than ten percent of the actual environment).
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.